General Description
The EVAL-LTM4682-A1Z evaluation board features the LTM®4682: the wide input and output voltage range, high efficiency and power density, quad output PolyPhase® DC-to-DC step-down µModule® (micromodule) power regulator with digital power system management (PSM). The EVAL-LTM4682-A1Z evaluation board is configured as a 4-phase four output. A similar evaluation board with a 4-phase single output is also available (EVAL-LTM4682-A2Z).
The EVAL-LTM4682-A1Z evaluation board’s default input voltage range is 4.5V to 16V. However, if VIN is lower than 6V and within 4.5V VIN 5.75V, a minor modification to certain existing on-board components is required. See step 8 (Operation at Low VIN: 4.5V VIN 5.75V) in the Procedure section.
The factory default output voltage VOUT [0:3] is 0.7V at 31.25A maximum load current per channel. Each channel can deliver up to 31.25A maximum load current, but forced airflow and heatsink might also be used to further optimize the output power when all output rails are on and fully loaded. The evaluation board output voltages can be adjusted from 0.7V up to 1.35V. Refer to the LTM4682 data sheet for thermal derating curves and recommended switching frequency when adjusting the output voltage.
Evaluation Board Photo

The factory default switching frequency is preset at 575kHz (typical). The EVAL-LTM4682-A1Z evaluation board comes with a PMBus interface and digital PSM functions. An on-board 12-pin connector is available for the users to connect the dongle DC1613A to the evaluation board, which provides an easy way to communicate and program the part using the LTpowerPlay® software development tool.
The LTpowerPlay software and the I2C/PMBus/SMBus dongle DC1613A allow the users to monitor real-time telemetry of input and output voltages, input, and output current, switching frequency, internal IC die temperatures, external power component temperatures, and fault logs. Programmable parameters include device address, output voltages, control loop compensation, switching frequency, phase interleaving, discontinuous-conduction mode (DCM) or continuous-conduction mode (CCM) of operation, digital soft start, sequencing, and time-based shutdown, fault responses to input and output overvoltage, output overcurrent, IC die and power component over temperatures.
The LTM4682 is available in a thermally enhanced, lowprofile 330-pin (15mm × 22mm × 5.71mm) BGA package. It is recommended to read the LTM4682 data sheet and this user guide prior to using or making any hardware changes to the EVAL-LTM4682-A1Z evaluation board.
Ordering Information appears at end of data sheet.

Figure 1. EVAL-LTM4682-A1Z Evaluation Board (Part Marking is either ink Mark or Laser Mark)

Rev. 0 One Analog Way, Wilmington, MA 01887-2356, U.S.A.

DOCUMENT FEEDBACK Tel: 781.329.4700

Evaluation Board User Guide

EVAL-LTM4682-A1Z

Performance Summary
Specifications are at TA = 25°C

PARAMETER Input voltage VIN range
Evaluation board default output voltage, VOUT0OUT3 Switching frequency, fSW

CONDITIONS
fSW = 575kHz, VIN = 4.5V to 14V, IOUT = 0A to 31.25A per channel. Factory default switching frequency.

Maximum continuous output current per channel, IOUT0OUT3

MIN TYP MAX UNIT

4.5

0.697 0.7 0.704 V

575

kHz

30 31.25 A

Efficiency

fSW = 575kHz, VIN =12V, VOUT0 = 0.7V,

IOUT0 = 20A

86.7

IOUT0 = 0A to 31.25A, VBIAS = 5.5V

(RUNP: ON), only one channel is on at a

time, no forced airflow, no heatsink

IOUT0 = 31.25A

Thermal performance

fSW = 575kHz, VIN =12V, VOUT0-3 = 0.7V, IOUT0OUT3 = 31.25A per channel, VBIAS = 5.5V (RUNP: ON),
no forced airflow, no heatsink.

97.4

°C

Features and Benefits
· Quad digitally adjustable analog loops with a digital interface for control and monitoring. · Optimized for low output voltage ranges and fast load transient response. · 15mm × 22mm × 5.71mm Ball grid array (BGA) package.

EVAL-LTM4682-A1Z Evaluation Board

FILE

DESCRIPTION

EVAL-LTM4682-A1Z LTpowerPlay

Design files. Easy-to-use Windows® based graphical user interface (GUI) development tool.

DC1613A

The USB to PMBus controller dongle.

analog.com

Rev. 0 2 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

Quick Start
Required Equipment
· One power supply that can deliver 20V at 20A. · Four electronic loads that can deliver 35A at 0.7V each load. · Five digital multimeters (DMMs).

Procedure

The EVAL-LTM4682-A1Z evaluation board is easy to set up to evaluate the performance of the LTM4682. See Figure 2 for proper measurement equipment setup and use the following test procedures.

VOUT0
+

1m
+

LOAD 0 0A TO 31.25A

+
VIN

+
1m
+
VIN
4.5V TO 14V

LOAD 1
+ 0A TO 31.25A

VOUT1

VOUT2
+
+

+
VOUT3

1m
+

LOAD 2 0A TO 31.25A

LOAD 3 0A TO 31.25A

002

Figure 2. Proper Measurement Equipment Setup

1. With power off, connect the input power supply between VIN (TP9) and GND (TP10). Set the input voltage supply to 0V.
2. Connect the first load between VOUT0 (TP23) and GND (TP24), connect the second load between VOUT1 (TP20) and GND (TP21), connect the third load between VOUT2 (TP7) and GND (TP8), connect the fourth load between VOUT3 (TP5) and GND (TP6). Preset all the loads to 0A.
3. Connect the DMM between the input test points: VIN (TP1) and GND (TP11) to monitor the input voltage. Connect DMMs between VOUT0+ (TP16) and VOUT0- (TP17), VOUT1+ (TP18) and VOUT1- (TP19), VOUT2+ (TP12) and VOUT2- (TP14), VOUT3+ (TP13) and VOUT3- (TP15) to monitor the corresponding DC output voltages of Channel 0, Channel 1, Channel 2, and Channel 3. These output voltage test points are Kelvin sensed directly across COUT2 (Channel 0), COUT10 (Channel 1), COUT20 (Channel 2), and COUT29 (Channel 3) to provide an accurate measurement of output voltages. Do not apply load current to any of the above test points to avoid damage to the regulator. Do not connect the scope probe ground leads to VOUT0-, VOUT1-, VOUT2-, and VOUT3-.

analog.com

Rev. 0 3 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

4. Prior to powering up the EVAL-LTM4682-A1Z, check the default position of the jumpers and switches in the following positions.

SWITCH/JUMPER DESCRIPTION POSITION

SWR0, SWR1 SWR2, SWR3
RUN0, RUN1 RUN2, RUN3
OFF

P1 RUNP ON

P2 P17
WP_01 WP_23
OFF

5. Turn on the power supply at the input. Slowly increasing the input voltage from 0V to 12V (typical). Measure and ensure the input supply voltage is 12V and flip SWR0 (RUN0) and SWR1 (RUN1), SWR2 (RUN2), and SWR3 (RUN3) to the ON position. The output voltages should be 0.7V ±0.5% (typical) for VOUT0, VOUT1, VOUT2, and VOUT3.
6. Once the input and output voltages are properly established, adjust the input voltage between 6V to 14V max and the load current within the operating range of 0A to 31.25A max per channel. Observe the output voltage regulation, output voltage ripples, switching node waveform, load transient response, and other parameters. See Figure 3 for proper output voltage ripple measurement.
To measure the input/output voltage ripples properly, do not use the long ground lead on the oscilloscope probe. See Figure 3 for the proper scope probe technique. Short, stiff leads need to be soldered to the (+) and (-) terminals of an input or output capacitor. The probe’s ground ring needs to touch the (-) lead, and the probe tip needs to touch the (+) lead.
The output voltage ripples of Channel 0, Channel 1, Channel 2, and Channel 3 can also be monitored using on-board BNC terminals. Connect short BNC cables from VOUT0 (J3), VOUT1 (J4), VOUT2 (J5), and VOUT3 (J6) to the inputs of a 4-channel oscilloscope (scope probe ratio 1:1, AC-coupling) to observe output voltage ripples.

Figure 3. Scope Probe Placement for Measuring Output Ripple Voltage

(Option) Operation with VBIAS 7. The VBIAS pin is the 5.5V output of an internal buck regulator that can be enabled or disabled with RUNP. The VBIAS
regulator input is the VIN_VBIAS pin and is powered by VIN. The advantage of using VBIAS is bypassing the internal INTVCC_LDO powered from VIN, turning on the internal switch connected to the 5.5V VBIAS to INTVCC_01 and INTVCC_23 of the part, therefore, reducing the power loss, improving the overall efficiency, and lowering the temperature rise of the part when operating at high VIN and high switching frequency. The VBIAS must exceed 4.8V, and the VIN must be greater than 7V to activate the internal switch connecting VBIAS to INTVCC_01 and INTVCC_23 of the part. In typical applications, it is recommended that VBIAS is enabled.

Operation at Low VIN: 4.5V VIN 5.75V 8. Remove R31 to disconnect VIN_VBIAS from VIN. Remove C25. Set RUNP (P1) to the OFF position. Tie SVIN_01 to
INTVCC_01 by stuffing R142 with a 0 resistor. Tie SVIN_23 to INTVCC_23 by stuffing R143 with a 0 resistor. Make sure VIN is within 4.5V VIN 5.75V. Additional input electrolytic capacitors may be installed between VIN (TP9) and GND (TP10) to prevent VIN from drooping or overshoot to a voltage level that can exceed the specified minimum VIN (4.5V) and maximum VIN (5.75V) during large output load transient.

analog.com

Rev. 0 4 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

(Option) On-Board Load Step Circuit
9. The EVAL-LTM4682-A1Z evaluation board provides an on-board load transient circuit to measure VOUT peak-topeak deviation during rising or falling dynamic load transient. The simple load step circuit consists of two paralleled 40V N-channel power MOSFETs in series with two paralleled 10m, 2W, 1% current sense resistors. The MOSFETs are configured as voltage control current source (VCCS) devices; therefore, the output current step and its magnitude are created and controlled by adjusting the amplitude of the applied input voltage step at the gate of the MOSFETs. A function generator provides a voltage pulse between IOSTEP_CLK01 (TP22) and GND (TP2). The input voltage pulse should be set at a pulse width of less than 300µs and a maximum duty cycle of less than 2% to avoid excessive thermal stress on the MOSFET devices. The output current step is measured directly across the current sense resistors and monitored by connecting the BNC cable from IOSTEP_01 (J1) to the oscilloscope’s input (scope probe ratio 1:1, DC-coupling). The equivalent voltage to the current scale is 5mV/1A. The load step current slew rate di/dt can be varied by adjusting the rise time and fall time of the input voltage pulse. The load step circuit of Channel 0 or Channel 1 is connected to VOUT0 by default but can be used for VOUT1 by simply removing the 0 jumper R92 and stuffing it at the position of R93 and vice versa. Only one resistor, R92 or R93, can be stuffed at a time to avoid shorting VOUT0 and VOUT1 together. Repeat step 9 to perform load step transient evaluation for the VOUT1 rail. Similarly, load step transient evaluation of VOUT2 or VOUT3 can be performed using the same method described above. See the Schematics section for more details.

Connecting a PC to the EVAL-LTM4682-A1Z
Use a PC to reconfigure the digital power system management (PSM) features of the LTM4682, such as nominal VOUT, margin set points, overvoltage/undervoltage limits, output current and temperature fault limits, sequencing parameters, the fault logs, fault responses, GPIOs, and other functionality. The DC1613A dongle can be hot-plugged when VIN is present. See Figure 4 for the proper setup of the evaluation board.

INPUT POWER SUPPLY
VIN

USB CABLE
USB TO I2C/PMBus DONGLE
DC1613A

12-PIN CONNECTOR

LTM4682 EVALUATION BOARD EVAL-LTM4682-A1Z

VOUT0 VOUT1 VOUT2 VOUT3

LOAD0 LOAD1 LOAD2 LOAD3

Figure 4. EVAL-LTM4682-A1Z Evaluation Board Setup with a PC

004

analog.com

Rev. 0 5 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

LTpowerPlay Quick Start Guide
The LTpowerPlay is a powerful Windows-based development environment that supports Analog Devices digital power system management (PSM) ICs. The software supports a variety of different tasks. Use the LTpowerPlay to evaluate Analog Devices digital PSM µModule devices by connecting to an evaluation board system.
The LTpowerPlay can also be used in an offline mode (with no hardware present) to build a multichip configuration file that can be saved and reloaded anytime.
The LTpowerPlay provides unprecedented diagnostic tools and debug features. It becomes a valuable diagnostic tool during board bring-up to program or tweak the power management scheme in a system, or to diagnose power issues when bringing up rails.
The LTpowerPlay utilizes the DC1613A, USB-to-PMBus controller, to communicate with one of the many potential targets, including all the parts in the PSM product category evaluation system. The software also provides an automatic update feature to keep it current with the latest set of device drivers and documentation. Download and install the LTpowerPlay software at LTpowerPlay.
To access technical support documents for Analog Devices digital PSM products, visit the LTpowerPlay Help menu. Online help is also available through the LTpowerPlay interface.

analog.com

Figure 5. LTpowerPlay Main Interface Rev. 0 6 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

LTpowerPlay Procedure
Use the following procedure to monitor and change the settings for the LTM4682.
1. Launch the LTpowerPlay GUI. The GUI should automatically identify the EVAL-LTM4682-A1Z (see the following system tree).

2. A green message box shows for a few seconds in the lower left-hand corner, confirming that LTM4682 is communicating.
3. In the Toolbar, Click the R (RAM to PC) icon to read the RAM from the LTM4682. The configuration is read from the LTM4682 and loaded into the GUI.
4. Example of programming the output voltage to a different value. In the Config Tab, Click on the Voltage tab in the main menu bar, and type in 1V in the VOUT_COMMAND box as shown in the following figure.

analog.com

Rev. 0 7 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

5. Then, Click the W (PC to RAM) icon to write these register values to the LTM4682.

6. The output voltage will change to 1V. If the write command is successfully executed, the following message should be seen.

7. All user configurations or changes can be saved in to the NVM. In the Toolbar, Click the RAM to NVM icon.
8. Save the evaluation board configuration to a (*.proj) file. Click the Save icon and save the file with a preferred file name.

analog.com

Rev. 0 8 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

Typical Performance Characteristics

EFFICIENCY

POWER LOSS (W)

EFFICIENCY (%)

POWER LOSS

006

50 0

LOAD CURRENT (A)

Figure 6. Efficiency vs. Load Current, VOUT = 0.7V, ILOAD = 31.25A, VBIAS = 5.5V (RUNP: ON), fSW = 575kHz, SWR0: ON, SWR (1,2,3) OFF, VIN and VOUT Measured across CIN7 and COUT1, TA = 25°C, No Forced Airflow, No Heatsink

(a) No Forced Airflow

(b) Forced Airflow (200LFM)

Figure 7. Thermal Performance, VOUT = 0.7V, ILOAD = 31.25A per Channel, VBIAS = 5.5V (RUNP: ON), fSW = 575kHz, TA = 25°C, No Heatsink

analog.com

Rev. 0 9 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

008

VOUT 50mV/DIV AC-COUPLING
ILOAD 10A/DIV
100µs/DIV fSW = 575kHz, VOUT = 0.7V ILOAD-STEP = 15A TO 30A AT di/dt = 7.5A/µs VOUT(P-P) = 53mV OUTPUT VOLTAGE WAS MEASURED AT VOUT0 BNC (J3)
Figure 8. Load Transient Response
VOUT 50mV/DIV AC-COUPLING
50µs/DIV fSW = 575kHz, VOUT = 0.7V, ILOAD = 31.25A VOUT(P-P) = 17mV OUTPUT RIPPLE VOLTAGE WAS MEASURED AT VOUT0 BNC BNC CABLE WAS USED, 20MHz BWL
Figure 9. Output Ripple Voltage

009

analog.com

Rev. 0 10 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

EVAL-LTM4682-A1Z Evaluation Board Bill of Materials

QTY

REFERENCE

Required Circuit Components

4 C1, C18, C48, C50

4 C12, C17, C55, C56

1 C14

4 C2, C19, C49, C51

1 C25 2 C26, C27 2 C28, C33 2 C38, C41 4 C39, C40, C42, C43 1 C44 2 C65, C66

C67C70, CO1CO4,

CO10CO13, CO19CO22,

CO28CO31, CO37

12 C71C82 4 C84C87

4 C88C91

PART DESCRIPTION
CAP. CER 4700pF 50V 10% X7R 0603 DO NOT INSTALL CAP. CER 0.1F 16V 10% X7R 0603 CAP. CER 47PF 50V 5% C0G 0603 AEC-Q200 CAP. CER 1F 25V 10% X7R 0603 CAP. CER 2.2F 25V 10% X5R 0603 DO NOT INSTALL CAP. CER 4.7F 16V 10% X6S 0603 CAP. CER 1F 6.3V 20% X5R 0603 CAP. CER 22F 16V 10% X5R 1206 CAP. CER 100F 6.3V 10% X5R 1206
CAP. CER 100F 6.3V 20% X7S 1210
CAP. CER 0.1F 16V 20% X7R 0603 CAP. FILM 0.1F 16V 20% 0805 CAP. CER 0.01F 25V 5% C0G 0603 EXTREME LOW ESR

MANUFACTURER/PART NUMBER
YAGEO, CC0603KRX7R9BB472 TBD, TBD0805 KEMET, C0603C104K4RAC TDK, CGA3E2C0G1H470J080AA WURTH ELEKTRONIK, 885012206076 MURATA, GRM188R61E225KA12D TBD, TBD0603 MURATA, GRM188C81C475KE11D AVX CORPORATION, 06036D105MAT2A AVX CORPORATION, 1206YD226KAT2A MURATA, GRM31CR60J107KE39L
MURATA, GRM32EC70J107ME15L
VISHAY, VJ0603Y104MXJAP PANASONIC, ECP-U1C104MA5 KEMET, C0603C103J3GACTU

4 CIN1CIN4 10 CIN5CIN14

CAP. ALUM POLY 180F 25V 20% 8mm × 11.9mm 0.016 4650mA 5000h
CAP. CER 22F 25V 10% X7R 1210

PANASONIC, 25SVPF180M SAMSUNG, CL32B226KAJNNNE

CO5CO8,

CO14CO17, CO23CO26,

CO32CO35

2 D1, D2 4 D3D6 4 DS1, DS3, DS5, DS7 6 DS4, DS6, DS8DS11 6 J1J6

CAP. ALUM POLY 470F 2.5V 20% 2917
DIODE SCHOTTKY BARRIER RECTIFIER DO NOT INSTALL LED GREEN WATER CLEAR 0603 LED SMD 0603 COLOR RED AEC-Q101 CONN-PCB BNC JACK ST 50

PANASONIC, EEFGX0E471R
NEXPERIA, PMEG2005AEL, 315 DIODES INCORPORATED, TBD SOD323 WÜRTH ELEKTRONIK, 150060GS75000 VISHAY, TLMS1100-GS15 AMPHENOL CONNEX, 112404

3 P1, P2, P17

CONN-PCB 3-POS MALE HDR UNSHROUDED SINGLE ROW, 2mm PITCH, 3.60mm POST HEIGHT, 2.80mm SOLDER TAIL

SULLINS, NRPN031PAEN-RC

4 P7P10

DO NOT INSTALL (TBD) CONN-PCB INVISIPIN 0.64mm × 0.64mm STANDARD PIN

R&D INTERCONNECT SOLUTIONS, TBD

analog.com

Rev. 0 11 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

QTY

REFERENCE

1 P3

1 P4
1 P5
1 P6 4 Q1Q4 4 Q5, Q8, Q11, Q13
6 Q9, Q12, Q14Q17 R1R5, R7, R
18 66R73, R127, R133, R138, R146

PART DESCRIPTION
CONN-PCB 12-POS SHROUDER HDR, 2mm PITCH, 4mm POST HEIGHT, 2.5mm SOLDER TAIL
CONN-PCB 14-POS FEMALE HRD RA 2mm PITCH, 3mm SOLDER TAIL
CONN-PCB HDR 14POS 2.0mm GOLD 14mm × 4.3mm TH
CONN-PCB 4-POS SHROUDED HDR MALE 2mm PITCH
TRAN N-CH MOSFET 40V 14A
TRAN MOSFET N-CHANNEL ENHANCEMENT MODE
TRAN P-CHANNEL MOSFET 20V 5.9A SOT-23

MANUFACTURER/PART NUMBER AMPHENOL, 98414-G06-12ULF
SULLINS, NPPN072FJFN-RC MOLEX, 877601416 HIROSE ELECTRIC CO., DF3A-4P-2DSA VISHAY, SUD50N04-8M8P-4GE3 DIODES INCORPORATED, 2N7002A-7 VISHAY, SI2365EDS-T1-GE3

RES. SMD 10k 1% 1/10W 0603 AEC-Q200

PANASONIC, ERJ-3EKF1002V

R11R15, R23R27,

R46R50, R52, R54R59,

R79R85, R96R102,

R108R114, R121, R122,

R125, R126, R128, R131, R132, R134, R137, R140,

DO NOT INSTALL

R142, R143, R145, R149,

R150, R154, R155,

R163R166, R168R170,

R172R179

TBD, TBD0603

R86R90, R103R107, R116-R120

RES. SMD TBD R2512H35

4 R78, R91, R115, R123

DO NOT INSTALL

R124, R130, R136, R139, RES. SMD 301 1% 1/10W 0603

R144, R180R184

AEC-Q200

R8, R9, R17, R20, 12 R61R64, R129, R135,
R141, R147

RES. SMD 10 1% 1/10W 0603 AEC-Q200

R34, R37, R38, R41, R43, R148, R151R153, R156R162, R167, R171

RES. SMD 0 JUMPER 1/10W 0603 AEC-Q200

VISHAY, TBD2512H35 TBD, TBD2512 PANASONIC, ERJ-3EKF3010V VISHAY, CRCW060310R0FKEA
PANASONIC, ERJ-3GEY0R00V

R6, R16, R18, R19, 10 R21, R28, R51, R53,
R60, R65

RES. SMD 4.99k 1% 1/10W 0603 AEC-Q200

PANASONIC, ERJ-3EKF4991V

1 R22

RES. SMD 1.65k 1% 1/10W 0603 AEC-Q200

PANASONIC, ERJ-3EKF1651V

analog.com

Rev. 0 12 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

QTY

REFERENCE

4 R29, R30, R42, R44

3 R31R33

2 R35, R39

1 R45

4 R74R77 2 R92, R94 4 S1-S4

TP1TP4, TP11TP19, TP22, TP25TP57

PART DESCRIPTION DO NOT INSTALL RES. SMD 1 5% 1/10W 0603 AEC-Q200
RES. SMD 0.002 1% 1W 2512 AEC-Q200
RES. SMD 787 1% 1/10W 0603 AEC-Q200
RES. SMD 0.01 1% 2W 2512 AEC-Q200 RES. SMD 0 JUMPER 2512 AEC-Q200 SWITCH SLIDE DPDT 300mA 6V

MANUFACTURER/PART NUMBER TBD, TBD0805 PANASONIC, ERJ-3GEYJ1R0V
VISHAY, WSL25122L000FEA
PANASONIC, ERJ-3EKF7870V
VISHAY, WSL2512R0100FEA18 VISHAY, WSL251200000ZEA9 C & K, JS202011CQN

CONN-PCB SOLDER TERMINAL TEST POINT TURRET 0.094 MTG. HOLE PCB 0.062″ THK

MILL-MAX, 2501-2-00-80-00-00-07-0

TP5TP10, TP20, TP21, TP23, TP24

CONN-PCB THREADED BROACHING STUD 1032 FASTENER 0.625″, USE ALT_SYMBOL FOR CAPTIVE FASTENER, CKFH1032-10 C450D200 PAD

1 U1

IC-ADI LOW VOUT QUAD 31.25A OR SINGLE 125A µModule REGULATOR WITH DIGITAL POWER SYSTEM MANAGEMENT, PRELIM

ANALOG DEVICES, LTM4682

1 U3

IC EEPROM 2K-BIT I2C SERIAL EEPROM 400kHz

Hardware: For Evaluation Board Only

STANDOFF, SELF-RETAINING SPACER, 12.7mm LENGTH

MICROCHIP TECH., 24LC025-I/ST WURTH ELEKTRONIK, 702935000

CONNECTOR RING LUG TERMINAL, 10 CRIMP, NO INSULATED

KEYSTONE, 8205

WASHER, #10 FLAT STEEL

KEYSTONE, 4703

NUT, HEX STEEL, 10-32 THREAD, 9.27mm OUT DIA

KEYSTONE, 4705

SHUNT, 2mm JUMPER WITH TEST POINT

Optional Evaluation Board Circuit Components

CO9, CO18, CO27, CO36

CAP. ALUM POLY 7343-20

2 Q7, Q10 2 R93, R95 2 R36, R40

TRAN P-CHANNEL MOSFET 20V 5.9A SOT-23 RES. SMD 0 JUMPER 2512 AEC-Q200 RES. SMD 0.002 1% 1W 2512 AEC-Q200

WURTH ELEKTRONIK, 60800213421
PANASONIC, EEFGX0E471R VISHAY, SI2365EDS-T1-GE3 VISHAY, WSL251200000ZEA9 VISHAY, WSL25122L000FEA

analog.com

Rev. 0 13 of 18

Evaluation Board User Guide
EVAL-LTM4682-A1Z Schematics

EVAL-LTM4682-A1Z

analog.com

Rev. 0 14 of 18

Evaluation Board User Guide
EVAL-LTM4682-A1Z Schematics (continued)

EVAL-LTM4682-A1Z

analog.com

Rev. 0 15 of 18

Evaluation Board User Guide
EVAL-LTM4682-A1Z Schematics (continued)

EVAL-LTM4682-A1Z

analog.com

Rev. 0 16 of 18

Evaluation Board User Guide

EVAL-LTM4682-A1Z

Ordering Information

PART

TYPE

EVAL-LTM4682-A1Z

The EVAL-LTM4682-A1Z evaluation board features the LTM4682, quad output regulator with digital power system management (PSM). The EVAL-LTM4682-A1Z evaluation board is configured as a 4-phase four outputs.

Revision History

REVISION NUMBER
0

REVISION DATE
03/25 Initial release

DESCRIPTION

PAGES CHANGED
—

analog.com

Rev. 0 17 of 18

Evaluation Board User Guide
Notes

EVAL-LTM4682-A1Z

ALL INFORMATION CONTAINED HEREIN IS PROVIDED “AS IS” WITHOUT REPRESENTATION OR WARRANTY. NO RESPONSIBILITY IS ASSUMED BY ANALOG DEVICES FOR ITS USE, NOR FOR ANY INFRINGEMENTS OF PATENTS OR OTHER RIGHTS OF THIRD PARTIES THAT MAY RESULT FROM ITS USE. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. NO LICENSE, EITHER EXPRESSED OR IMPLIED, IS GRANTED UNDER ANY ADI PATENT RIGHT, COPYRIGHT, MASK WORK RIGHT, OR ANY OTHER ADI INTELLECTUAL PROPERTY RIGHT RELATING TO ANY COMBINATION, MACHINE, OR PROCESS, IN WHICH ADI PRODUCTS OR SERVICES ARE USED. TRADEMARKS AND REGISTERED TRADEMARKS ARE THE PROPERTY OF THEIR RESPECTIVE OWNERS. ALL ANALOG DEVICES PRODUCTS CONTAINED HEREIN ARE SUBJECT TO RELEASE AND AVAILABILITY.

analog.com

Rev. 0 18 of 18

Documents / Resources

ANALOG DEVICES EVAL-LTM4682-A1Z Evaluation Board [pdf] User Guide
EVAL-LTM4682-A1Z, EVAL-LTM4682-A1Z Evaluation Board, EVAL-LTM4682-A1Z Board, Evaluation Board, Board

References

User Manual

EVAL-LTM4682-A1Z Evaluation Board

Product Information

Specifications

Product Usage Instructions

Setting Up the Evaluation Board

Adjusting Voltages and Load Current

Observing Parameters

FAQ

Q: What is the default input voltage range for the
EVAL-LTM4682-A1Z board?

Q: What is the maximum load current per channel supported by
the board?

Q: How can the output voltage be adjusted on the evaluation
board?

Documents / Resources

References

Leave a comment

Cancel reply