AMBIENTECH TECH-WSx-SA Wall Switch
Wall Switch Installation
Wall Box
- A standard single-gang wall box sized 3 x 2 x 2 ½ cm will service Dimmer
- Not compatible with multi or double Mud Rings.
- When using a retrofit gang box (cut in box) you might need to recess the ears.
Maximum Load
| Input Voltage | Max Load |
| 120VAC | 700W |
Note: A maximum of 7 Drivers can be controlled w ith each Wall Sw itch
Before You Begin
To avoid fire, shock, or death, turn the power Off at circuit breaker and test to ensure the power is Off before wiring.
Step l: Prepare Wall Box Wires
- Make sure that the ends of the w ires from the wall box are straight (cut if needed).
- Strip the wire insulator for each wire inside the wall box as shown here:
Step 2: Wire Wall Switch
Connect wires according to the wiring diagram below.
Wiring Description (Using wire connectors)
- Connect the green (or bare copper) wire from the wall box to the green Wall Switch wire.
- Connect the line/hot wire from the wall box to the black Wall Switch wire.
- Connect the black LED Driver wire to the red Wall Switch wire.
- Connect the white wire from the wall box to the white LED Driver wire and the white Wall Switch wire.
Step 3: Mount the Wall Switch
Mount the Wall Switch into the wall box using the screws provided.
Step 4: Restore Power
- Turn the power On at the circuit breaker.
- Verify 120V with a Voltmeter
Item Identification
- Mounting Screws
- Wire Connectors
- Cover Plate
- Wall Switch
Pairing
If you are installing more than one Wall Switch unit, all others must be switched Off while pairing.
- Make sure both sliders are set to the top and the Wall Switch is switched Off.
- Switch the power On at the circuit breaker.
- Turn On the Wall Switch, the green LED Indicator will blink while pairing.
- After up to lS seconds, your LED fixture will be paired with the Wall Switch.
- To verify pairing is successful, move the sliders and ensure that the LEDs respond accordingly.
- If you re installing a smart wall switch Scan the QR code to download the app. Follow the instructions to connect to the SmartAir App.
* If pairing is not successful press the Wall Switch pairing/ reset button.
Connect to the SmartAir App
- Scan the QR code to download the App. Follow the instructions to connect to the SmartAir App
Operation – Dimmer Wall Switch
Customer Assistance
For technical questions regarding the installation or operation of this product, please contact our customer support team:
347-334-6368 ext 3
www.ambientechinc.com
Caution
To reduce the risk of overheating and possible damage to other equipment, do not install to control a receptacle, A motor-operated appliance, or a transformer-supplied appliance.
“GRADATEURS COMMANDANT UN BALLAST – AFIN DE REDUIRE LE RISQUE DE SURCHAUFFE ET LA POSSIBILITE D’ENDOMMAGEMENT A D’AUTRES MATERIELS, NE PAS INSTALLER POUR COMMANDER UNE PRISE, UN APPAREILA MOTEUR,”
FCC/IC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Troubleshooting
| Symptoms | Cause | Possible Solution |
| Wall Switch LED Indicator blinking RED | The pairing/ reset button is pressed while the wall switch is off | Turn ON the Wall Switch and press the Pairing button again |
| Wall Switch LED Indicator steady RED | The Wall Switch is trying to perform pairing | Turn On the
Wall Switch until paring is completed |
| Lights do not respond to Wall Switch | The Breaker is Off, or tripped Improper pairing | Turn power On at the Circuit breaker Perform “Pairing” |
| Improper wiring | Make sure all wires are connected according to the wiring diagram | |
| Short circuit at the LED Driver output | Check LED Driver output for short circuits | |
| The wall switch is | The Wall Switch was | Perform “Pairing”. |
| controlling | paired with the | Make sure all the other |
| the wrong lights | wrong LED Driver | Wall Switches are turned |
| (Only if multiple | Off while pairing | |
| Wall Switches units are | ||
| installed in the | ||
| same location) | ||
| Wall Switch/ LED Driver | Any reason | Perform “Pairing”. |
| Replacement | Make sure all the other | |
| Wall Switches are | ||
| turned Off while | ||
| pairing |
Documents / Resources
 |
AMBIENTECH TECH-WSx-SA Wall Switch [pdf] Instruction Manual TECH-WSx-SA Wall Switch, TECH-WSx-SA, Wall Switch, Switch |
