AMPTRON AT-SOLCHR-AM2430PV01 30A inLine MPPT Solar Charge Controller
We may modify these specifications without prior notice.
Main Features
- MPPT solar charge controller designed for portability.
- 3-stage charging optimises battery performance.
- Supports battery types GEL / AGM / LiFePO
- LCD showing Battery Voltage and Charge Current.
- User-friendly key press operation.
- Easy mounting and storage.
- Designed for the Amptron 200W Solar Blanket
(AT-SOLBLANK-19.4-200-BV10) - Over-charge, Over-temperature, Reverse polarity protections.
- Genuine Anderson connectors.
Warnings
- Designed for 12V/24V batteries, do not connect to battery voltages higher than this.
- Use within rated power and voltage range.
- Keep controller away from water.
- Keep controller away from excessive heat sources.
Operating range is 20°C to +55°C - Avoid direct sunlight.
- Keep space around the controller for good heat dissipation.
PRODUCT DIMENSIONS
Wire Dimension
SPECIFICATION
| Parameters | Value |
| No load loss | 20mA @ 12V
12mA @ 24V |
| System Voltage | 12V/24V |
| Battery Type | AGM /GEL/ LiFePO4 |
| Max Solar Input Voltage | 30V VOC (12V Battery) 50V VOC (24 V Battery) |
| Rated Solar Charge Current | 30A |
| Max Solar Input Power | 12V- SOW
24V-900W |
| Operating Temperature | -20°(C to +45°C |
| Internal Temperature Protection | -40°C to +80°C |
| IP Protection | IP45 |
| Net Weight | 350g |
| Dimensions | 150 x 80 x 35.3mm |
INSTALLATION GUIDE
Note:
First connect the battery, then connect the Solar panel.
LCD Instructions
- LCD Display Indication
- Battery SOC Indication
KEY OPERATION
SETTING BATTERY TYPE
Setting Battery Type / Voltage
Lead-acid batteries are selected automatically, and generally do not need to be set.
Lithium batteries need to be set as follows:
- First, hold the button for 3 seconds, the battery type indicator will flash.
- Then short press to enter the next battery type.
- When your battery type is highlighted, long press the button for 3 seconds. At this time the display screen will show a battery voltage 12V LFP.
If you want to set 24V, short press the button and it will switch to 24V LFP. - Finally, long press the button for 3 seconds to save your parameters.
Warnings and General Comments
Solar Panels:
It’s recommended to use nominal 18V panel for 12V batteries and 36V panels (single 36V panel or 2 units of 18V panels in series) for 24V batteries.
- Do not exceed PVVOC (Voltage Open Circuit). The PV VOC cannot exceed 30V for 12V batteries or 50V for 24V batteries to prevent product damage.
- Charging start condition: PV voltage needs to be 3V higher than battery voltage for charging to start.
Eg: PV minimum charging voltage is at 12V, or higher than 27V when voltage is at 24V. - In addition battery voltage should be higher than 3V.
- Avoid placing solar panels in partially sunny or shaded environments for best performance.
- Keep controller away from water.
- Avoid direct sunlight on the charge controller.
Error Code:
Bluetooth App
A Bluetooth app is available for real-time monitoring of your system. Please search for ‘Charge Pro 2.0’ or scan the relevant QR code below.
For product support and troubleshooting that is outside the above advice, please contact us via email: support@amptron.com.au
Documents / Resources
 |
AMPTRON AT-SOLCHR-AM2430PV01 30A inLine MPPT Solar Charge Controller [pdf] User Manual AM2430PV01, AM2420P, AT-SOLCHR-AM2430PV01 30A inLine MPPT Solar Charge Controller, AT-SOLCHR-AM2430PV01, 30A inLine MPPT Solar Charge Controller, MPPT Solar Charge Controller, Solar Charge Controller, Charge Controller, Controller |