iQ Low Voltage Smart Transformer
“
Product Information
Specifications
- Model: Smart Platform Transformer
- Input: 120VAC, 60Hz, 3A
- Output: 15VAC
- Max. Rating: 300W
Product Usage Instructions
Safety Guidelines
Low voltage installation and maintenance are safe, but
regulations should be followed. Ensure compliance with safety
regulations for a safe installation.
Package Contents
- (1) Transformer
- (1) Hanger
- (1) Pin
Determine the Load
Prior to installation, determine the total wattage of all
fixture lamps. Make sure the total wattage is 20% less than the
transformer’s capacity to avoid overloading.
Parts Required (Sold Separately)
- (2) Wall Anchors
- (2) Screws
Installation Steps
Step 1 – Install Hanger
Attach the hanger to the back of the transformer using screws
and lift it up to hold screws in place.
Step 2 – Mount Transformer
Mount the transformer on the wall using wall anchors and
screws.
Step 3 – Open the Door
Release the locking hasp on the transformer to open the door for
further installation.
Step 4 – Install Conduit Adapter
Remove the knock-out on the bottom of the transformer and
install the conduit adapter and flexible cord connector.
Step 5 – Wiring Fixture Wires
Pass fixture supply cables through one conduit and insert them
into the transformer. Connect supply wires to terminal blocks as
instructed.
Frequently Asked Questions (FAQ)
Q: What should I do if I exceed the transformer’s
capacity?
A: If you exceed the transformer’s capacity, consider using a
secondary or larger transformer for your installation.
Q: Can I use supply wires larger than 12AWG?
A: No, connect maximum 12AWG supply wires to the side terminal
blocks as instructed in the manual.
“`
R
LOW-VOLTAGE SMART TRANSFORMER
INSTALLATION GUIDE
Model:
Smart Platform Transformer
ATTENTION:
Please read this installation guide carefully to ensure safe and efficient operation of this Power
Supply
SAFETY GUIDELINES
Low voltage installation and maintenance is safe and presents no risk for electric shock injury. However, there are regulations that may apply and that should be followed by installers. The following safety points may or may not be included in these regulations – the installer is responsible for ensuring a compliant installation.
· WARNING- RISK OF SHOCK. Install power unit at least 5 feet (1.5m) from pool or spa and at least 10 feet (3.05m) from a fountain.
· WARNING- install power unit in or on non-combustible materials only.
· Power supply must be connected (using supplied power cord) to GFCI-protected receptacle with an In-use cover.
· All power supplies are indoor and outdoor rated, but we recommend that the transformer be mounted outdoors. If mounting indoors, check for local electrical codes that may apply.
· Power supply must be mounted in a vertical orientation with the bottom plate at least 1 foot above the ground.
· In hot climates, avoid mounting in direct sunlight.Power unit will get hot regardless of climate. This is normal for operation.
www.amplighting.com
WARNING!!!
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications n ot expressly a pproved by t he party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Statement The distance between user and products should be no less than 20cm.
Open the shipping carton and carefully remove the transformer, accessories, and hardware. Inspect contents for any damage that may have occured during shipping.
PACKAGE CONTENTS
A. (1) Transformer B. (1) Hanger C. (1) Pin
www.amplighting.com
DETERMINE THE LOAD
The general capacity should have been determined prior to purchasing the transformer. Circuit loads should not exceed 80% of capacity. As a general rule, total light fixture wattage should not exceed 80% of the transformer capacity. To determine the total wattage, simply add up the wattage of all fixture lamps. This number should be 20% less than the transformer’s wattage capacity. If you are over capacity, your installation may require a secondary or larger transformer.
PRODUCT DIMENSIONS
R0.16″
6.66″ 6.13″
5.63″
R0.12″
13.05″
12.68″
13.64″
www.amplighting.com
PARTS REQUIRED (SOLD SEPARATELY)
A. (2) Wall Anchors B. (2) Screws
START HERE
STEP 1 – INSTALL HANGER
Attach the large holes on the hanger to screws on the back of the transformer and then lift up the hanger to hold screws in the slots.
www.amplighting.com
Screw
Hanger
Large Hole on the Hanger Back of Transformer
Hanger Slot
STEP 2 – MOUNT TRANSFORMER
Determine the desired location for mounting the transformer. The transformer must be mounted in a vertical orientation with the bottom plate at least 1 foot above the ground. Mark the desired location using the top and bottom keyhole as a guide. Drill holes on the marks and insert the wall anchors. Thread the screw into the top keyhole. Leave enough of the screw out so that the transformer can hang on it. Hang the top keyhole onto the screw, then place a screw through the bottom keyhole. Secure both the bottom and top screw using a screwdriver.
www.amplighting.com
Wall Anchor
Screw Top Keyhole
Transformer
Wall Anchor Bottom Keyhole
1 Foot Min.
Screw
Ground
STEP 3 – OPEN THE DOOR
Release the locking hasp on the transformer to open the door.
www.amplighting.com
Transformer
Transformer
Locking Hasp
Door
MOIMnAupotXudpt.eu:Rlt1::A2S1T05MIVVN-AAAGCTC:R,36-03000HW0z-,S3SA
POWER
Wi-Fi
Bluetooth
Hardware Reset
Wi-Fi Reset
Main Power
OLuotwpu-Vt oPlotawgeer
COM 15V
COM 15V
STEP 4 – INSTALL CONDUIT ADAPTER
Remove the knock-out on the bottom of the transformer. Install the conduit adapter and flexible cord connector to the transformer.
www.amplighting.com
Model: SM-ATR-300-SS Input: 120VAC, 60Hz, 3A Output: 15VAC MAX. RATING: 300W
POWER
Wi-Fi Bluetooth
Hardware Wi-Fi
Reset
Reset
Main Power
Low-Voltage Output Power
Transformer
COM 15V
COM
15V
Flexible Cord Connector
Knock-Out Conduit Adapter
STEP 5 – WIRING FIXTURE WIRES
Pass fixture supply cables through one conduit and insert them into the transformer. Strip both ends of each supply wires. The supply wires can be connected to either side terminal blocks or middle terminal blocks.
1. Connect maximum 12AWG supply wires to side terminal blocks: Open the lever and insert one of the fixture wire into the COM block and the other wire from the same fixture into the 15V block. Close the levers to lock the inserted wires into place.
2. Connect maximum 2AWG supply wires to middle terminal blocks: By using a screwdriver, loosen the screws on the middle terminal blocks and insert one of the fixture wire into the COM block and the other wire from the same fixture into the 15V block. Tighten the screws until the insert wires are locked into place.
www.amplighting.com
Middle Terminal Block (2AWG Max.)
Transformer
Side Terminal Block
(12AWG Max.)
Transformer
POWER Wi-Fi Bluetooth
Hardware Wi-Fi Reset Reset
POWER Wi-Fi Bluetooth
Hardware Wi-Fi Reset Reset
Main Power
Low-Voltage Output Power
Main Power
Low-Voltage Output Power
Lever
COM 15V
COM
15V
To 15 VAC Fixutre
Conduit
Screw
COM 15V
COM
15V
Apply Duct Seal to seal against moisture
STEP 6 – CLOSE THE DOOR
Close the door and lock it by using the locking hasp.
www.amplighting.com
Transformer
Model: SM-ATR-300-SS Input: 120VAC, 60Hz, 3A Output: 15VAC MAX. RATING: 300W
POWER Wi-Fi Bluetooth
Hardware Wi-Fi Reset Reset
Main Power
Low-Voltage Output Power
COM 15V
COM
15V
Transformer Locking Hasp
Door
Locking Hasp
STEP 7 – CONNECT TO OUTLET
Insert the plug from the transformer into the outlet.
Outlet
Plug from Transformer
INDICATORS / BUTTONS DESCRIPTIONS
POWER Wi-Fi Bluetooth
Hardware Wi-Fi Reset Reset
Main Power
Low-Voltage Output Power
On the right, there is a table for indicators / buttons descriptions.
www.amplighting.com
No. 1 2 3 4 5 6
7
Indicator/ Button
POWER
Wi-Fi
Bluetooth
Hardware Reset
Description
Power Indication Light (Green) – ON: Power is ON. – OFF: No power. Check connection.
Wi-Fi Indication Light (Green) – FLASH: Setup mode. – ON: Connected to Wi-Fi network. – OFF: No Wi-Fi Connection.
Bluetooth Indication Light (Blue) – ON: Bluetooth mesh is up and running. – OFF: Bluetooth mesh is not active; transformer is only providing power.
Hardware Reset Button – Press and hold for seven (7) seconds to reset Transformer.
Wi-Fi Reset
Wi-Fi Reset Button – Press and release to re-establish Wi-Fi communications.
Main Power – Press to turn ON / OFF the transformer.
Low Voltage Output Power (Over-current Protection Switch) – This switch should be in the ON position during normal operation. When an over-current condition exists, the switch automatically turns OFF to remove power to the fixtures. After reducing the circuit load appropriately, the switch must be placed in the ON position, and the fixtures will resume normal operation.
HOW TO CONNECT TRANSFORMER TO INTERNET?
1. Download and install the APP “AMP iQ” in your smartphone from
Google Player Store
or Apple Store .
2. Ensure Bluetooth is enabled on your mobile device.
Settings
Bluetooth
Bluetooth
Allow New Connections
New Bluetooth connections have been turned off from Control Center.
MY DEVICES Volt-f4e6
Not Connected
Not Connected
OTHER DEVICES
Bluetooth
Bluetooth Device Name CONNECTED DEVICES
OTHER DEVICES
Help
Scan Devices
iPhone Bluetooth Android Bluetooth
Settings
Settings
www.amplighting.com
3. Open the APP “AMP iQ” , click “+” on the top
user
right corner.
Home
4. Click ” Add Transfomer”.
user
Home
Add Transformer
Press the + in the top right corner to add a transformer.
Add Fixture
Create Group
Add Transformer
Home
Cancel Fixtures
Schedules
Add Transformer
Press the + in the top right corner to add a transformer.
Home
Fixtures
Schedules
5. Click “I’m Ready”.
Connect Transformer To connect a AMP Field transformer, make sure you are nearby and have easy access to
it.
I’m Ready Cancel
Bluetooth
Place your AMP Field transformer in pairing mode by pressing the Pair button for 5 seconds.
6. Click “Proceed”.
Proceed
www.amplighting.com
7. The App may take a few seconds to discover the transformer.
Searching for Nearby Transformers
8. Select the discovered Transformer and then
Select Transformer
pair to the bluetooth
f4e6
until it is successfully
Cancel
connected.
Re-scan
9. Click “Search for Wi-Fi Networks” to find the available Wi-Fi networks nearby.
Connected to Transformer
Next we’ll connect your transformer to your Wi-Fi network.
Connected to Transformer
Next we’ll connect your transformer to your Wi-Fi network.
Search for Wi-Fi Networks
Cancel Search for Wi-Fi Networks
www.amplighting.com
10. Select a network and enter the network password to connect the Transformer. A successful connection may take a few seconds. *** Note: The AMP iQ Transformer operates only on 2.4 GHz Wi-Fi networks. ***
Select a Network 2.4 GHz Wi-Fi connection is required. Wi-Fi1 Wi-Fi2 Wi-Fi3
Wi-Fi1 Connect Transformer
Help Re-scan Networks
Cancel Connecting
11. Name your transfomer with a distinctive name for easy identification later. Click “Save” after entering names.
12. Note: Steps 12 through 15 are for Apple iPhones only. If you are using an Android phone, you may proceed directly to Step 16. iPhone users must manually forget the Transformer from the phone’s Bluetooth connections. To do so, press “Continue to Settings”. If the Bluetooth Connection to the Transformer has already been forgotten, then click “I have forgotten the device”.
As a next step in the onboarding process Please forgot the device from the bluetooth device list in the device settings
Settings
Bluetooth
Bluetooth
Allow New Connections
New Bluetooth connections have been turned off from Control Center.
MY DEVICES
Not Connected
Not Connected
Bluetooth Forget This Device
Bluetooth Forget This Device
OTHER DEVICES
Step 1
Step 2
Forget Device Cancel
Step 3
Continue to Settings I have forgotten the device
Name Your Transformer AMP Light-abdrew1
If using multiple transformers, consider giving each one a distinctive name, such as Front Yard
and Back Yard, for easy identification later. Asia/Shanghai
Save
www.amplighting.com
13. In the Bluetooth settings screen of your iPhone, find the Transformer you just connected and click on the blue “i” on the right.
14. Click “Forget This Device” to remove the Transformer from the blutooth device list.
Bluetooth Forget This Device
Bluetooth Forget This Device
Settings
Bluetooth
Bluetooth
Allow New Connections New Bluetooth connections have been turned off from Control Center.
MY DEVICES Not Connected
Not Connected
OTHER DEVICES
Forget Device Cancel
15. Go back to the “AMP iQ” window and click “I have forgotten the device”.
16. Wait a few seconds for the Transformer to connect to the Bluetooth mesh.
As a next step in the onboarding process Please forgot the device from the bluetooth device list in the device settings
Settings
Bluetooth
Bluetooth
Allow New Connections New Bluetooth connections have been turned off from Control Center.
MY DEVICES Not Connected
Not Connected
Bluetooth Forget This Device
Bluetooth Forget This Device
OTHER DEVICES
Step 1
Step 2
Forget Device Cancel
Step 3
Continue to Settings I have forgotten the device
Connecting Transformer to Mesh
Cancel Continue
www.amplighting.com
17. When the Transformer setup is complete, click “Next” to add fixtures or operate the system.
Transformer Setup Complete
Next
R
15486 N. Nebraska Avenue Lutz, FL 33549 1-813-978-3900 www.amplighting.com
Documents / Resources
 |
AMP iQ Low Voltage Smart Transformer [pdf] Installation Guide SM-ATR-300-PGR, 2AI4GSM-ATR-300-PGR, 2AI4GSMATR300PGR, iQ Low Voltage Smart Transformer, iQ, Low Voltage Smart Transformer, Smart Transformer, Transformer |