ANENG VD808 Socket Circuit Analyzer Instruction Manual

ANENG VD808 Socket Circuit Analyzer

ANENG VD808 Socket Circuit Analyze

Overview

The socket circuit analyzer is a 2-in-1 pocket pen-type intelligent multi-purpose meter and power polarity detector. The machine has stable performance, high reliability, clear reading, and overload protection functions. Driven by 2 AAA 1.5V batteries, the meter adopts a large-screen LCD display, and whether the home electricity protection system is normal, it can remind users to make adjustments to the socket with faults and potential safety hazards in time, and overhaul your protection system to ensure the safety of home electricity. It is an extremely ideal instrument for the majority of users. This series of meters can be used to test 1.5V/30V batteries and AC voltage, on-off, non-contact voltage measurement, and socket detection. It is a tool with superior performance. It is an ideal tool for laboratories, factories, radio enthusiasts, and households.

Read the instruction manual carefully before use

Character

  1. General characteristics:
    1. Display mode: liquid crystal display;
    2. Low voltage display: ” Display Symbol ” symbol appears;
    3. Working environment: (0~ 40) °C, relative humidity < 80%;
    4. Power supply: AAA 2×1.5V battery;

Operation panel instructions

  1. Test nib: voltage, positive end test point;
  2. Flashlight
  3. VA color reverse display screen;
  4. AC voltage, 1.5V~ 30V battery, on-off, electric field-sensitive finger contact points.
  5. Long press ” Wifi Icon ” to enter the on-off detection;
  6. Short press the ” Icon ” button to turn it on and long press to turn it off. Short press the switching function in the power-on state (it will automatically shut down after 5 minutes without induction);
  7. Leakage trip detection button;
  8. Long press: turn on/off flashlight; single press: data hold
  9. Socket protective cover
    Operation panel instructions

Operating instructions

  1. AC voltage measurement: short boot, click ” Icon ” AC voltage measurement, the probe tip 1 of the test pen contacts the AC voltage conductor, and the finger is in reliable contact with the contact point 4. The corresponding AC voltage is displayed on the display screen, and the neutral line or live line can also be judged according to the size of the AC voltage;
  2. Induction mode measurement: trigger the ” Icon” button after booting, the screen has an “EF” display, enter the induction measurement, and place the probe tip of the test pen close to the AC voltage source. At the same time, the buzzer will emit an enhanced or decreased sound according to the strength of the signal; it can distinguish between zero live wires and find the breakpoint of live wires;
  3. Wire conduction: After turning it on, pinch one end of the uncharged wire with your left hand, and the probe tip 1 of the test pen is in reliable contact with the other end of the wire. At the same time, press the button “Buzzer” to make contact. If the wire is conducting, it will display ” Icon  “. If the wire is open, it will show that the ” Icon  ” buzzer is not ringing. Attention: Do not touch the 4 contact points during the measurement on-off process.
  4. Battery test: After booting, press and hold the negative electrode of the 1.5V or 30V battery with your left hand, the probe tip 1 of the test pen is in reliable contact with the positive electrode of the battery, and the finger is in reliable contact with the contact point 4. The corresponding battery voltage is displayed on the display screen. If the polarity is measured in reverse, the display will display a ” Icon ” error and alarm.
  5. Socket test: Check whether all levels of the power socket are correct, insert the plug into the socket under test after confirming that it is correct, observe the display status of the socket test instrument, and compare the parameter table according to the display situation to know the connection of each board of the socket under test
  6. Technical parameters:
  7. Working voltage: AC voltage: 2-440V, 50Hz-60Hz; measurement error: ± (6% + 10)
  8. Use environment: working temperature 0-40 degrees: storage temperature; -10-50 degrees: humidity 75%: altitude ≤2000 meters;
  9. Socket rated voltage; Un-220V-250AC; Rated residual operating current I Delta n-30mA (European Union standard); Grounding resistance meets the specification design requirements;

Socket Wiring

Socket Wiring Correct (display normal) Socket Wiring The phase line and the zero line are reversed (the phase line and the zero line flash at the same time)
Socket Wiring Missing ground wire (ground wire flashing) Socket Wiring The phase line and the ground line are reversed (the phase line and the ground line flash at the same time)
Socket Wiring Missing zero line (zero line flashing) Socket Wiring Missing phase line (all blinking)
Socket Wiring The phase is wrong and the ground is missing (the phase line and the ground line flash alternately)

Operational approach

When measuring AC voltage, the fingers must contact the touchpoints on both sides
Operational Approach

Measure the DC voltage by touching two touchpoints with one hand and contacting the negative electrode of the battery
Operational Approach

Symbol Make sure your fingers are in contact with the A touch points on both sides before measuring
Operational Approach

Logo

Documents / Resources

PDF thumbnailVD808 Socket Circuit Analyzer
Instruction Manual · ANENG, VD808, Tester, Socket

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.