ALUX ALC-C-95 Coding Rider Drone Camera User Guide
Part Names
Propeller Configuration
A Clockwise Rotation
B Counter-clockwise Rotation
Controller Description
Instructions
Calibrating the Position Sensor
The attitude sensor is the sensor that allows the drone to fly in the correct orientation without tilting. If your drone is not flying in the correct orientation or is tilting, perform an attitude sensor calibration to compensate for the sensor.
With the drone and controller paired,
press and hold the S button (calibration button) on the controller for at least 3 seconds.
If the controller beeps and the drone’s main LED blinks and then lights up, the calibration is successful.
Calibrating the Controller Levers
The controller lever calibration is to calibrate the left and right levers of the controller. If the drone’s behavior is not consistent with the movement of the levers when you fly the drone, perform the controller lever calibration.
Press and hold the 5 button (calibration button) o n the controller for at least 3 seconds while the drone and controller are unpaired (battery is removed from the drone).
If the controller beeps once or twice, the calibration is successful.
Basic Flight
Ascend/Descend
Move the left lever on the controller up to ascend the drone, and down to descend. This is the same as the lever operation for takeoff and landing.
Left/Right Turns
Move the left lever on the controller to the left to turn the drone left, and to the right to turn it right.
Forward/Reverse
Move the right lever on the controller up to move the drone forward, and down to move it backward.
Left/Right Movement
Move the right lever on the controller to the left to move the drone left, and to the right to move it right.
Change Control Mode
Press and hold the Trim button for at least 3 seconds during landing.
Button (1 buzzer): Mode 1
Button (2 beeps): Mode 2
Throttle: Climb & Descend
Yaw: Turn Left & Right
Pitch: Forward & Backward
Roll: Move left & right
The default setting is Mode 2
Headless Mode
Press and hold for 3+ seconds
When the drone is landed, press and hold the A button (headless mode button) between the levers on both sides of the controller for more than 3 seconds to set the drone to headless mode.
2 beeps: Headless mode is set
1 buzzer: Headless mode off
Headless mode Flight direction is fixed to the direction of the drone’s landing,
The LEDs on the side LED indicators on both sides of the controller will blink when in headless mode.
Heading Reset
While the drone is in headless mode, a short press of the A button (Heading Reset button) between the levers on either side of the controller will reset the drone’s heading as shown in the figure to the left. If the drone lands and then takes off again, the heading will be reset to the direction of the drone’s landing.
Heading Reset only works when neither lever on the controller is operated.
Trim Setting
When the dronies flight and muse ska ordain fiction without any control use the “rinse Setting” button on the controller to cure the flow Thecoma lee beeps-cattie the broom Set button is preset and sig beeping when the non setting ends maximum.
- Press the
button on the Trim setting button to stop the forward movement. - Press the
button of the Trim setting button to stop the backward movement.
- If it is moving to the left, press the button on the Trim settings button to stop it. button on
- If it is moving to the right, press the button the Trim settings button to stop it.
Except for initial defects, any other use, negligence and damage will result in a chargeable repair.
Precaution & Maintenance
- Do not tamper with the structure of this product.
- Recycle the battery or battery pack or dispose of it properly in accordance with waste disposal laws.
- Do not throw or drop the product.
- Read and understand the product manual carefully.
- If the product is disassembled by the user, it may not be eligible for normal product warranty service.
Warranty
Except for initial defects, any other use, negligence and damage will result in a chargeable repair,
Other detailed product repairs and support are subject to the terms and conditions of sale of the dealer. Please contact the dealer for more information.
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Compliance Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
Documents / Resources
 |
ALUX ALC-C-95 Coding Rider Drone Camera [pdf] User Guide ALC-C-95, ALC-C-95 Coding Rider Drone Camera, Coding Rider Drone Camera, Rider Drone Camera, Drone Camera, Camera |
