Ankbit RT8003 Wireless Audio Adapter User Manual
Instruction
In the box
- x1
- x1
- x1
- x1
- x1
- x1
Product Description
- 3.5mm male plug
- Volume up/Next track
- Multi-function button
- Volume down/previous track
- Pair / Reset
- TX=Transmitter Mode
OFF=Power OFF
RX=Receiver Mode - Microphone
- DC 5V charging port
Charging the adapter
The LED light remains red when charging and turns off when fully charged.
TX mode
- Enter transmitter mode
- Pair with your headphone
- Plug into audio output port
Switch to TX mode, the TX LED will quickly flash red-blue, then set your Bluetooth headset to pairing mode, keep it close to the adapter, and wait for pairing to succeed
RX mode
- Enter receiver mode
- Pair with your phone
- Plug into audio input port
Switch to RX mode, the RX LED will quickly flash red-blue, then activate the Bluetooth on your phone, click “SafeFly Dot” to connect, keep it close to the adapter, and wait for pairing to succeed
Dual connection
When connected to device A, press and hold the P/R button for 25 to enter pairing mode, and repeat the step2 of TX/RX to pair with device B
Button Controls
x1: Press once
1s: Press and hold for 1 second
Battery level
Power on: Battery level
 |
 |
 |
|
 |
|
 |
|
 |
Triple-click the “M” button to check remaining power.
Reset
Press and hold the P/R button for 8 seconds to reset
FCC
Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
eVatmaster Consulting GmbH
Bettinastr. 30
60325 Frankfurt am Main, Germany
contact@evatmaster.com
OST_EU_20210429000166
We simply act as EU representative for cross-border sellers, and are not manufacturers/importers/distributors for the product, nor involved in the manufacture/import/sale of the product. Therefore, we are not responsible for any after-sales services related to the product. In case of any product quality or infringement issues, the manufacturer/importer/seller shall be solely held responsible
Operator: Ankbit International Limited
Address: 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong
Manufacturer: ShenZhen Ankbit Electronics Limited
Address: Runfeng Industrial Park, No. 4197 Baoan Blvd., Xixiang St., Baoan Dist., Shenzhen, China
FCC ID: 2A6ET-RT8003
IC: 29252-B03
HVIN: B06
MADE IN CHINA
Documents / Resources
 |
Ankbit RT8003 Wireless Audio Adapter [pdf] User Manual 2A6ET-RT8003, 2A6ETRT8003, RT8003 Wireless Audio Adapter, RT8003, Wireless Audio Adapter, Audio Adapter, Adapter |