ANCEL AS100 OBDII EOBD Code Reader User Guide User Guide

ANCEL AS100
OBDII/EOBD Code Reader — User Guide

Product Information

The AS100 checks the engine of all vehicles that comply with OBDII, run on 12 V and have the standardized 16-pin connector.

1.1. Location of the Data Link Connector (DLC)
On most vehicles the DLC is located about 30 cm (12 inches) from the center of the instrument panel (dash), under or around the driver’s side.

1.2. Tool Description

1. LCD display– shows the menus and the test results.
2. Green LED– indicates that the engine is working correctly and no DTC is stored.
3. Yellow LED– indicates a possible problem: some diagnostics could not be performed and/or a DTC is pending.
4. Red LED– indicates a problem in the engine. The MIL (malfunction indicator light) on the dashboard may be on.
5. BACK button– exits and returns to the previous menu.
6. OBDII connector– plug it into the vehicle’s OBD socket so that the tool can communicate with the vehicle’s data link connector (DLC).
7. UP button– on the main screen, opens the setup menu. Once the vehicle has been scanned, moves up through the menu.
8. OK button– opens the next menu or accepts the current option.
9. DOWN button– moves down through the menu.

1.3. Specifications

1.4. Functions

1. Dual-system diagnostics: engine or transmission.
2. Quick indication of engine faults by the green, yellow and red LEDs.
3. Reads or clears engine fault codes and shows the DTC definition.
4. Shows sensor data streams, up to 249 parameters.
5. Shows freeze frame data and I/M readiness status.
6. Reads vehicle information: vehicle identification number (VIN), calibration IDs and calibration verification numbers (CVNs).
7. Nine menu languages: German, English, Spanish, French, Italian, Dutch, Polish, Finnish and Russian.

Instructions

2.1. Dual-System Selection
Start the engine and plug the OBDII connector into the vehicle’s OBDII socket.
The tool powers on and shows its main screen.
Press OK to start scanning the vehicle’s systems through the DLC. If only one system is found, the tool opens the engine system directly. If both systems are found, it opens the system selection menu: select the system to be tested.

1. $ 7E8: Engine– engine system.
2. $ 7E9: A/T– transmission system.

2.2.Diagnostic Menu

1. Read Codes: reads the diagnostic trouble codes (DTCs) stored in the engine or transmission and displays their standard definitions.
2. Erase Codes: clears all DTCs in the system.
3. Data Stream: reads and displays all supported live sensor data, up to 249 parameters.
4. Freeze Frame: the freeze frame data record the operating state of the vehicle (fault code, vehicle speed, engine speed, coolant temperature, etc.) at the moment an emission-related fault occurred.
5. I/M Readiness: checks the operation of the emission control systems on OBD2-compliant vehicles. Some recent vehicles support two types of I/M readiness test:
   •Since DTCs Cleared– the status of the monitors since the DTCs were erased;
   •This Drive Cycle– the status of the monitors since the start of the current drive cycle.
   OK: diagnostic test completed; INC: diagnostic test not completed; N/A: not supported.
6. Vehicle Information: shows the vehicle identification number (VIN), the calibration IDs (CALID) and the calibration verification numbers (CVN).

2.3. Setup
On the main screen, press the UP button to open the setup menu.

1. Language: English by default; other languages can be selected.
2. Unit of measure: metric or imperial units; metric by default.
3. Contrast: the display contrast is adjustable; 25% by default.

Service and Support

If you have any questions, please contact your local store or distributor, or visit https://www.anceltech.com.
If the scan tool needs to be repaired, contact your local distributor for more information.

3.1. Disposal
Do not dispose of this product with household waste. At the end of its life, take it to a collection point for the recycling of electrical and electronic equipment (Directive 2012/19/EU).

3.2.Manufacturer
OBDSPACE TECHNOLOGY CO., LTD
D03, Block A, No. 973 Minzhi Ave., Longhua District, Shenzhen, Guangdong, China
support@anceltech.com
https://www.anceltech.com

Distributor
Sunnysoft s.r.o.
Kovanecka 2390/1a
190 00, Praha 9 – Liben
www.sunnysoft.cz