Solo 2/Solo 2 DL, EVO4S XLog and ECULog kit
“
Specifications:
- Compatible Models: Suzuki GSX-R 600 (2004-2023), GSX-R 750
(2004-2017), GSX-R1000 (2005-2023), GSX-R 1300 (2008-2016) - Release: 1.02
Product Usage Instructions:
1. Models and Years
This manual explains how to connect Solo 2 DL, EVO4S, XLog, and
ECULog to the bike engine control unit (ECU). Compatible models and
years are:
- 2004-2023
- 2004-2017
- 2005-2023
- 2008-2016
Warning: AiM recommends not to remove the stock
dash for the mentioned models/years to avoid disabling bike
functions or safety controls.
2. Kit Content and Part Numbers
- 2.1 Bracket for Solo 2/Solo 2 DL: Installation
bracket does not fit certain Suzuki models, please check
compatibility. - 2.2 AiM cable for Solo 2 DL, EVO4S, XLog, and
ECULog: Refer to the image for cable construction
scheme. - 2.3 Solo 2 DL kit (AiM cable + bracket):
Installation bracket and connection cable can be purchased together
with a specific part number.
3. Solo 2 DL, EVO4S, XLog and ECULog Connection
To connect the mentioned devices to the bike ECU, use the white
diagnostic connector located under the bike seat. Remove the black
rubber cap on the ECU diagnostic connector and connect the AiM
cable to the Suzuki connector.
4. Configuring with RaceStudio 3
Configure using SDS_protocol for most models except for Suzuki
GSX-R 1000 from 2017 which requires SDS 2 Protocol.
5. Suzuki Protocols
The channels received by AiM devices configured with Suzuki
protocols vary based on the selected protocol. Refer to the
provided list of functions and corresponding channels.
FAQ:
Q: Can I use this product with other motorcycle models not
listed in the manual?
A: It is recommended to use the product only with the compatible
models mentioned in the manual to ensure proper functionality and
avoid any issues.
“`
AiM User Guide
Solo 2/Solo 2 DL, EVO4S, XLog and ECULog kit for Suzuki GSX-R 600 (2004-2023) GSX-R 750 (2004-2017) GSX-R1000 (2005-2023) GSX-R 1300 (2008-2016) Release 1.02
1
1 Models and years
This manual explains how to connect Solo 2 DL, EVO4S, XLog and ECULog to the bike engine control unit (ECU).
Compatible models and years are:
· GSX-R 600 · GSX-R 750 · GSX-R 1000 · GSX-R 1300 Hayabusa Gen. 2
2004-2023 2004-2017 2005-2023 2008-2016
Warning: for these models/years AiM recommends not to remove the stock dash. Doing so will disable some of the bike functions or safety controls. AiM Tech Srl will not be held responsible for any consequence that may result from the replacement of the original instrumentation cluster.
1
2 Kit content and part numbers
AiM developed a specific installation bracket for Solo 2/Solo 2 DL that fits some bike models only specified in the following paragraph and a CAN connection cable to the ECU for Solo 2 DL, EVO4S, XLog and ECULog.
2.1 Bracket for Solo 2/Solo 2 DL
Part number of Solo 2/Solo 2 DL installation bracket for Suzuki GSX-R shown below is: X46KSSGSXR.
Installation kit contains: · 1 bracket (1) · 1 Allen screw with rounded head M8x45mm (2) · 2 Allen screws with flat head M4x10mm (3) · 1 toothed washer (4) · 1 rubber dowel (5)
Please note: installation bracket does not fit Suzuki GSX-R 1000 bikes from 2005 to 2008 nor Suzuki GSX-R 1300 Hayabusa Gen. 2 from 2008 to 2016 included.
2
2.2 AiM cable for Solo 2 DL, EVO4S, XLog and ECULog
Part number of connection cable for Suzuki GSX-R shown below is: V02569140.
Following image shows the cable constructive scheme.
2.3 Solo 2 DL kit (AiM cable + bracket)
Solo 2 DL installation bracket and connection cable for Suzuki GSX-R can also be bought together with part number: V0256914CS. Please remember that the bracket does not fit Suzuki GSX-R 1000 from 2005 to 2008 nor Suzuki GSX-R 1300 Hayabusa Gen. 2 from 2008 to 2016.
3
3 Solo 2 DL, EVO4S, XLog and ECULog connection
To connect Solo 2 DL, EVO4S and ECULog, XLog to the bike ECU use the white diagnostic connector placed under the bike seat and shown here below. Lifting the bike seat the ECU diagnostic connector shows a black rubber cap (shown bottom in the image here on the right): remove it and connect AiM cable to Suzuki connector.
4 Configuring with RaceStudio 3
Before connecting AiM device to the bike ECU set all functions using AiM RaceStudio 3 software. The parameters to set in the device configuration section (“ECU Stream” tab) are: · ECU Manufacturer: “Suzuki” · ECU Model: (RaceStudio 3 only)
o “SDS_protocol” for all models except for Suzuki GSX-R 1000 from 2017 o “SDS 2 Protocol” for Suzuki GSX-R 1000 from 2017
4
5 Suzuki protocols
Channels received by AiM devices configured with Suzuki protocols change according to the selected protocol.
5.1 “Suzuki SDS_Protocol”
Channels received by AiM devices configured with “Suzuki SDS_Protocol” protocol are:
CHANNEL NAME
FUNCTION
SDS RPM SDS TPS SDS GEAR SDS BATT VOLT SDS CLT SDS IAT SDS MAP SDS BAROM SDS BOOST SDS AFR SDS NEUT SDS CLUT SDS FUEL1 pw SDS FUEL2 pw SDS FUEL3 pw SDS FUEL4 pw SDS MS SDS XON ON
RPM Primary throttle position Engaged gear Battery supply Engine coolant temperature Intake air temperature Manifold air pressure Barometric pressure Boost pressure Air/Fuel ratio Neutral switch Clutch switch Fuel injector 1 Fuel injector 2 Fuel injector 3 Fuel injector 4 Mode selector XON switch
5
SDS PAIR SDS IGN ANG SDS STP
PAIR ventilation system Ignition angle Secondary throttle position
Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable.
6
5.2 “Suzuki SDS 2 Protocol”
Channels received by AiM devices configured with “Suzuki SDS 2 Protocol” protocol are:
CHANNEL NAME
FUNCTION
SDS RPM
RPM
SDS SPEED R
Rear wheel speed
SDS SPEED F
Front wheel speed
SDS GEAR
Engaged gear
SDS BATT VOLT
Battery voltage
SDS CLT
Engine coolant temperature
SDS IAT
Intake air temperature
SDS MAP
Manifold air pressure
SDS BAROM
Barometric pressure
SDS FUEL1 msx10
Fuel injector 1
SDS FUEL2 msx10
Fuel injector 2
SDS FUEL3 msx10
Fuel injector 3
SDS FUEL4 msx10
Fuel injector 4
SDS IGN AN 1 SDS IGN AN 2 SDS IGN AN 3 SDS IGN AN 4
Ignition Angle 1 Ignition Angle 2 Ignition Angle 3 Ignition Angle 4
SDS TPS1 V
TPS1 voltage
SDS TPS2 V
TPS2 voltage
SDS GRIP1 V
Grip1 voltage
SDS GRIP2 V
Grip2 voltage
SDS SHIFT SENS
Shift sensor
SDS TPS1
Primary throttle position
SDS TPS2
Secondary throttle position
SDS GRIP1
Grip1 position
7
SDS GRIP2 SDS SPIN RATE SDS SPIN RT TC SDS DH COR AN
Grip2 position Wheel spin rate (TC: off) Wheel spin rate (TC: on) Dashspot correction angle
Technical note: not all data channels outlined in the ECU template are validated for each manufacturer model or variant; some of the outlined channels are model and year specific, and therefore may not be applicable. The following channels work only if the system is connected to a Yoshimura ECU:
· SDS SPEED F · SDS SPIN RATE · SDS SPIN RT TCC · SDS DH COR AN
8
Documents / Resources
 |
AiM Solo 2/Solo 2 DL, EVO4S XLog and ECULog kit [pdf] User Guide Solo 2 Solo 2 DL EVO4S XLog and ECULog kit, Solo 2 Solo 2 DL EVO4S, XLog and ECULog kit, ECULog kit, kit |