ALTA LABS ROUTE10 High Performance 10 Gbps Router User Guide

The Alta Labs logo LED on top of the device ﬂashes as the unit is powered up. Once fully booted, the LED will remain lit unless turned off in the UI. The LED color can also be changed in the management interface.

Bottom

The bottom of the device has padding for desktop placement and notches for mounting.

Front

Reset Button

Press down for 10 seconds until the LED begins ﬂashing to reset the router to factory defaults.

Ports 1-4 are standard Gigabit Ethernet ports that support 10/100/1000/2500 Mbps connections.

The Link LED on the left indicates a 10/100 Mbps connection when amber and blue indicates a 1 Gbps connection. For 2.5 Gbps connections, the LED on the right will illuminate white. If neither port LED is illuminated, then the connection is down.

Ports 2 and 3 support 802.3at PoE+ with up to 30W per port and a PoE budget of 40 Watts.

The PoE LEDs are located below ports 2 & 3 with the icon next to them. They will illuminate amber when a device connected to the port is being powered via Ethernet.

The SFP+ Ports support ﬁber optic and Ethernet transceivers with 1 Gbps, 2.5 Gbps, 5 Gbps, or 10 Gbps connections.

The Link LED on the left will illuminate blue when there is a 1 Gbps, 2.5 Gbps, or 5 Gbps connection, it will illuminate white with a 10 Gbps connection.

The Activity LED on the right ﬂashes blue when there is activity on a 1 Gbps, 2.5 Gbps, or 5 Gbps connection. It will ﬂash white if there is 10 Gbps network activity.

Back

Power Port Be sure to use the included power cord to connect power.

Hardware Installation

Mounting On A Wall

1. Locate the template included with the Quick Start Guide and Safety document.

2. Position the template in the desired location and use a pencil to mark the holes.

3. Secure the Mounting Bracket to the wall using the Mounting Screws and a Phillips screwdriver. Be sure to use the screws included with the product.

If mounting on drywall, use the anchors to ensure secure mounting. Use a 6 mm drill bit to drill the holes for the anchors and insert them in the wall.

4. Align the router with the Mounting Bracket.

Note: the Alta Labs A logo should be facing the same position on the mount and the router. Slide the notches over the tabs to lock Route10 into place.

5. Connect the Power Supply to the Route10 and the other end to a power outlet.

Connect a computer or switch to your Route10 using a CAT 5 (or above) Ethernet cable.

Set Up Your Device

Follow the instructions in the Alta app or management interface to set up your Route10.

Route10 Speciﬁcations

Mechanical
Dimensions						180 x 110 x 29.8 mm (7.09 x 4.33 x 1.17″)
Weight						0.46 kg (1.01 lbs)
Enclosure Material						Top cover: polycarbonate Bottom cover: milled aluminum
Material Finish						Matte
Color						White
Mount Material						Injection Molded Plastic

Ports
Network Interface						Ethernet, Bluetooth
Management Interface						(4) Autosensing 2500/1000/100/10 Mbps RJ45 Ports, (2) 10 Gbps/1.25 Gbps SFP+ Ports

LEDs
PoE						Amber
RJ45						Amber (Left LED): 10/100 Mbps Blue (Left LED): 1 Gbps White (Right LED): 2.5 Gbps
SFP+						Blue: < 10 Gbps White: 10 Gbps
Status						RGB/Multi-Color

Hardware
Processor						Quad-core Qualcomm 2.2 GHz
Button						Reset/Factory Reset
Network Interface						Ethernet, Bluetooth

Power
Power Supply						Universal AC, 100 – 240VAC 50-60Hz External
Maximum Power Consumption						70W
POE Budget						40W
Per-Port PoE						(2) 802.3at POE+, PoE+ (54VDC, 0.6A Max)
PoE Ports						2
Power
Bluetooth Version						BLE
Total Bluetooth Power						5 dBm EIRP
Bluetooth Gain						3 dBi
MAC Table Size						4k

Environmental
Mounting						Locking Wallmount, Desktop
Operating Temperature						-5 to 50° C (23 to 122° F) With (1) 2W SFP+ Module: 45° C (113° F) With (2) 2W SFP+ Modules: 40° C (104° F)
Operating Humidity						5 to 95% Noncondensing
Certiﬁcations						CE, FCC, IC
RJ45 Port Surge Protection						12kV for ESD – Contact, 25kV for ESD – Air

Software
VLAN						802.1Q
Easily Scale from Home to SMB to Stadium						Yes
Seamless Per- Client Settings						Yes
VPN Server						Yes, Multiple, Hardware-Accelerated
Actual Total Throughput						25 Gbps Combined Upload/Download
RADIUS Authentication						Yes
Deep-Packet Inspection						Yes
Intrustion Detection and Prevention Systems						Yes, at 10 Gbps
WAN Failover and Load-Balancing						Yes

Specifications

Model: Route10
DC Input / DC: 5V 1.827A
Manufacturer: Soundvision Technologies, dba Alta Labs
SN: ROUTE10ASXXWWXXXXXXXXXXXX

FCC ID: 2A8MT-ROUTE10
IC: 29180-ROUTE10

Compliance

Federal Communication Commission

Interference Statement

This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

This device is restricted to indoor use.

Non-Modiﬁcation Statement

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

CAN ICES-003(B) / NMB-003(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

ISED Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Community Forum forum.alta.inc

Technical Support help.alta.inc
All specifications are subject to change without notice.

Alta Labs products are sold with a limited warranty:
alta.inc/warranty

FAQ

Q: How do I change the LED color on top of the device?

A: The LED color can be changed in the management interface of the device.

Q: What do I do if I forget my Alta account login information?

A: You can initiate a password reset on the Alta Networks app or website to regain access to your account.

Q: Can I connect devices with different connection speeds to the SFP+ Ports?

A: Yes, the SFP+ Ports support various connection speeds including 1 Gbps, 2.5 Gbps, 5 Gbps, and 10 Gbps.

Documents / Resources

ALTA LABS ROUTE10 High Performance 10 Gbps Router [pdf] User Guide
ROUTE10, ROUTE10 High Performance 10 Gbps Router, High Performance 10 Gbps Router, 10 Gbps Router, Router

References

User Manual

ALTA LABS ROUTE10 High Performance 10 Gbps Router

Before You Begin

Package Contents

Installation Requirements

Hardware Overview

Top