Lifud LF-GIF040YS0900H

Contents

Lifud LF-GIF040YS0900H LED Driver Instruction Manual

Flicker-free Panel Light LED Driver

1. Product Overview

The Lifud LF-GIF040YS0900H is a 36W isolated constant current LED driver designed for flicker-free operation. It is suitable for Class II light fixtures, including panel lights, downlights, and spotlights. This driver ensures stable and efficient power delivery to LED modules.

Lifud LED Driver LF-GIF040YS0900H product label showing input/output specifications and certifications.

Figure 1: Lifud LF-GIF040YS0900H LED Driver

2. Safety Information

  • Always disconnect power before installation or servicing.
  • Installation should be performed by a qualified electrician in accordance with local electrical codes.
  • Ensure proper grounding where applicable.
  • Do not use the driver with incompatible light fixtures or those not certified, as this may cause fire, explosion, or other risks.
  • Man-made damage is beyond the scope of the Lifud warranty service.
  • It is recommended that the user install over-voltage protection and surge protection devices in the power supply circuit of light fixtures to ensure electrical safety.
  • The LED driver used in combination with the end device is one of the accessories of the whole light fixture, and the EMC of the whole light fixture is not only susceptible to the driver itself, but to the LED light fixture and the whole light fixture's wiring. Thus, the manufacturer of the LED light fixture should re-confirm the EMC of the whole light fixture before the whole light fixture is finished.
  • The test conditions of the circuit breaker configuration quantity are the same as those of the inrush current.
  • The PC cover, casing, and end cap for assembling the LED driver in the light fixture must meet the fire rating of UL94-V0 or above.

3. Setup and Installation

3.1. Product Terminals

Identify the input and output terminals as shown below:

Terminal Description
AC-N Input terminal of AC neutral wire
AC-L Input terminal of AC live wire
LED+ Positive electrode output of LED driver
LED- Negative electrode output of LED driver

3.2. Wiring Instructions

  1. Ensure the main power supply is OFF before making any connections.
  2. Connect the AC-N terminal to the neutral wire of your AC power source.
  3. Connect the AC-L terminal to the live wire of your AC power source.
  4. Connect the LED+ terminal to the positive input of your LED module/fixture.
  5. Connect the LED- terminal to the negative input of your LED module/fixture.
  6. Verify all connections are secure and correct before restoring power.
Datasheet page defining product terminals, providing a structure and dimensions diagram, and packaging specifications.

Figure 2: Product Definitions and Dimensions

4. Operating Instructions

Once properly installed and wired, the Lifud LF-GIF040YS0900H LED driver will automatically provide constant current power to the connected LED module. This driver is designed for flicker-free operation, ensuring stable and comfortable lighting.

  • Ensure the input voltage is within the specified range (220-240Vac).
  • The driver is designed for continuous operation within its specified environmental conditions.

5. Maintenance

The Lifud LF-GIF040YS0900H LED driver is designed for maintenance-free operation under normal conditions. However, periodic checks are recommended:

  • Ensure the driver is free from dust and debris to maintain optimal heat dissipation.
  • Periodically inspect wiring connections for any signs of loosening or damage.
  • If the driver is exposed to harsh environments, ensure its IP20 rating is sufficient for the application.

6. Troubleshooting

If you experience issues with your LED lighting system, consider the following:

6.1. No Light Output

  • Check Power Supply: Ensure the AC input power is present and within the specified voltage range (220-240Vac).
  • Check Connections: Verify all input (AC-N, AC-L) and output (LED+, LED-) connections are secure and correctly wired.
  • Open Circuit Protection: The driver has open circuit protection (<55V). If the LED load is disconnected or faulty, the driver may enter a protected state. Reconnect or replace the LED load.
  • LED Module Fault: Test the LED module with a known good driver if possible, or inspect for visible damage.

6.2. Flickering or Unstable Light

  • Input Voltage Fluctuation: Ensure the input AC voltage is stable and within the specified operating range.
  • Loose Connections: Check all wiring for loose connections.
  • Incompatible Load: Ensure the connected LED module is compatible with the driver's output specifications (33-40VDC, 900mA).

6.3. Driver Overheating

  • Ventilation: Ensure the driver is installed in an area with adequate ventilation and not enclosed in a way that prevents heat dissipation.
  • Ambient Temperature: Verify the operating ambient temperature is within the specified range (-30°C to +45°C).

6.4. Short Circuit Protection

  • The driver features hiccup mode (auto-recovery) for short-circuit protection. If a short circuit occurs on the output, the driver will attempt to recover automatically once the short is removed. Identify and rectify the short circuit in the LED load or wiring.

7. Specifications

Parameter Value
Model NumberLF-GIF040YS0900H
TypePower Supply (LED Driver)
Input Voltage220-240Vac (voltage limit: 198-264Vac)
Input Frequency50/60Hz
Max. Input Current0.28A max.
Output Voltage33-40VDC
Output Current900mA (Constant Current)
Rated Power36W
Output Power Range1 - 50W
Power Factor (PF)≥0.95
Total Harmonic Distortion (THD)≤20%
Efficiency≥88% (at 900mA-1050mA)
Flicker Index (Modulation Depth)Complies with IEEE 1789-2015 standard
IP LevelIP20
Operating Temperature-30°C to +45°C
Operating Humidity20-90%RH (no condensation)
Storage Temperature/Humidity-30°C to +80°C (6 months in Class I environment); 10-90%RH (no condensation)
Overall Appearance (L*W*H)115*41*28mm
Net Weight99g
CertificationsENEC, CB, CE, RCM, UKCA, SAA, CCC
Datasheet page presenting a table of electrical characteristics including output, input, protection, and environment details.

Figure 3: Electrical Characteristics Table

8. Warranty and Support

The Lifud LF-GIF040YS0900H LED Driver comes with a 5-year warranty (Tc≤89°C) from the date of purchase, covering defects in materials and workmanship under normal use and service conditions.

8.1. Warranty Limitations

  • The warranty does not cover damage caused by improper installation, misuse, abuse, accidents, unauthorized repairs, or modifications.
  • Man-made damage is beyond the scope of the warranty service.
  • Using incompatible light fixtures or those that have not been certified may void the warranty.

For warranty claims or technical support, please contact your original point of purchase or an authorized Lifud distributor.

9. User Tips

  • Always ensure the LED load matches the driver's specifications (voltage and current) for optimal performance and longevity.
  • Proper heat management is crucial for the lifespan of any electronic component. Ensure adequate airflow around the driver.
  • When replacing an existing driver, always match the output specifications (voltage and current) of the new driver to the original for compatibility with your LED fixture.

© 2023 Lifud. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.