YAXUN YX-884D+

Contents

YAXUN YX-884D+ 3-in-1 Rework Soldering Station User Manual

Model: YX-884D+

1. Introduction

Thank you for choosing the YAXUN YX-884D+ 3-in-1 Rework Soldering Station. This professional tool integrates a soldering iron, a hot air gun, and a DC power supply into a single compact unit, making it ideal for electronics repair, SMD rework, and various soldering tasks. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting to ensure optimal performance and longevity of your device.

2. Safety Precautions

  • Always operate the unit in a well-ventilated area to avoid inhaling fumes from soldering.
  • The soldering iron tip and hot air gun nozzle reach very high temperatures. Avoid direct contact with skin or flammable materials.
  • Use appropriate personal protective equipment (PPE) such as safety glasses and heat-resistant gloves.
  • Ensure the unit is properly grounded. Do not use if the power cord is damaged.
  • Never immerse the unit in water or use it in wet conditions.
  • Turn off the power and unplug the unit before cleaning or maintenance.
  • Keep out of reach of children.

3. Package Contents

Please check the package contents against the list below. If any items are missing or damaged, contact your vendor.

  • 1 x YAXUN YX-884D+ Main Unit
  • 1 x Soldering Iron
  • 1 x Soldering Iron Stand
  • 1 x Soldering Sponge
  • 1 x Hot Air Gun Handle
  • 3 x Hot Air Gun Nozzles (various sizes)
  • 1 x Tool for IC Chip Removal
  • 1 x Voltage Testing Cable (for DC power supply)
  • 1 x Power Cord
  • 1 x User Manual (this document)
All components included in the Yaxun YX-884D+ package, including the main unit, soldering iron, hot air gun, stand, sponge, nozzles, IC tool, and test leads.
Figure 3.1: Included Package Contents

4. Product Overview

4.1 Front Panel

Front panel of the Yaxun YX-884D+ showing controls for soldering temperature, hot air temperature and airflow, and DC power supply voltage and current displays.
Figure 4.1: Front Panel Layout
  • Soldering Iron Temperature Display (℃): Shows the set and actual temperature of the soldering iron.
  • Soldering Iron Temperature Knob: Adjusts the soldering iron temperature (200-480℃).
  • Soldering Iron Input: Connector for the soldering iron.
  • Hot Air Gun Temperature Display (℃): Shows the set and actual temperature of the hot air gun.
  • Hot Air Gun Air Flow Knob: Adjusts the air volume for the hot air gun.
  • Hot Air Gun Temperature Knob: Adjusts the hot air gun temperature (100-450℃).
  • Hot Air Gun Input: Connector for the hot air gun.
  • DC Power Supply Voltage Display (V): Shows the output voltage of the DC power supply.
  • DC Power Supply Current Display (A): Shows the output current of the DC power supply.
  • DC Power Supply Output Terminals: Red (+) and Black (-) terminals for power output.
  • DC Power Supply Test Input: Green (0V) and Yellow (15V) terminals for voltage testing.
  • Power Switches: Individual switches for Soldering, SMD Rework (Hot Air), and DC Power Supply.

4.2 Rear Panel

Rear panel of the Yaxun YX-884D+ showing the main power input socket and fuse holder.
Figure 4.2: Rear Panel Layout
  • AC Power Input Socket: Connects the main power cord.
  • Fuse Holder: Contains the main protective fuse.

5. Setup

  1. Placement: Place the main unit on a stable, heat-resistant, and non-flammable surface. Ensure adequate space around the unit for ventilation.
  2. Connect Soldering Iron: Plug the soldering iron connector into the 'SOLDERING' input port on the front panel. Place the soldering iron in its stand.
  3. Connect Hot Air Gun: Plug the hot air gun connector into the 'SMD REWORK' input port on the front panel. Place the hot air gun in its holder.
  4. Connect DC Power Supply Test Leads (Optional): If using the DC power supply for testing, connect the red and black test leads to the corresponding 'OUTPUT' terminals. For voltage testing, connect the provided voltage testing cable to the 'TEST INPUT' terminals.
  5. Power Connection: Ensure all individual power switches on the front panel are in the 'OFF' position. Connect the power cord to the AC power input socket on the rear panel, then plug the other end into a suitable grounded AC power outlet.

6. Operating Instructions

6.1 General Operation

  1. After setup, turn on the main power switch (usually located on the rear or side, if present, otherwise proceed to individual switches).
  2. Activate the desired function (Soldering, SMD Rework, or DC Power Supply) using its respective switch on the front panel.
  3. Adjust settings as described in the following sections.
  4. When finished, turn off the individual function switch, then unplug the unit from the main power outlet.

6.2 Soldering Iron Operation

  1. Turn on the 'SOLDERING' power switch. The display will show the current tip temperature.
  2. Rotate the 'SOLDERING' temperature knob to set the desired temperature (e.g., 350℃ for general leaded solder). The display will show the set temperature briefly, then return to the actual temperature as it heats up.
  3. Allow a few minutes for the iron to reach the set temperature.
  4. Before soldering, clean the tip on the damp sponge provided.
  5. Apply solder to the joint. After use, clean the tip and tin it with a small amount of solder to prevent oxidation.

6.3 Hot Air Gun Operation

  1. Turn on the 'SMD REWORK' power switch.
  2. Rotate the 'AIR' flow knob to set the desired air volume. Start with a lower setting and increase as needed.
  3. Rotate the 'SMD REWORK' temperature knob to set the desired temperature (e.g., 300-350℃ for typical SMD desoldering).
  4. Allow the hot air gun to reach the set temperature.
  5. Direct the hot air flow onto the component to be reworked. Maintain a safe distance to avoid damaging surrounding components.
  6. Auto-Sleep Function: When the hot air gun is placed back into its holder, it will automatically cool down and enter sleep mode, extending the heater's lifespan. It will resume operation when lifted from the holder.

6.4 DC Power Supply Operation

  1. Turn on the 'DC POWER SUPPLY' power switch. The voltage and current displays will illuminate.
  2. The output voltage is fixed at 15V. The current limit is 2A.
  3. Connect your device or circuit to the 'OUTPUT' terminals (Red for positive, Black for negative).
  4. The displays will show the voltage and current being drawn by the connected load.
  5. DC Voltage Testing Function: Use the provided voltage testing cable. Connect the red probe to the positive point of the component/battery you want to test, and the black probe to the negative point. Insert the banana plugs into the 'TEST INPUT' (Green for 0V, Yellow for 15V). The DC power supply's voltage display will show the measured voltage.
Video 6.1: Product demonstration showing soldering, hot air rework, auto-sleep function, and DC voltage testing.

7. Maintenance

  • Soldering Iron Tip Care: Always keep the soldering tip clean and tinned. Clean the tip frequently with the damp sponge. Replace tips when they become excessively worn or corroded.
  • Hot Air Gun Nozzle Care: Ensure nozzles are free from debris. Clean them gently if clogged. Replace if damaged.
  • General Cleaning: Periodically wipe the main unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the unit is unplugged and cool before cleaning.
  • Fuse Replacement: If the unit fails to power on, check the fuse in the fuse holder on the rear panel. Replace it with a fuse of the same type and rating.

8. Troubleshooting

ProblemPossible CauseSolution
Unit does not power onNo power from outlet; Power cord loose; Blown fuseCheck power outlet; Reconnect power cord; Replace fuse
Soldering iron not heatingIron not connected properly; Heating element failureCheck connection; Contact support
Hot air gun not heating or no airflowGun not connected properly; Heating element or fan failureCheck connection; Contact support
DC power supply no outputSwitch off; Internal faultEnsure switch is ON; Contact support

9. Specifications

Dimensions of the Yaxun YX-884D+ main unit: 25cm length, 17cm width, 15cm height.
Figure 9.1: Main Unit Dimensions
General Specifications
Rated VoltageAC: 220V ± 10% 50HZ or 110V ± 10% 60HZ
Total Power765W ± 10% (max)
Work Environment0-50 ℃
Storage Temperature-20-80 ℃
Dimensions (L x W x H)25cm x 17cm x 15cm
Weight5.0 kg
Soldering Iron Specifications
Output VoltageAC: 26V ± 10%
Output Power50W ± 10%
Temperature Range200 - 480 ℃
Temperature Stability± 2 ℃
Tip to Ground Resistance< 2 ohm
Tip to Ground Voltage< 2 mV
Hot Air Gun Specifications
Operating VoltageAC: 220V ± 10% 50HZ or 110V ± 10% 60HZ
Output Power700W ± 10%
Temperature Range100 - 450 ℃
Temperature Stability± 2 ℃
DC Power Supply Specifications
Operating VoltageAC: 220V ± 10% 50HZ or 110V ± 10% 60HZ
Output Power15W
Output Voltage0-15V (Fixed)
Output Current2A (Fixed)
Load Regulation< 0.01 ± 2mV
Ripple Noise< 1mVrms (RMS virtual value)
Temperature Coefficient< 300PPm / ℃
Protection Start Current> 10% of the nominal value

10. User Tips

While no specific user tips were available from reviews or Q&A, general best practices for soldering stations include:

  • Always use flux for cleaner and stronger solder joints.
  • Ensure your workspace is clean and free of clutter.
  • Practice on scrap PCBs before working on critical components.

11. Warranty and Support

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. Please refer to your purchase documentation for specific warranty terms and duration. For technical support, service, or warranty claims, please contact your original point of purchase or the authorized YAXUN distributor in your region. Keep your proof of purchase for warranty validation.

© 2023 YAXUN. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.