AMC iAC120DSP Power Amplifiers DSP Dante Cards
Product Information
Specifications
- iAC 120 DSP
- Output power: 1 x 120 W
- Power consumption: 180 VA
- Stand by power consumption: 10 VA
- Frequency Response (100 V): 32 Hz – 21 kHz
- THD: 0.07%
- S/N ratio: 95 dB
- Input sensitivity: N/A
- Input impedance: N/A
- Cooling: Passive cooling
- Dimensions (H x W x D): 44 x 430 x 245 mm
- Weight: 5 kg
- iAC 240 DSP
- Output power: 1 x 240 W
- Power consumption: 360 VA
- Stand by power consumption: 10 VA
- Frequency Response (100 V): 120 Hz – 20 kHz
- THD: 0.20%
- S/N ratio: 92 dB
- Input sensitivity: N/A
- Input impedance: N/A
- Cooling: Forced air cooling with manual/auto control
- Dimensions (H x W x D): 88 x 430 x 342 mm
- Weight: 9.4 kg
- iAC 360 DSP
- Output power: 1 x 360 W
- Power consumption: 540 VA
- Stand by power consumption: 10 VA
- Frequency Response (100 V): 31 Hz – 20 kHz
- THD: 0.25%
- S/N ratio: 98 dB
- Input sensitivity: N/A
- Input impedance: N/A
- Cooling: Forced air cooling with manual/auto control
- Dimensions (H x W x D): 88 x 430 x 342 mm
- Weight: 11.5 kg
- iAC 2X240 DSP
- Output power: 2 x 240 W or 1 x 480 W
- Power consumption: 720 VA
- Stand by power consumption: 20 VA
- Frequency Response (100 V): 35 Hz – 21 kHz
- THD: 0.16%
- S/N ratio: 94 dB
- Input sensitivity: N/A
- Input impedance: Balanced – 11 k, unbalanced – 8 k
- Cooling: Forced air cooling with manual/auto control
- Dimensions (H x W x D): 88 x 430 x 342 mm
- Weight: 8 kg (for single channel), 9.4 kg (for dual channel)
Introduction
Single and two channel Class-D amplifiers for 100 V and low impedance systems. Electronically controlled amplifier circuit, easy menu navigation with rotary controller and LCD. Silent fan mode, DSP processing: 6-point parametric EQ, limiter, gate, delay. Balanced Phoenix & Stereo RCA inputs and audio link outputs. RS-232 port for full control and status feedback allows integrating iAC amplifiers into large and complex audio systems that can be automated or controlled remotely. iAC 2×240 DSP features internal input-output routing and bridging. All models are available with an optional Dante card for use with digital audio network systems.
Technical Specifications
| Technical Specifications | iAC 120 DSP | iAC 240 DSP | iAC 360 DSP | iAC 2X240 DSP |
| Output power | 1 x 120 W | 1 x 240 W | 1 x 360 W | 2 x 240 or 1 x 480 W |
| Power consumption | 180 VA | 360 VA | 540 VA | 720 VA |
| Stand by power consumption | 10 VA | 10 VA | 10 VA | 20 VA |
| Power supply | ~ 230 V, 50 Hz | |||
| Outputs | 1 x Phoenix power output, 1 x Phoenix audio link | |||
| Inputs | 1 x Balanced Phoenix, 1 x Stereo RCA Optional: Dante digital audio 1 x RJ-45 | |||
| Frequency Response (100 V) | 120 Hz – 20 kHz | |||
| Frequency Response (4 ohm) | 32 Hz – 21 kHz | 31 Hz – 20 kHz | 31 Hz – 20 kHz | 35 Hz – 21 kHz |
| THD | 0,07 % | 0,20 % | 0,25 % | 0,16 % |
| S/N ratio | 95 dB | 92 dB | 98 dB | 94 dB |
| Input sensitivity | ||||
| Input impedance | Balanced: 11 kΩ, unbalanced 8 kΩ | |||
| Remote control | RS-232 | |||
| Tone control (over RS-232) | 6-band parametric EQ | |||
| Cooling | Passive cooling | Forced air cooling with manual / auto control | ||
| Dimensions (H x W x D) | 44 x 430 x 245 | 88 x 430 x 342 | ||
| Weight | 5 kg | 8 kg | 9.4 kg | 11.5 kg |
contact
AMC® BALTIC Neries kr. 14A, LT-48397, Kaunas, Lithuania / (370 37) 308585/www.amcpro.eu
Documents / Resources
 |
AMC iAC120DSP Power Amplifiers DSP Dante Cards [pdf] Installation Guide iAC120DSP Power Amplifiers DSP Dante Cards, iAC120DSP, Power Amplifiers DSP Dante Cards, Amplifiers DSP Dante Cards, DSP Dante Cards, Dante Cards, Cards |