Flipsky 5062

Contents

Flipsky Waterproof Brushless DC 5062 Motor 160KV 1100W

User Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient use of your Flipsky Waterproof Brushless DC 5062 Motor. This high-performance motor, featuring 160KV and 1100W maximum power, is designed for demanding aquatic applications such as surfing boats, underwater thrusters, hydrofoils, and efoils. Please read this manual thoroughly before installation and operation to ensure optimal performance and longevity of your motor.

2. Safety Information

  • Always disconnect power before performing any installation, maintenance, or inspection.
  • Ensure all electrical connections are secure and properly insulated to prevent short circuits, especially in wet environments.
  • Do not operate the motor if it appears damaged or if any wires are exposed.
  • Keep hands, hair, and loose clothing away from the propeller during operation.
  • This motor is waterproof, but prolonged submersion beyond specified limits or in corrosive liquids may cause damage.
  • Use appropriate personal protective equipment (PPE) when handling and operating the motor.
  • Ensure the motor is adequately cooled during operation to prevent overheating.

3. Package Contents

Verify that all items are present in your package:

  • Flipsky Waterproof Brushless DC 5062 Motor
  • Propeller
  • Propeller Nut
  • Propeller Pin
Flipsky 5062 Motor and Propeller Components
Figure 3.1: Motor and Propeller Components

4. Specifications

Feature Specification
Model Φ49.2×L62.0
KV Rating 160KV
Voltage Range (UR) 6-14S (LiPo cells)
Shaft Diameter Φ8 mm
Rated Power (P) 650W
Max Power (Pmax) 1100W
Rated Current (I) 18A
Max Current (Imax) 30A
Insulation Current AC500V/50Hz/1mA/3S
Resistance (R) 120mΩ
Three-phase Leads 3*14AWG (4.5mm)
Plug Type 4mm banana plug (male)
Inductance (L) 0.15mH
Internal Structure 12N/14P
Weight (W) 0.61kg

Dimensions

Technical drawing of Flipsky 5062 Motor with dimensions
Figure 4.1: Motor Dimensions and Wiring Details

Refer to Figure 4.1 for detailed dimensions including motor length, diameter, shaft length, and mounting hole patterns. The motor is equipped with 3 x 14AWG Super Flexible Silicone Wires terminating in 4mm Banana Plugs.

5. Setup

5.1 Propeller Installation

  1. Slide the propeller onto the motor shaft, ensuring the keyway aligns with the propeller pin.
  2. Insert the propeller pin through the shaft and propeller.
  3. Thread the propeller nut onto the shaft and tighten it securely. Do not overtighten.

5.2 Motor Mounting

The motor features mounting holes on its face for secure attachment to your application. Refer to Figure 4.1 for the exact mounting hole dimensions and pattern. Use appropriate fasteners that are resistant to corrosion in aquatic environments.

5.3 Electrical Connection

The motor comes with three phase leads terminated with 4mm male banana plugs. These should be connected to a compatible Electronic Speed Controller (ESC) designed for brushless DC motors and suitable for the motor's voltage and current ratings.

  • Connect the three motor phase wires to the corresponding phase outputs on your ESC. The order of connection may affect the motor's rotation direction. If the motor spins in the wrong direction, swap any two of the three phase wires.
  • Ensure all connections are firm and free from corrosion.
Flipsky 5062 Motor with long leads and banana plugs
Figure 5.1: Motor with Leads and Banana Plugs

6. Operating Instructions

  1. **Pre-Operation Check:** Before each use, inspect the motor, propeller, and all electrical connections for any signs of damage or loose parts. Ensure the motor is securely mounted.
  2. **Power On:** Connect your battery pack to the ESC. Follow the ESC manufacturer's instructions for proper power-up sequence and calibration.
  3. **Initial Test:** Perform a brief test run in a controlled environment (e.g., in water, if applicable) to verify correct motor rotation and smooth operation.
  4. **Operation:** Gradually increase throttle to achieve desired thrust. Monitor motor temperature and current draw if possible, especially during initial runs or under heavy load.
  5. **Power Off:** Always disconnect the battery from the ESC after use.

Caution: Avoid running the motor out of water for extended periods, as this can lead to overheating and damage, especially if not designed for air cooling.

7. Maintenance

  • **Cleaning:** After use, especially in saltwater, rinse the motor thoroughly with fresh water to remove salt and debris. Allow it to dry completely before storage.
  • **Inspection:** Regularly inspect the motor for any signs of wear, corrosion, or damage to the casing, shaft, and wires.
  • **Propeller Check:** Ensure the propeller is free of nicks or cracks and is securely fastened. A damaged propeller can cause imbalance and reduce efficiency.
  • **Bearing Care:** While the motor is designed for aquatic use, periodic inspection of bearings for smooth rotation is recommended.
  • **Storage:** Store the motor in a dry, cool place away from direct sunlight and corrosive materials.

8. Troubleshooting

Problem Possible Cause Solution
Motor not spinning No power to ESC; ESC not armed; loose connections; motor or ESC fault. Check battery connection; ensure ESC is armed; verify all wiring; test motor/ESC separately if possible.
Motor stutters or runs rough Incorrect ESC settings; damaged motor phase wire; propeller obstruction. Check ESC programming (timing, PWM frequency); inspect motor wires; clear propeller.
Motor overheats Overloading; insufficient cooling; incorrect propeller size; short circuit. Reduce load; ensure proper water flow for cooling; use a smaller propeller; check for internal shorts.
Reduced thrust Damaged propeller; battery low; motor or ESC losing efficiency. Inspect/replace propeller; charge battery; check motor/ESC for damage.

9. User Tips

  • **Propeller Size:** Consider the propeller size in relation to your application; some users have noted it might be smaller than expected for certain uses. Evaluate your thrust requirements carefully.
  • **Spare Parts:** If you require spare propellers or other components, please contact Flipsky customer support directly to inquire about availability.

10. Warranty and Support

10.1 Warranty Policy

The warranty period for this motor is 2 months, starting from the 7th day after the shipment date (as verified by logistic records). This warranty covers manufacturing defects.

To claim warranty service, please contact Flipsky service at flipsky_service@outlook.com. You will be required to return the item for analysis. If a manufacturing failure is confirmed, the product will be repaired or replaced free of charge. Shipping costs for returning the product are the responsibility of the customer.

10.2 Warranty Exclusions

The warranty does not cover:

  • Inability to provide proof of purchase from an authorized channel.
  • Mechanical damage to electronic components or the PCB.
  • Damage to the PCBA board due to repair soldering iron traces (excluding original cable bullet connectors).
  • Water damage or external impact damage beyond the product's specified waterproof capabilities.
  • Damage resulting from abnormal applications or use outside of product specifications.
  • Products purchased from channels other than https://flipsky.net (contact your original purchase channel for support).
  • Damage due to improper installation or modification.
  • The warranty is valid only for the original purchaser and is not transferable.

10.3 General Clarifications

  • All products are tested before shipment to ensure quality.
  • For any questions regarding VESC/Motor settings or connections, please contact Flipsky before installation.
  • Flipsky's liability under warranty will not exceed the actual purchase price of the product.
  • Repair services for out-of-warranty products are available for a reasonable charge, excluding shipping costs.

10.4 Contact Information

For technical support, warranty claims, or any other inquiries, please contact:

Email: flipsky_service@outlook.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.