1. Introduction
The OPCOM is a specialized PC-based diagnostic interface designed for Opel vehicles. This tool allows users to perform comprehensive diagnostics on a wide range of Opel models, including newer vehicles equipped with CAN-BUS based diagnostic systems such as the Vectra-C, Astra-H, and Zafira-B.
Key functionalities include reading and clearing fault codes, displaying live data streams, and performing various output tests on multiple control units within the vehicle.
2. Important Safety Information & Warnings
- System Compatibility: This device requires a computer running Windows XP or Windows 7 (32-bit only). It is NOT compatible with Windows 8 or Windows 10. Attempting to use it on unsupported operating systems may lead to malfunction or damage.
- Online Updates: DO NOT attempt to update the device firmware or software online. Online updates will permanently damage the device, rendering it inoperable.
- Anti-Virus Software: Ensure your anti-virus program is disabled during software installation and operation to prevent interference.
- Always ensure the vehicle's ignition is off before connecting or disconnecting the diagnostic interface.
3. System Requirements
- Operating System: Windows XP (32-bit) or Windows 7 (32-bit).
- Processor: Minimum 1 GHz.
- RAM: Minimum 1 GB.
- Hard Disk Space: At least 100 MB free space.
- USB Port: Available USB 2.0 port.
- Software: OPCOM Software V2014 120309A (provided on CD).
- Internet Connection: Not required for operation, and online updates are strictly prohibited.
4. Package Contents
Please verify that all items are present in your package:
- 1 x OPCOM Diagnostic Interface
- 1 x USB Cable
- 1 x Software CD (containing drivers and OPCOM software)
5. Setup Guide
5.1. Software Installation
- Before starting, ensure your computer meets the System Requirements and that your anti-virus software is temporarily disabled.
- Insert the provided Software CD into your computer's CD/DVD drive. If the CD is unreadable or damaged, please contact your seller for a download link.
- Follow the on-screen instructions to install the OPCOM software (V2014 120309A) and necessary drivers.
- Once the installation is complete, restart your computer if prompted.
5.2. Hardware Connection
- Ensure the vehicle's ignition is OFF.
- Locate the OBD-II diagnostic port in your Opel vehicle. This is typically found under the dashboard on the driver's side.
- Connect the OPCOM Diagnostic Interface to the vehicle's OBD-II port.
- Connect the other end of the USB cable to an available USB port on your computer.
- Turn the vehicle's ignition to the ON position (engine not necessarily running, but all dashboard lights should be on).
- Your computer should detect the new hardware and complete the driver installation.
6. Operating Instructions
Once the software and hardware are set up, you can launch the OPCOM software to begin diagnostics.
6.1. General Functions
- Read Fault Codes: Retrieve diagnostic trouble codes (DTCs) from various control units.
- Clear Fault Codes: Erase stored DTCs after repairs have been made.
- Live Data Display: View real-time sensor readings and operational parameters.
- Output Tests: Activate specific components (e.g., fuel pump, cooling fan) to verify their functionality.
6.2. Communication Protocols
The OPCOM interface acts as a multiplexer, selecting the appropriate pins on the OBD connector for communication:
- Serial Link (ISO9141, KW81, KW82, KWP2000): Uses PIN3, PIN7, PIN8, PIN12.
- HSCAN (High Speed CAN-BUS): Dual-wire, 500 kbps, uses PIN6-PIN14.
- MSCAN (Medium Speed CAN-BUS): Dual-wire, 95 kbps, uses PIN3-PIN11.
- SWCAN (Low Speed CAN-BUS): Single-wire, 33.3 kbps, uses PIN1.
6.3. Reading Fault Codes
When reading fault codes, the software provides:
- Full fault code text descriptions.
- Status information (Present, Not present, Intermittent).
- Options to print, save, or copy fault codes.
- Direct access to measuring blocks from the fault codes window.
6.4. Live Data (Measuring Blocks)
The program displays measuring block information from various control modules. You can customize the list of parameters to monitor. Up to 8 measuring block parameters can be displayed simultaneously. The sample rate varies depending on the communication protocol; older systems (e.g., ISO-9141-2) may be slower, while newer KWP-2000 and CAN-based units offer faster data acquisition.
7. Firmware and Software Information
- Hardware Versions: V1.70, V1.95, V1.99.
- Software Version: V2014 120309A.
- Language: English Only.
- Chipset: Features PIC18F458 and FTDI chips. Specific FTDI chip varies by version: FT232RL for V1.59, V1.65, V1.70, V1.78, V1.99; FT232RQ for V1.95.
- Firmware Update Capability: Only OPCOM FW V1.95 supports Flash Firmware updates. Other firmware versions do not support this feature.
8. Maintenance
- Keep the diagnostic interface clean and dry. Avoid exposure to moisture, dust, and extreme temperatures.
- Store the device in a safe place when not in use to prevent physical damage.
- Regularly check the USB cable and OBD-II connector for any signs of wear or damage.
9. Troubleshooting
- Q: The device stopped working after an online update.
- A: As stated in the safety information, online updates are strictly prohibited and will permanently damage the device. This damage is irreversible.
- Q: The software does not install or run on my computer.
- A: Ensure your operating system is Windows XP (32-bit) or Windows 7 (32-bit). The software is not compatible with Windows 8 or Windows 10. Also, make sure your anti-virus program is temporarily disabled during installation and operation.
- Q: The provided CD is unreadable or damaged.
- A: Please contact your seller to obtain a download link for the software and drivers.
- Q: The device connects to the computer but cannot communicate with the vehicle.
- A: Verify that the vehicle's ignition is in the ON position. Check all cable connections. Ensure no other diagnostic software is running in the background. Confirm that the correct drivers are installed for the device.
10. Specifications
| Feature | Specification |
|---|---|
| Communication Interface | OBD-II |
| Automotive Fit Type | Universal fit (for Opel vehicles) |
| Battery Included | No |
| Wireless Support | No |
| High-Concerned Chemical | None |
| Software Update | Yes (via provided software, not online) |
| Language | English |
| Software Version | V2014 |
| Hardware Version | V1.70, V1.95, V1.99 |
| Origin | Mainland China |
| Item Type | Code Readers & Scan Tools |
| Certification | NONE |
| Function | OBD2 for CAN-BUS Scanner |
| PCB Type | PIC18F458 & FTDI FT232RL/FT232RQ |
Package Dimensions & Weight:
- Length: 20 cm
- Width: 15 cm
- Height: 15 cm
- Weight: 0.2 kg
11. User Tips
- Always ensure your vehicle's battery is adequately charged before performing diagnostic procedures to avoid interruptions.
- Save diagnostic reports regularly, especially before and after making changes or clearing codes, for future reference.
- Familiarize yourself with the OPCOM software interface by exploring its menus and options before performing critical operations.
- For optimal performance and to avoid potential issues, dedicate a specific computer (running Windows XP or 7 32-bit) solely for diagnostic tasks with this tool.
12. Warranty and Support
For specific warranty terms and conditions, please refer to the information provided by your seller at the time of purchase. If you encounter any issues or require technical assistance, please contact the seller or manufacturer directly.
An additional user manual in PDF format may be available for download. Please check with your seller or refer to the product listing for a direct link to the PDF document: OPCOM User Manual (PDF).