TPMS10 Tire Pressure and Temperature Monitoring System
“
Specifications
- Product: Tire Pressure & Temperature Monitoring System
- Designed for: RVs, Motor-homes, Commercial Vehicles, and
Trailers
Product Information
The Tire Pressure & Temperature Monitoring System is
specially designed for RVs, motor-homes, commercial vehicles, and
trailers. It allows users to monitor tire pressure and temperature
to ensure safe and efficient travel.
Product Usage Instructions
Monitor Installation
Follow the instructions provided in the manual for installing
the monitor in your vehicle. Ensure it is securely mounted and
easily visible to the driver.
Sensor Installation
Refer to the manual for detailed sensor installation
instructions. Proper sensor installation is crucial for accurate
monitoring of tire pressure and temperature.
Deleting Sensor ID
If you need to delete a sensor ID from the system, follow the
steps outlined in the manual to ensure proper functioning of the
monitoring system.
Other Functions
Explore additional functions such as backlight and motion sensor
settings, out-of-parameter alerts, and sensor battery replacements
as needed.
Repeater/Signal Booster
If you experience signal loss due to distance or interference,
consider using a repeater/signal booster. Follow the provided
instructions for installation and usage.
FAQ
Q: How can I change the pressure units displayed on the
monitor?
A: You can switch between displaying tire pressure in PSI or BAR
by accessing the settings on the monitor. Refer to the manual for
detailed instructions on changing units.
Q: Can I set different pressure alerts for each axle?
A: Yes, you can customize pressure alerts for each axle to
accommodate additional towed trailers or vehicles. Follow the
instructions in the manual for setting axle-specific alerts.
Q: Where can I purchase an optional booster for signal
loss?
A: Optional boosters can be purchased from your dealer or local
distributor. Contact them for more information on acquiring a
booster for improved signal strength.
“`
TIREPRESSURE& TEMPERATUREMONITORINGSYSTEM
SpeciallyDesignedforRVs, Motor-homes,CommercialVehiclesandTrailers.
ThankyouforChoosingourTPMS, Ifyouencounteranysituationduringinstallationandusage, Wecouldbereachedat:support@finnet-tech.com Orifyouwillneedaphonecallservice, Justneedtoleaveamessagetoourserviceemailorourshopchatwindow, Ourservicestaffwillreachyouverysoon.
VideoLinkforSensor Programming(fromYoutube):
VideoLinkforSystem Settings(fromYoutube):
VideoLinkforTPMSCap SensorInstallation(fromyoutube):
VideoLinkforSensorbattery replacement(fromYoutube):
TABLEOFCONTENTS
SYSTEMCOMPONENTS …………………………………………………………………..1 SYSTEMOVERVIEW …………………………………………………………………………2 GENERALINFORMATION …………………………………………………………………..2 PRODUCTSFEATURES …………………………………………………………………….4 STARTYOURNEWSYSTEMSETTINGS(ALERTPARAMETERS) …………………4 PROGRAMMINGSENSORSTOTHEMONITOR ……………………………………….7
Method1-TabletopProgramming ………………………………………………7
Method2-AirInflationActivation ………………………………………………9
MONITORINSTALLATION …………………………………………………………………11
SENSORINSTALATION
…………………………………………………………………11
DELETINGSENSORID ……………………………………………………………………12
OTHERFUNCTIONS ……………………………………………………………………..12
BACKLIGHTANDMOTIONSENSOR …………………………………………………..12
OUTOFPARAMETERALERTS ………………………………………………………….13
REPLACINGANTI-THEFTSENSORBATTERY ……………………………………..16
FLOWTHROUGHSENSORBATTERYREPLACEMENT …………………………….17
REPEATER/SIGNALBOOSTER(OPTIONALPART) ………………………………..18
RecreationalVehicles,Towvehicles&Trailers ………………………………….18
PlacementInstruction ……………………………………………………………18
InstallationInstruction ……………………………………………………………18
REPEATER/BOOSTERALERTS …………………………………………………………19 High/LowPressure&FastLeakageAlerts …………………………………..19 HighTemperatureAlert ……………………………………………………………19
SPECIFICATIONS …………………………………………………………………………19 MONITOR …………………………………………………………………………………..20 SENSORS-Anti-theft …………………………………………………………………….20 SENSORS-FlowThrough …………………………………………………………………21
CAUTIONS ………………………………………………………………………………….22
SYSTEMCOMPONENTS
SETButton
SET
CODE
PowerButton&ParameterIncrease
CODEButton ParameterDecreaseButton
SuctionCupType-CChargingCableRepeater/Booster(Optionalpart)
SpareWaterproofO-ring
1
SYSTEMOVERVIEW
T h e s y ste m co m e s w i t h a m o n i to r t h at ca n h a n d l e 1 0 w h e e l s w i t h p re s s u re u p to210PSI.Thesensorsarelightweightedanddonotaffectthetirebalanceand haveeasytochangereplaceableCR1632batteries. Themonitordisplaysalltires’pressureortemperatureinafullscreen.Alarms canbepresetbytheoperatorsovisibleandaudiblealarmscanwarnthedriver ofacatastrophicfailure(rapidairpressureloss),highorlowpressuresandhigh temperature. The alarm and monitoring are sent wireless in real time to that cab allowing the operator to monitor tires that are out of their vision. The audiblealarmeliminatestheneedstowatchthemonitorcontinually.
TirePressurecanbedisplayedinPSIorBARandtemperatureinFahrenheit() orCelsius().Pressurealertscanbesettoadifferentpressuresettingforeach axle, so additional towed trailers or vehicles are no problem. An optional booster can be purchased from your dealer or your local distributor if you havesignallossduetodistance,structuralorelectronicinterference.
Tire monitor has a rechargeable lithium Ion batter y, Sensors come with either theAnti-theftsecurityfeatureorFlow-throughfeature.Themonitorcomeswith aType-Cchargingcable.
GENERALINFORMATION
A tire professional or your vehicle owner’s manual should be used to determinedthepropertirepressureforyourvehicle.Recommendedoperating tirepressuresshouldbesetwhentheambienttemperatureisloworcold.
Dramaticchangesintirepressurecanoccurbecauseof;increasedordecreased a m b i e n t te m p e rat u re , t i re co n ta ct s u r fa ce te m p e rat u re , w h e e l a n d a x l e l oa d s , sun shining on a side, etc. These and other conditions should be taken into considerationwhensettinginitialtireoperatingpressures.
2
This system cannot warn you of side wall failures; however, it can supply you withirregularpressuresandtemperatureinformationthatmayhelptoprevent this. If the monitor is shut off overnight simply switch the monitor back on before departure and your real time tire pressures and temperatures will be updated typically appear on the screen within 5 to 10 minutes. Even if the monitor is in the sleep mode the system is always monitoring and will alarm should any pressure settings or temperatures be out of your set parameters.
TheSchraderValve(coreinsidethevalvestem)shouldbethecorrectsize,bein goodconditionandbeabletobedepressedfullytoallowthereleaseofairto thesensorsoitcanoperate.Somevalvestemextensionsmaycauseinaccurate readingsiftheydonnotenablethesensortoworkcorrectly,metalbodied stems,orT-Valvetypeisrecommendedforbestperformance.Shouldyouhave difficultywithapressuresensornotworkingproperly,werecommendthatyou contactaprofessionaltoensurethetirestemandSchraderValveareinstalled andoperatingproperly.Ifusinginternaltiresealantsorbalancingcompounds/ beads,checkwiththemanufacturertoensuretheyarecompatiblewithTPMS systemsorthatyouhavefilteredvalvecoresinstalled.Overaperiod,tiresmay losepressurenaturally,throughthetireitselforforotherreasonssuchasrim leakage,etc.
Afterinstallingthesensorsonatirevalvestem,itisrecommendedtoperforma soapywatertestusing1/4dishsoapand3/4water.Spraythesoapysolutionon thevalvestemandsensorareatoensurethesensorisseatedalltheway.Ifair bubblesareseeninanyoftheseareas,thetiremaydeflate.Thewheelsensors areweatherproofandcanberunintherain. Consultatireprofessionalifanyoftheseareasprovetobeaproblem. Purchasersofthisproductshouldnotsolelyrelyonthistirepressure monitoring system for safety and should check the condition and pressure of theirvehicle’stiresonaregularbasisasdescribedbythemanufacturerofthe vehicle or tire manufacturer. Please note, this TPMS system works on an RF system, as with many RF tire systems this system can occasionally suffer from interference depending on the location of the system; thus, causing the system to be in accurate or not operate at all. Tire pressures and temperatures are not the only things that can affect tire safety; we suggest d a i l y v i s u a l i n s p e c t i o n s a n d p e r i o d i c c h e c k s b y t i r e p r o f e s s i o n a l s .
3
PRODUCTSFEATURES
MonitorFeatures
*Reliableandeasytoinstall. *4.3inchformonitordisplayarea. *B u i l t- i nre c h a rgea b l el i t h i u mi o nbatte r y. *Automaticlightsensorandbacklight. *Built-inmotionsensor. *Configurablehigh/lowpressurewarnings. *Configurablehigh/lowtemperaturewarnings. *Visibleandaudiblealerts. *Select-ablepressureunitfromPSIorBAR. *Select-abletemperatureunitfromor. *Displays10tires’pressureandtemperaturesimultaneously. *Longrangebetweenmonitorandsensors.
SensorFeatures
*Reliablecapsensors,easytoinstall. *Waterresistance. *Replaceablesensorbatteries. *Fastleakagealert. *Individuallycodedsensors.
Repeater/BoosterFeatures(OptionalPart)
*Maintainssignalstability.
STARTYOURNEWSYSTEMSETTINGS(ALERTPARAMETERS)
1.U npackallthecomponentsofyourTPMSsystemandensureitiscomplete. 2.T akethenumberkitfromtheaccessorypackandnumberallyoursensorsas indicatedbelow.(Tips:Afterputthestickerstothesensors,takesomeclearnail polishandpaintoverthenumber.Itwillkeepthestickeronthesensorsfor muchlongertimeinwetweatherconditions.) 3.P rogramthealarmparametersusingSTEP1settingyoursystemalarm parameters. 4.P rogrameachsensortothemonitorusingMETHOD1tabletoppage7 programmingsensorstothemonitor.
4
2
6 10
59
48
1
37
STEP1:SETTINGYOURSYSTEMSALARMPARAMETERS
TakeamemonoteofyourHigh/LowPressureSettingforeachaxleonthelast pageofyourmanualforfutureusage. 1.N exttoeachaxlewritedownwhatyourtirepressureisbyaxleandcalculate whatyouralarmsettingswillbe. 2.H ighPressureSettingwillbe(20%aboveyouraxlestandardtirepressure). 3.L owPressureSettingwillbe(10%belowyouraxlestandardtirepressure). Example:Frontaxlestandardtirepressureis100PSI HighPressureAlarmSettingwillbe120PSI(100PSIx1.2or120%)=120PSI. LowPressureAlarmSettingwillbe90PSI(100PSIx0.9or90%)=90PSI.
Flashes
5
STEP2:ChoosingPressureandTemperatureUnitofMeasure:
PRESS and HOLD the SET button, don’t release until you hear a beep. You will seePSIflashingonthescreen.YoucanchangetoBARbypressingthe+or-key. Whentheoneyouwanttouseappearsonthescreen,shortlypressSETbutton toselectyourtemperatureunit.Youwillseeorflashing.Shortlypress+or- keytoselecttheoneyouneed.
Flashes
ThenexttimethatyoupresstheSETbutton,thefrontaxelwillbeflashingand thewords” HIGHPRESSURE”willbedisplayed.Followtheinstructionsbelow.
Flash
6
STEP3:ChoosingperAxleHighandLowParameters:
Usingthesetkeyscrolltoyourfirstaxle”High”pressure.Usetheplusorminus
to set your HIGH PRESSURE. When you reach your desired pressure display,
shortly press and release the SET button again and” LOW PRESSURE” will be
displayed. Use the plus or minus key to set your low pressure. Press the SET
button again and the next axle will flash”HIGH PRESSURE”. Make you’re
a d j u st m e n ts t h e s a m e wa y a s fo r t h e fi r st a xe l . S k i p a n y a x l e s t h at y o u a re n ot
usingandjustkeephittingtheSETbuttonuntilyougototheaxlethatyouwant
to see. When you have finished setting your parameters PRESS and HOLD the
SETbuttonuntilthemonitorbeepsandyouarebacktodisplaymode.Keepin
mindthatthemonitorwilltimeoutin40minutes.So,writedownyoursettings
beforeyoustart.
Flash
PROGRAMMINGSENSORSTOTHEMONITOR
Method1-TabletopProgramming(thisistheeasiestway)
1.P RESSandHOLDbuttontoturnonthemonitor.Placethemonitorflaton thetableinfrontofyou.Thenplaceyournumberedsensorsonthetableabout afootawayfromthemonitor. 2.P ressandholdtheCODEbuttononthelowerrightsidedownuntilyouhear themonitorbeepsandallthe10tiresshowupwithnumber1tireblinking.After programming, only those tires that you program will show on the monitor. Placethemonitorflatonthetableandandthenplaceyournumber1sensoron thetablemakesurethatthesensoristouchingthebaseofthemonitornextto the” HoldSensorHere”sticker.Shortlypress+or-toselectthetireiconyou will need to program. When the blinking comes to the tire you select, shortly press CODE button and release, you will see an” LF” displays by the current programmingtire.Slightlyturnthesensoraroundclosetothemonitorbottom part,youwillhearabeep,andthecurrentsensorpressurereading(Usuallyit’s 00 under atmosphere pressure, it will be in normal readings after installed on tirevalve).Thatmeansyourfirsttireisprogrammed.
7
Then put your first sensor away and take the next sensor to your monitor. Shortly press button + or – to select the tire location for the second sensor. ShortlypressbuttonCODEandrelease,youwillsee” LF”byyoursecondtire. Slightlyturnthesensoraroundclosetothemonitorbottompart,youwillhear a beep, your second sensor is programmed. Repeat above steps for your rest sensors.
SET
CODE
3.W hen you have programmed the last sensor, press the CODE button down until the monitor sets off the alarm. Then turn off the monitor then turn it on again to make sure the tires are programmed in the right position. 4.I nstall your sensors to the valve stems in the order that you programmed them. Give the monitor 5 to 10 minutes depending on the number of sensorsthatyouhave.Oncethesensorsaresyncedyouwillnothavetore-sync unless you turn off the monitor. You will not lose any data if you turn off the m o n i to r. B u t yo u w i l l h a ve to wa i t fo r t h e s y ste m to re – s y n c w h e n yo u t u r n o ff the monitor back on. You can leave the monitor turned on by the monitor’s batte r y p o w e r. T h e n m o n i to r i n te r n a l batte r y w i l l r u n fo r a b o u t 6 0 h o u r s o r 3 0 daysbetweencharges.
NOTE: Ifyoufailedtheprogramming,themonitorwillissuetwoshortbeeps,slightly turnthesensoraroundnexttothemonitorbottom,shortlypressCODEbutton tot r yL Fm o d ea ga i n .I fy o ust i l lgett w ob e e p sp l ea s ec h e c kt h ebatte r yv o l ta ge w i t hav o l t m ete r.T h ev o l ta gei naf re s hbatte r ys h o u l db e3 . 2 V.I fi t’sato rb e l o w 2.8V, please replace with a fresh one. Make sure the battery is installed in the properorientationasshowninthismanual.
8
Method2-AirInflationActivation
1.P RESSandHOLDbuttontoturnonthemonitor. 2.P lacethesensorsonthetiresasnumberedonyourdiagrambutnotunderair pressureyet. 3.P ressandholdCODEbuttonuntilyouhearthemonitorbeep.Atthistime,you willseeall10tiresonthemonitorscreenandyournumberonetireiconshould beflashing.Usethe+or-buttontomovetothetireyouwanttoprogram.Place themonitorwithin3inchesofthesensorsandscrewthesensorallthewayon. Wa i t a fe w s e co n d s a n d t h e m o n i to r w i l l b e e p a n d t h e c u r re n t p re s s u re w i l l b e displayed. If it does not, take off the sensor from tire valve and wait for 10 seconds to screw it onto the tire valve again to try tire inflation. Once coded presstheplusbuttontogotothenexttireandrepeatthesteps.Usethepluskey togotothenexttireandrepeat.Skipanytirethatisnotonyourrig.
YOURSYSTEMISNOWSET-UPANDREADYFORUSE
MONITORDISPLAYINOPERATINGMODE:
After the sensors have all been programmed and the system is in operating mode, The monitor will display all tires’ pressure or temperature in a full screen.Thetirebeingtransmittedwillflashonthescreen,andthepressureand temperatureforthatwheelwillbedisplayedonthemonitor.Whenthemonitor is initially turned on, it may take up to 5 to 10 minutes for the monitor and sensors to sync up before the pressure and temperature will show on the monitor. Wait for all the tires to read before driving. After this time if you see onesensoristillnottransmittingthepressureandtemperature,youmaywant to reprogram the sensor. On an initial set up, it the tire still fails to indicate a pressure and temperature remove the sensor and back the Schrader Valve (valvecore)outapproximately1/8to1/4turnandre-installthesensor.Thiswill ensurethereisenoughcontactandairpressuretothesensor.
9
NOTESandRECOMMENDATIONS:
There will be an audible single” chirp” and the tire will flash if the monitor has not received a reading from that tire after 30 minutes. If you are stillreceivingPSIandtemperaturereadingsfromthesensors,thenthechirpis an indication of low battery on that sensor. The monitor solar panel works as thelightsensor.Whenyouseethesolarpowerchargingiconisshownon thetoprightsideofthescreen,itmeansthereisenoughlightforsolarpanelto turnonthecharging,thebacklightwillbeturnedofftosavingbatter ypower.If there is dark enough the backlight will automatically turn on if you could not see the solar power icon on the screen. The monitor comes with a built-in motionsensor;itwillgotosleep(energysavermode)ifthereisnomovementof the vehicle detected for approximately that the monitor is shut off when the systemisnotinuse,oryouarestayinginthevehicleovernight.Whenexternal powerisappliedtothemonitoritwilloverridethemanualon/offswitchonthe leftside.Youwillgetalongerservicelifefromyourmonitor’sinternalbattery,if you disconnect the external power source and allow the battery to deplete throughnormaloperationsever ycoupleweek’snaturally. This monitor only includes the acceptance function.
FactoryDefaults
Thefactor ydefaultsettingsareasfollows: HighPressure175PSI(12.1BAR), LowPressure35PSI(2.4BAR), Temperature158degrees(70).
RESTOREPARAMETERStoFACTORYDEFAULTS:
Turnoffthemonitor ;presstheSETbuttonandactivatethemonitoratthesame time, the factory settings will be restored. To delete a sensor ID see page 12.
10
MONITORINSTALLATION
Yoursystemcomeswithtwomountingoptions:aplastictowerwithsuctioncup mountforwindowordash,somepeopleprefertouseVelcroorthesmallbean bagsusedforcellphonesontheirdash.Mountitontothewindowscreenorleft side window using the suction cup provided ensuring you do not obstruct the d r i v e r ‘s v i s i o n o f t h e roa d . P l u g t h e p o w e r a d a pto r i n to t h e c i ga rette l i g h te r o r a u x i l i a r y p o w e r o u t l et a n d co n n e ct t h e p o w e r ca b l e to t h e m o n i to r. E n s u re t h e pinisalignedstraightwheninsertingitintotherightsideofthemonitor.When hardwiringitisrecommendingusinga” keyed”powersource.
CODE
SET
SENSORINSTALATION
1.Takeoutthelocknutoutfromaccessoriespackandscrewitontotirevalve. 2.Installthesensorontotirevalveandtightenitbyhand. 3.Usethewrenchprovidedtoscrewthelocknutontothesensoranticlockwise.
NOTE:Pleaseswitchonyourdisplaybeforesensorinstallation.
Installthesensor ontotirevalve
Tightenthesensor ontotirevalve clockwise
11
Tightenthelocknut ontothesensor anticlockwise
DELETINGSENSORID
1.I noperatingmode,pressandholdCODEbuttonuntilthemonitorbeepsand all 22 tires are showing. Press the + or – button to select the desired tire. 2.Press and hold the SET button for 3 seconds. A double beep sound will be issued, and you will see two dashes”- -” after the sensor code is deleted successfully. Use the + or – key to go to the next tire that you want to delete. To return to operating mode, press and hold CODE button until you hear the monitorbeep.
Flashes
OTHERFUNCTIONS
The monitor displays all your tires pressure or temperature in a full screen. Normallyitdisplayspressurereadingsconstantly.Butifyouwanttocheckthe temperature readings occasionally, just need to shortly press + or – key, the temperature reading will show for about 6 seconds then return to pressure readingautomatically.
BacklightandMotionSensor
Themonitorhasabuilt-inlightandmotionsensor.Thebacklightwillturntobe abitstrongerifthesolarpanelhasdetectedenoughlightintheenvironment. Thesolariconwillbeoninstrongbacklightmode.Thebacklightwill turntobenotsostrongiftheenvironmentisdark.Thesolariconwillbe o ff i n t h e d a r k ba c k l i g h t m o d e . T h e m o n i to r w i l l e n te r s l e e p m o d e to co n s e r v e batte r y l i fe i f t h e m ot i o n s e n s o r d o e s n ot d ete ct m ot i o n fo r 2 m i n u te s . I t w i l l come back to operating mode when it detects the vehicle is moving again or othermotion.
12
ChargingtheMonitor
T h el i t h i u m-i o nbatte r yi n s i d et h em o n i to r,w h e nf u l l yc h a rge dca nr u nfo r u pto6 0h o u r sb et w e e nc h a rge s .W h e nt h ebatte r ys y m b o lba r sa rego n e ,a rechargeisrequired.
OUTOFPARAMETERALERTS
Ifthereisameaningfulchangeinpressureortemperatureinthiscycleitwill transmittothemonitor.Ifnot,itwillmaintainthereadingandtransmitafull u p d atee v e r y5m i n u te s .T h i si stoco n s e r v et h es e n s o rbatte r y.I fa n yrea d i n g goesoutofthereal-timealert;youwillnoticethreethings: 1.A naudiblealarm. 2.T hecorrespondingtireonthemonitorwillflash,andatextmessageofwhatis wrongwillappearonthescreen. 3.P ressanybuttononthedisplayandthealarmwillstop.However,theflashing textmessagewillnotbeturnedoffuntilthecorrectpressureandtemperature settingsarerestoredtowithinrange.
13
MONITORALERTS
HighPressureAlert
W h e n t h e s e n s o r d e t e c t s h i g h pressureinatire,itwillsendanalert to the monitor immediately. High Pressure will show on the screen. Thecorrespondingtireiconwillflash. Theaudiblealarmwillbeontogether with the flashing alarm icon. Press any button to turn off the alarm. However the flashing tire icon and text will continue until the problem iscorrected.
LowPressureAlert
W h e n t h e s e n s o r d e t e c t s l o w pressureinatire,itwillsendanalert to the monitor immediately. Low Pressure will show on the screen. Thecorrespondingtireiconwillflash. Theaudiblealarmwillbeontogether with the flashing alarm icon. Press any button to turn off the alarm. However the flashing tire icon and text will continue until the problem iscorrected.
HighTemperatureAlert W h e n t h e s e n s o r d e t e c t s h i g h temperature in a tire, it will send an alert to the monitor immediately. High Temperature will show on the screen. The corresponding tire icon will flash. The audible alarm will be on together with the flashing alarm icon. Press any button to turn off the alarm.Howevertheflashingtireicon a n d t e xt w i l l co n t i n u e u n t i l t h e problemiscorrected.
14
FastleakageAlert When the sensor detects a rapid air loss in a tire, it will send an alert to t h e m o n i t o r i m m e d i a t e l y . F a s t Leakagewillshowonthescreen.The correspondingtireiconwillflash.The audible alarm will be on together with the flashing alarm icon. Press any button to turn off the alarm. However the flashing tire icon and text will continue until the problem iscorrected. SensorLowBatteryAlert When the sensor battery becomes l o w, i t w i l l s e n d a n a l e r t to t h e m o n i t o r i m m e d i a t e l y . S e n s o r Battery Low will show on the screen. Thecorrespondingtireiconwillflash. Theaudiblealarmwillbeontogether with the flashing alarm icon. Press any button to turn off the alarm. However the flashing tire icon and text will continue until the problem iscorrected.
ReplacingAnti-TheftSensorBattery
W h e ny o uh a v et h el o wbatte r ya l a r ms o u n dco m i n gf ro mt h em o n i to r,i ti st i m e tore p l a cet h ebatte r y. Re p l a cew i t haC R 1 6 3 2batte r y,w h i c ho p e rate sat- 2 0to 80. These can be purchased at many hardware stores, Radio Shack or large Walmart online at either eBay, Amazon or purchase from your local TPMS dealer.
15
1.Usethewrenchprovidedtoputonthesensorvalveasbelow.Thenscrewoff t h es e n s o rva l v ea n t i c l o c k w i s ea n do p e nt h ebatte r yca p.
2 .Ta keo u tt h ebatte r yf ro mbatte r yp o o l .
3 . I n sta l lan e wC r 1 6 3 2batte r yi n s i d et h ebatte r yp o o l ,m a kes u rep o s i t i v ep o l e upside.
4 . P u tba c kt h ebatte r yca pa n dt i g h te nt h eca pw i t ht h ew re n c hc l o c k w i s e . N OT E :Re p l a cean e wwate r p ro o fO – r i n gf ro mt h ea cce s s o r ypa c ki fi t’sb ro ke n .
Whenyouopenthesensornotethethinblackwire,itisthesensorsantenna. D on otb rea ki t .B ro ke na n te n n aw i reca u s e db yre p l a c i n gbat te r y.
16
FlowThroughSensorBatteryReplacement
When you hear the low battery beep, the next time you park the vehicle watch the monitor. Every time the monitor comes to that sensor the monitor will beep. Install CR1632 battery operates at -20 to 80. These can be p u r c h a s e d at m a n y h a r d w a r e sto r e s , R a d i o S h a c k o r l a r ge Wa l m a r t online at either eBay, Amazon or purchase from your local TPMS dealer. Use the hex/Allen wrench provided to remove the anti-theft screw and take of the sensor. Then use a small Phillip screw driver to take the capmarked” EasyTire”off.Underthecapisthebattery.Removeitandreplaceit with a new CR1632 batter y. Depending on how long the batter y was lowyoumayhavetoreprogramthesensor.
17
REPEATER/SIGNALBOOSTER(OPTIONALPART)
Recreational Vehicles, Tow Vehicles, Trailers and Tractor Trailer The Repeater/ Booster is designed to amplify the signal from your TPMS system sensors. In situationswhere.length,structureorelectronicinterferencepreventsyourmonitor from receiving a signal, the Repeater/Booster amplifies the sensors transmitting distance. Some Diesel Pushers experience difficulties do to the number of electroniccomponents in the engine compartment.As well as where sensors are shielded by bodywork etc. causing sensorsignal strength to be reduced and where extremely cold temperatures mayreduce sensor battery power. The optional signal Repeater/Boostercanbeorderedseparatelyandisavailableatyourlocaldealeror distributor.Thehard-wiredboostershouldhave12VDCpowerwhenthevehicleis moving.
REPEATER / BOOSTER SINGNAL INDICATION
Repeater / booster singal indicator ( ) will be displayed on monitor screen when repeaterisconnectedwithpowersupply(12~24V)andreceivedsignalsfromsensors. Ifthereisnosignalsfromsensorsover15mins,thesignalindicatorwillbeoff.
Abooster/signalrepeater(shouldbeorderedseparatly)couldbeusedfor trailer exchange. It is required to install a booster for each trailer. For towing truckitisrecommendedtoinstalltheboosterattherearpartofthevehicle. Fortrailers,itisrecommenedtoinstalltheboosterinfrontofeachtrailer.
18
Hint:Mostpeopleinstallthemintotheiraftcompagtmentorclosetinthecoach andwireitintothecompartmentorclosetlight.Byplacingitonthecoachyou receive the advantage of the Repeater/Booster even when your tow vehicle is notconnected.INSTALLATIONINSTRUCTIONSBesuretowiretheRepeaterinto a12Vpowersourcethatwillbe”on”duringvehicleoperation.TheRepeaterwill beonassoonasitisconnectedtopower.Theredlightstaysonwhenpoweris connected.
High/LowPressureandFastLeakAlertsWhenthesensordetectshigh/lowpressureabnormalitiesandrapidleaks,itwillsendanalerttotheRepeater/ Boosterimmediately.Theaudiblealarmwillbeontogetherwiththeflashing redlight.Pressanybuttononthemonitortoturnoffthealarm.However,the flashingredlightwillcontinueuntiltheissueisresolved.Thesystemissetto alarmifyoulosemorethan7.25psiinaminute.
19
20
CAUTIONS
1.T hemonitorshouldbeinstalledinthevehiclewhereitdoesnotaffectnormal driving. 2.T hemonitorshouldbewellfixedtoavoidfallingoffduringdriving. 3.R egulartireinspectionandmaintenanceisstillnecessary. 4.A fterthesystemisinstalledcorrectly,thedriverdoesnotneedtostaratthe monitorallthetimewhiledriving.Alertswillbeissuedwhenabnormal conditionsarefoundinthetires. *Informationinthismanualissubjecttochangewithoutnotice.
DISCLARMEROFWARRANTY:
Thewarrantyappliestotheoriginalpurchaseronly.Thewarrantydoesnot carry over nor is it transferable to another party. Neither the seller nor the manufacturer will be liable for any loss damage party. Neither the indirectly arising from the use or inability the suitability of the product for its intended use, and the user shall assume all responsibility and risk in connection herewith.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
22
Documents / Resources
 |
Aiwei TPMS10 Tire Pressure and Temperature Monitoring System [pdf] User Manual 2BMRE-TPMS10, 2BMRETPMS10, TPMS10 Tire Pressure and Temperature Monitoring System, TPMS10, Tire Pressure and Temperature Monitoring System, Pressure and Temperature Monitoring System, Temperature Monitoring System, Monitoring System, System |