SMARTRISE VERSION 1.03 C4 LINK2 PROGRAMMER

Spesifikasies

• Produk Naam: C4 Link2 Programmeerder
• Weergawe: 1.03
• Datum: 7 November 2025

verbyview

• Hierdie dokument verskaf stap-vir-stap instruksies vir die aflaai, installering en gebruik van die Link2-programmeerder met C4-beheerders. Dit verduidelik hoe om sagteware op die C4-beheerder te laai met behulp van die Link2-programmeerder.

Required Tools for Software Programming

Die volgende gereedskap word benodig om die sagteware te programmeer:

1. 'n Skootrekenaar met 'n Windows-gebaseerde bedryfstelsel.
2. Die Link2 Programmeerder.
3. Controller software: The original controller software is stored on a flash drive inside the white job binder. If the flash drive is missing or contains outdated prints and software, Smartrise can provide a webskakel om toegang tot die nuutste sagteware en afdrukke te verkry.

Application Download Instructions

Om sagteware op die Smartrise-beheerder te laai, moet die programmeringstoepassing na die skootrekenaar afgelaai word. Hierdie toepassing is beskikbaar op die USB-geheuestokkie. Volg hierdie stappe om die C4 Link2 Programmer-toepassing af te laai:

1. Maak die flash drive oop.
2. Navigate to (5) – Smartrise Programs and open the folder.
3. Vind en maak die C4 Programmer-lêergids oop.
4. Download and run both applications on the laptop. Some laptops may have firewalls that prevent applications from downloading. For assistance, contact the system administrator.
5. Once completed, the two applications should appear on the desktop.
   NOTE: MCUXpresso does not need to be opened, only installed on the laptop.

Software Loading Instructions

Om behoorlike funksionaliteit te verseker, moet die beheerdersagteware op die Smartrise-beheerder gelaai word met behulp van die Link2-programmeerder. Volg die stappe hieronder om die proses te voltooi:

1. Connect the Link2 Programmer to the laptop via the USB port.
2. Open the C4 Link2 Programmer by double-clicking its icon. The application will automatically update to the latest version if connected to the internet. Ensure the application is up to date before proceeding.
3. Blaai deur die beheerder sagteware:
   • Open (1) – Controller Software.
   • Kies die lêergids met die werknaam.
   • Kies die motor om sagteware voor te laai.
   • Klik Kies vouer onderaan die venster.
4. Select the processor to update using the dropdown menu. Processors can be updated in any order:
   • MNR. A: MNR. MCUA
   • MNR. B: MNR. MCUB
   • SRU A: CT en COP MCUA
   • SRU B: CT en COP MCUB
   • Stig/Uitbreiding: Stig/Uitbreidingsbord
   • Verwerkerverbindings kan op die bord gevind word.
5. Start the software loading process by clicking the Start button.
   • Belangrik: Wanneer die MR SRU geprogrammeer word, kan ander motors in die groep beïnvloed word. Om dit te voorkom, ontkoppel die groepterminale op die bord.
6. A new window will appear, and the software download will begin. Once complete, a confirmation message will be displayed.LET WEL: Indien die sagteware nie aflaai nie, probeer die volgende:
   • Retry the process.
   • Gebruik 'n ander USB-poort.
   • Power cycle the controller.
   • Ensure the Link2 Programmer is properly connected.
   • Herbegin die skootrekenaar.
   • Try a different Link2 Programmer.
   • Use a different laptop.
   • Contact Smartrise for assistance.
7. Click Edit to continue loading software for the remaining processors and follow the previous steps.
8. Once all software uploads are complete, reconnect the group terminals and power cycle the controller.
9. Verify the software version under Main Menu | About | Vers.
10. Rollees af na view alle opsies en bevestig dat die verwagte weergawe vertoon word.
    • WERKNAAM
    • SRU BOARD
    • CAR LABEL
    • JOB ID: ########
    • VERS. ##.##.##
    • © 2023 SMARTRISE
11. Default to factory settings by navigating to Main Menu | Setup | Miscellaneous | Default | Default Factory.

Restoring a Bricked Processor

In the event of a bricked processor, follow the steps below to restore functionality:

1. Locate the two jumpers positioned beneath the LCD display – one jumper corresponds to each processor.
2. Connect the jumper associated with the affected (bricked) processor to establish communication.
3. Power cycle the board.
4. Once power is restored, program the processor using a release file that already includes a bootloader.
5. Start the application once programming is complete.
6. Remove the jumper used for recovery.
7. Power cycle the board again to finalize the restoration.

Gereelde vrae

Q: What should I do if I encounter issues with downloading the programming application?

A: If you face problems downloading the programming application due to firewalls or other reasons, contact your system administrator for assistance.

Dokumente / Hulpbronne

SMARTRISE VERSION 1.03 C4 LINK2 PROGRAMMER [pdf] Gebruikersgids VERSION 1.03 C4 LINK2 PROGRAMMER, VERSION 1.03, C4 LINK2 PROGRAMMER, LINK2 PROGRAMMER, PROGRAMMER

Verwysings

• Gebruikershandleiding