Altec Lansing NanoPods Truly Wireless Earbuds with Charging Case-Complete Features/Instruction Guide

Altec Lansing NanoPods Truly Wireless Earbuds Let You Move With Complete Freedom When You Go Wireless! Altec Lansing portable Bluetooth earphones let you listen to music as you choose when you’re on the go or running on the track. Our TWS Bluetooth earphones are designed to produce a crystal-clear sound that will improve your listening experience. Our NanoPods Bluetooth earbuds for workouts are ideal for all of your indoor and outdoor activities because of the cordless design. They provide crystal-clear audio and, following the initial pairing, hook up with your phone automatically for practical use. Inside our wireless Bluetooth headphones are strong dynamic drivers that produce deep bass coupled with the ideal highs and lows. Ergonomic Fit & Fashion Forward Design For All Day Wear Those are compatible with the majority of Bluetooth-capable smartphones and devices on IOS and Android.

We don’t compromise on either comfort or sound quality. Our ergonomic Bluetooth wireless earphones are created with a stable connection and comfortable retention in mind, making them ideal for any indoor or outdoor activity. More practical features include: – Easy-to-use touch controls for portability; – A small charging case for portability; – A selection of colors to match your style; – An IPX5 waterproof design so you don’t have to worry about getting wet; – Up to 4 hours of use on a single charge; and 16 hours of charge from the case.

What’s In the Box?

A Closer Look

Charging

Placetheearbudsmto the case to charge

Charging(indicator is red)

Fully charged(lnd1cator is off)

The LED indicator flesh when charging

Connect the USB-C cable to the charging port to charge the case. The case’s indicator will flash momentarily to indicate a low battery.

Power On

For the first use, place the earbuds back into the case and then take them out of the case; this will activate the earbuds. To turn them on, place the earbuds into the case then take the earbuds out of the case. To turn them off, place the earbuds into the case.

If the LEDs do not turn on when the earbuds are removed from the case, charge the case then try again. In the event that the earbuds do not pair together, perform the Manual Reset function.

Bluetooth Pairing

To connect the earbuds to your smartphone, go to settings then select the Bluetooth page. Look under ‘available devices’ and connect to “NanoPods”.

Note
The earbuds will go into pairing mode automatically when taken out of the case.

Touch Button Function

Left Earbud Right Earbud

Decrease Volume: Press Once Increase Volume: Press Once
Previous Selection: Press Twice Next Selection: Press Twice

voice Assistant: Press & Hold 2 Sec. Pause/ Play: Press & Hold 2 Sec.
Answer Call: Press Once Answer Call: Press Once

Decline Call: Press Twice Decline Call: Press Twice
Hang Up Call: Press & Hold 2 Sec. Hang Up Call: Press & Hold 2 Sec.

Manual Reset

Only do this function experience issues that are not solved by simply turning the earbuds on/off, or by placing them back into the case.

Remove both earbuds from the case.
Hold down the left and right sensors for 9 seconds. Both earbuds will flash blue three times, then flash red and blue before resetting.
Place both earbuds back into the case to activate the earbuds and take both earbuds out of the case to re-pair the earbuds.
Reconnect the smartphone to your earbuds and continue to use it.

Notes

To use Siri or Google Assistant, you must have a phone that is compatible with one of those two voice assistants (iOS or Android, respectively). ou must be within Bluetooth range to use Siri or Google Assistant via your Wireless Earbuds.
Your Wireless Earbuds will not work with Siri or Google Assistant if the assistant is not first enabled within the settings on the phone. For more information, see your phone’s user manual.

For additional user materials and warranty information, please
visit alteclansing.com

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be detemined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for

Frequently Asked Questions

Is the case supposed to light up when it is plugged in?
Yes.
How do i connect these to my phone?
Bluetooth

Are these wireless charging compatible?
The case charges by USB C cord only
Does the case serve as an emergency power bank?
Yes
How to properly wear this? Does it keep popping out?
Use a smaller tip. I tried that, and how they’re absolutely perfect

Can you use one at a time?
It took me a while to get mine to both works at the same time. Here’s what works for me. If only one is working try reconnecting your Bluetooth a few times until they both are active.
Why might the case not come back on after it goes out and it’s fully charged?
It comes on when you put them back in after using them
Are these the nanobuds 2.0?
Hello sir, I think it is Nanopods version 1, not 2 because it is not written on it

Why won’t the light on my case light up while charging?
Mine doesn’t light up either. Charging is tricky as the earbuds don’t always charge either. (sensitive connectors)
Why do they not connect to each other even after a factory reset?
They do connect, just go to Bluetooth settings pair them and every time you take 1 out will connect, and the 2nd take it out and hit connect.

View Fullscreen

References

User Manual

Altec Lansing NanoPods Truly Wireless Earbuds with Charging Case

Specifications

Introduction