AnyTone AT-708plus

Contents

Anytone AT-708 Plus 27MHz CB Radio Instruction Manual

Model: AT-708plus

Introduction

This manual provides detailed instructions for the proper use, installation, and maintenance of your Anytone AT-708 Plus 27MHz CB Radio. Please read this manual thoroughly before operating the device to ensure optimal performance and safety.

Product Unboxing and Preparation

Package Contents

Upon opening the packaging, please verify that all the following items are included:

  • AT-708PLUS CB Radio (Interphone host) x1
  • Hand Microphone x1
  • Microphone Clip x1
  • Fix Bracket x1
  • Screw Set x1
  • User's Manual x1
Anytone AT-708PLUS CB Radio in its packaging with microphone
Anytone AT-708PLUS CB Radio and accessories in its packaging.
Diagram showing the package contents of the AT-708PLUS CB Radio
Visual representation of the package contents.

Installation Steps

  1. Antenna Installation: Align the antenna with the interface and rotate clockwise to tighten it. When twisting the antenna, hold the base of the antenna and rotate it. Do not shake the top of the antenna to avoid damaging the internal wiring.
  2. Battery Installation: Align the battery with the slot on the back of the body and push it down until you hear a "click" to lock it.

Basic Operation Guide

1. Charging Instructions

  • First Use: The new battery is usually in a low battery state. It is recommended to charge it for 4-6 hours when turned off for optimal performance.
  • Charging Method: Connect the charger to the power source. Insert the walkie talkie (without shutting down) into the charging dock/USB for charging. Ensure good contact between the body and the charging pole.
  • Indicator Light Status: The indicator light is red when charging and turns green when fully charged.
  • Kind Reminder: Please remove the battery promptly after it is fully charged, as overcharging can affect battery life.

2. Power On and Off

Press and hold the power button (usually integrated with the volume knob) for about 2-3 seconds. After turning on, the screen lights up and is accompanied by a prompt sound. To power off, rotate the ON/OFF VOL knob counter-clockwise until it clicks off.

3. Adjust the Volume

Rotate the volume knob (usually integrated with the power button):

  • Rotate clockwise to increase the volume.
  • Rotate counterclockwise to decrease the volume.

It is suggested to adjust the volume according to environmental noise; the appropriate level is better than the loudest.

4. How to Make a Call (PTT)

The walkie talkie adopts a "press and speak" half-duplex mode, where only one party can speak at a time.

  • Launch (Speech): Press and hold the PTT (Push To Talk) button on the side of the microphone. Hold the walkie talkie vertically, with the microphone about 2.5-5 centimeters away from your mouth. Speak clearly at a normal pace, then release the PTT button after speaking.
  • Reception (Listening): After releasing the PTT button, the walkie talkie automatically enters the receiving mode. At this moment, you will hear the other person's speech.
  • Telephone Etiquette: Pause slightly before speaking to avoid interrupting. After finishing the key information, usually add "Done" or "Over" to inform the other party that you have finished speaking and can release the button.

5. Advanced Features

  • One-Click Frequency Matching/Copying: Some walkie talkies support frequency duplication. Bring two walkie talkies closer together. For the transmitter, enter the menu and select "Copy" or "CLONE" mode. The receiver also enters replication mode. Press the PTT button on the transmitter, and the data will be automatically transmitted.
  • Scanning Function: When you are unsure which channel the other party is on, you can press the SCAN button. The walkie talkie will automatically cycle to detect the signal of the current channel and stop automatically when there is a signal.
  • Voice Control Function (VOX): After enabling the VOX function, you don't need to press the PTT button; you can directly speak into the walkie talkie to transmit. This is suitable for use when both hands are occupied.
Demonstration of basic operations including volume adjustment, channel change, band change, AM/FM mode selection, scan function, and PTT button usage.
Front view of the Anytone AT-708PLUS CB Radio with microphone connected
Front view of the radio with microphone connected, showing controls.
Side view of the Anytone AT-708PLUS CB Radio showing dimensions
Side view of the radio with approximate dimensions.

Maintenance

Daily Maintenance

  • Cleaning: If the body becomes dirty, wipe it with a soft cloth dampened with neutral detergent. Do not use alcohol, spray, or other harsh detergents, as they may corrode the shell.
  • Storage: When not in use for a long time, turn off the walkie talkie and remove the battery. Store it in a dry and cool place.

Troubleshooting

Refer to the table below for common issues and their solutions:

Problem PhenomenonPossible Causes and Solutions
Unable to power onThe battery is fully discharged (please charge); Poor battery contact (remove and reinstall).
Too close call distance/noiseLow battery level (please charge); Located in a dead corner of the building (change position); The antenna is not tightened.
The other party cannot hear my voiceDid not hold down the PTT key while speaking; The microphone is too far from the mouth.
The charging indicator light is not onThe charger is not plugged in properly; Poor contact between the body and the charging dock; The battery is damaged.

Specifications

GENERAL
Modulation ModeAM/FM
Frequency Range24.265-29.655MHz
Frequency Tolerance±5.0ppm
Input Voltage13.2V DC ±15%
Dimensions180 (L)x35 (H)x140 (P) mm (from product properties) / 140*195*37mm (from desc.html)
Weight656g
Operating Temperature Range-20°C to +50°C
Current DrainTransmit3A Max
Receive (Squelched)0.3A
Receive (VOL Max)0.7A
Antenna ConnectorUHF, SO-239
TRANSMITTER
Power Output8 Watts FM/AM
Frequency Response300-3000Hz
Modulated Signal DistortionInferior to 5%
Output Impedance50 ohms
RECEIVER
SensitivityLess than 1uV for 10dB (S+N)/N
Adjacent Channel Rejection60dB
IF Frequencies1st10.695MHz
2nd455KHz
Automatic Gain Control (AGC)Change in audioLess than 10dB
Output for inputsfrom 10 to 5000uV
SquelchLess than 1uV
Audio Output Power1Watts at 8 ohms less than 10% distortion
Audio Frequency Response300-3000Hz
Band and Frequency List for Anytone AT-708PLUS CB Radio
Detailed Band and Frequency List for the AT-708PLUS.

User Tips

  • Battery Care: Always remove the battery promptly after it is fully charged to prevent overcharging, which can shorten battery life.
  • Volume Adjustment: Adjust the volume to a comfortable level based on environmental noise, rather than always setting it to maximum.
  • Band Limitations: Please note that this CB radio operates in AM/FM modes and does not support LSB (Lower Side Band) or USB (Upper Side Band) transmissions.

Safety and Usage Precautions

To extend the lifespan of the equipment and ensure safety, please note the following:

Prohibited Actions:

  • Do not hold down the PTT button for a long time to transmit. Continuous transmission for more than 1 minute can cause the unit to heat up and potentially damage the amplifier.
  • Do not hold the antenna or mobile walkie talkie directly during operation, as this can cause poor antenna contact or even damage to internal components.
  • Do not replace batteries in flammable and explosive places, such as gas stations or chemical plants, as electric sparks may cause explosions.

If the power of the device you purchase exceeds 0.5W, according to China's Radio Management Regulations, you may need to apply for a radio station license when using it. Failure to do so may result in fines. Please consult your local radio management department for specific requirements.

Warning label regarding plastic bag suffocation hazard
Warning: To avoid danger of suffocation, keep plastic bags away from babies and children. Do not use this bag in cribs, beds, carriages or play pens. This bag is not a toy.

Warranty and Support

For any questions or further assistance, please contact customer service at 1669036781@qq.com.

A detailed user manual in PDF format is also available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.