AUTOPMALL C3

Contents

AUTOPMALL C3 Navigation Mirror HUD User Manual

OBD2+GPS Dual Mode Head-Up Display

1. Introduction

The AUTOPMALL C3 Head-Up Display (HUD) is designed to project essential driving information directly onto your windshield, allowing you to keep your eyes on the road. It supports both OBD2 and GPS dual modes, providing data such as speed, RPM, water temperature, voltage, trip distance, and navigation directions. This manual provides detailed instructions for installation, operation, and troubleshooting to ensure optimal use of your device.

Kindly Attention:

  • System Selection: Please switch to GPS system when OBD mode is not available.
  • OBD2 Mode Working Voltage: 5V~18VDC (12VDC/200mA). If the voltage is higher than 24V, please use a USB cable for GPS mode.

2. Product Overview

2.1. Package Contents

Ensure all items are present in your package:

  • C3 Head-Up Display Unit
  • OBD Cable
  • Cigarette Lighter Cable
  • English User Manual (PDF available online: User manual (PDF))
  • Cleaning Cloth
C3 HUD Accessories: Head-up display unit, cigarette lighter cable, English manual, cleaning cloth, OBD cable.
Figure 1: Package Contents

2.2. Device Components

The C3 HUD unit features the following main components:

  1. Spare interface
  2. OBD / USB cable connection
  3. Optical lens
  4. LCD display
Diagram of C3 HUD showing spare interface, OBD/USB cable connection, optical lens, and LCD display.
Figure 2: C3 HUD Component Diagram

2.3. Button Functions

The device has four buttons for control:

  • Power Switch: Long press for 2 seconds to turn off, long press again to turn on.
  • '<' Button (Short Press):
    1. To choose language and system.
    2. To switch functions in the right display area.
    3. Menu and parameter '+'.
  • '>' Button (Short Press):
    1. To select language and system.
    2. To switch functions in the left display area.
    3. Menu and parameter '-'.
  • 'M' Button (Short Press):
    1. To switch functions.
    2. To switch displays.
  • 'M' Button (Long Press):
    1. To enter into settings.
    2. To save and exit after adjustment.
Diagram showing the C3 HUD with its four control buttons labeled 1, 2, 3, 4.
Figure 3: Control Buttons

3. Setup and Installation

3.1. Physical Installation

Follow these steps to install your C3 HUD:

  1. Connect Power: Plug the OBD cable into your car's OBD socket connector, or use the cigarette lighter cable for power.
  2. Route Cable: Carefully route the wire, tucking it into the A-pillar seal to keep it tidy and out of the way.
  3. Position HUD: Connect the other end of the OBD cable to the HUD unit and place the HUD in the desired position on your dashboard, ensuring a clear view of the optical lens.
Three-step installation guide for the C3 HUD: 1. Plug into OBD socket or cigarette lighter. 2. Wire plugged into A-pillar seal. 3. Connect OBD to HUD and place it.
Figure 4: Installation Steps

3.2. Initial Power-On and System Selection

After installation, start your car. The HUD should power on automatically. If no function is displayed, check the OBD cable connection. If the OBD system cannot be connected, switch to GPS mode.

To switch to GPS system:

  1. Short press the '>' key within 5 seconds of power-on to select the GPS system.
  2. If using GPS mode with a voltage higher than 24V, ensure you are using the USB cable for power.

3.3. Mobile Device Interconnection for Navigation

The C3 HUD supports synchronized navigation information from your smartphone via Bluetooth. You will need to download the 'WiiYii' app.

  1. Download App: Search for 'WiiYii' in the Android Market (for Android 4.0 and above) or the App Store (for iPhone 5 or above).
    Screenshots of the WiiYii app showing navigation steps and interface.
    Figure 5: WiiYii App Navigation Steps
  2. Enable Bluetooth & Location: Manually turn on Bluetooth and location services on your smartphone.
  3. Connect: Open the 'WiiYii' app and click its icon. The system will automatically search for the HUD and connect.
  4. Troubleshooting Connection:
    • If the phone cannot connect, delete any previously paired Bluetooth devices and re-bind to WYHUD.
    • Turn Bluetooth off and on again, or restart your phone.
    • Ensure other phones have Bluetooth off to avoid interference.
    • Check your phone's system version for Bluetooth 4.0 compatibility (Android 4.0+, iOS 9+).
    • Ensure location services and network are active for navigation.

4. Operation

4.1. Display Modes and Parameters

The C3 HUD offers multiple display interfaces and parameters. Use the 'M' button (short press) to switch between different functions and displays.

Key Display Parameters:

  • Speed: Current driving speed (KM/H or MPH).
  • RPM: Engine Revolutions Per Minute.
  • Water Temperature (ECT): Engine Coolant Temperature.
  • Battery Voltage (VLT): Vehicle battery voltage.
  • Clock (RTC): Real-Time Clock.
  • Driving Time (MIN): Duration of current drive.
  • Driving Distance (DIS): Distance traveled during current drive.
  • Fuel Consumption (FUE): Current fuel consumption.
  • Altitude (ALS): Current altitude.
  • Satellite Numbers (GPS): Number of connected GPS satellites.
  • Oil Temperature (OIT): Engine oil temperature.
  • Turbine Pressure (TCP): Turbocharger pressure.
  • Intake Pressure (MAP): Manifold Absolute Pressure.
  • Air-fuel Ratio (A/F).
  • Dynamic Test: Includes Acceleration Test and Brake Test.
  • DTCS Status: Diagnostic Trouble Code status.
Icons representing all HUD functions including Speed, RPM, Water temperature, Battery Voltage, Clock, Driving time, Driving distance, Fuel Consumption, Altitude, Satellite numbers, Customized navigation, Mobile device interconnection, Speed camera icon, Navigation arrow direction, Automatic light adjustment, Dynamic test, Speed camera display area, Oil temperature, Turbine pressure, Air-fuel ratio, Intake pressure, KM/H MPH, Data stream, OBD system, GPS system.
Figure 6: All HUD Functions and Alarms

4.2. Multi-Alarms

The C3 HUD provides several alarms to enhance driving safety:

  • Over Speed Alarm: Triggers when vehicle speed exceeds a set value (default 150KM/h, range 5-200km/h).
  • Engine RPM Alarm: Triggers when engine RPM exceeds a set value (default 6000r/min, range 1000-8000).
  • Voltage Alarm: Triggers when battery voltage is below a set value (default 10.5V, range 10.0-15.0V).
  • High Water Temperature Alarm: Triggers when engine water temperature exceeds a set value (default 120°C, range 50-200).
  • Fatigue Driving Reminder: Alerts for prolonged driving.
  • DTCS Alarm: Alerts for Diagnostic Trouble Codes.
Diagram showing various alarms: Low voltage alarm, Water temperature alarm, Speed alarm, Speeding reminder, Engine failure alarm.
Figure 7: Safety Alarms

4.3. Settings Menu

To enter the settings menu, long press the 'M' button for 2 seconds. Use the '<' and '>' buttons to navigate and 'M' (short press) to confirm. Long press 'M' for 2 seconds to save and exit.

Available Settings:

  • Language Set: Chinese Simplified/Traditional, English.
  • Sound Switch: ON/OFF buzzer.
  • Speed Alarm: Set overspeed warning threshold.
  • Coolant Alarm: Set engine temperature alarm threshold.
  • RPM Alarm: Set engine speed alarm threshold.
  • BAT Alarm: Set battery voltage alarm threshold.
  • Speed Adjust: Calibrate speed display if inaccurate.
  • Speed Offset: Adjust speed zero point.
  • BAT Adjust: Fine-tune battery voltage display.
  • Engine Size: Set engine displacement for accurate fuel consumption.
  • Fuel Adjust: Fine-tune fuel consumption display.
  • Change Color 1/2/3: Customize display colors for speed, left area, and right area.
  • Brightness: Auto automatic light sensitive (1-8 levels).
  • CWT Unit: Temperature unit (°C/°F).
  • Speed Unit: Speed unit (KM/H/MPH).
  • Sum Distance: Synchronize total mileage with dashboard.
  • Power Off Time: Set shutdown delay.
  • Sleep Voltage: Set voltage for auto shutdown.
  • Factory Set: Restore to factory defaults.
Menu options for C3 HUD settings, including Language Set, Sound Switch, Speed Alarm, Coolant Alarm, RPM Alarm, BAT Alarm, Speed Adjust, Speed Offset, BAT Adjust, Engine Size, Fuel Adjust, Change Color, Brightness, CWT Unit, Speed Unit, Sum Distance, Power Off Time, Sleep Voltage, Factory Set.
Figure 8: Settings Menu Options

4.4. Driving Tests

The HUD can perform driving performance tests:

  • Acceleration Test: Measures the time it takes for the car to accelerate from 0 to 100 km/h.
  • Brake Test: Measures the time and distance taken to brake from a speed above 60 km/h.
Diagrams illustrating the Acceleration Test (0-100km/h) and Brake Test (100km/h-0km/h) with time and distance measurements.
Figure 9: Acceleration and Brake Tests

4.5. Car Data Scanning and Diagnosis

The HUD can scan and clear Diagnostic Trouble Codes (DTCS) and display a data stream from your car's engine.

  • Scan Fault Code: Scans the car for fault codes.
  • Clear Fault Code: Press 'M' to clear fault codes when present.
  • Read Data Stream: Shows all data from the car engine.
Diagram showing car data scanning and diagnosis process, including Scan DTCS and Clean DTCS.
Figure 10: Car Data Scanning and Diagnosis

5. Maintenance

  • Cleaning: Use the provided cleaning cloth to gently wipe the optical lens and display screen. Avoid abrasive materials or harsh chemicals.
  • Storage: If the device will not be used for more than one week, it is recommended to unplug it from the car to prevent battery drain.
  • Firmware Updates: Refer to the official product page or contact customer support for information on firmware updates.

6. Troubleshooting (FAQ)

6.1. OBD2 Mode Issues

  1. No function displayed, no power:
    Check if the OBD cable is tightly connected. Try it on another car. If the issue persists, the OBD diagnostic interface might be faulty.
  2. Only car voltage displays and automatic power off after 30 seconds:
    This indicates the product's OBD2 mode is not supported by your car (OBD I, JOBD, or cars before 2003/2007 for other regions). Switch to GPS system using the USB cable for display. Short press '>' within 5 seconds of power to select GPS system.
  3. Vehicle speed on HUD not matching speedometer:
    (1) Check if the speed unit (KM/H or MPH) is correct in settings.
    (2) Car factories may increase speed by 5-7% for safety. HUD satellite data follows international standards.
    (3) Fine-tune the speed in the settings menu (e.g., if the instrument displays 100 Km/h and HUD shows 105 Km/h, adjust the HUD value by -5).
  4. Error on fuel consumption:
    (1) Check and set the engine displacement in settings to match your car's.
    (2) If displacement is correct, fine-tune the fuel consumption setting (e.g., if equipment fuel is 0.2L higher, set parameter to 98%). Fine-tuning is optional as it's real data from the car computer.
  5. Device cannot auto shut down:
    If the RPM does not turn off after the car engine stops, set the 'Sleep Voltage' to 13.2V or 13.6V so the car can turn off after 3 minutes.
  6. Automatic start-up auto off when braking or in hybrid cars:
    (1) Set to COM mode in the 'Shutdown Voltage' menu.
    (2) Set 'Shutdown Delay' to 300 seconds (turns off after 5 minutes).
    (3) Switch to GPS system (short press '>' within 5s).
  7. Wrong operation leading to crashes:
    (1) Check for other OBD devices (parking sensor, TPMS, etc.) on the OBD2 interface.
    (2) If your car has been modified (central navigation, electronic throttle controller, etc.), this might cause crashes.
    (3) Engine start-stop, keyless entry, or remote start systems can cause crashes. Unplug other OBD devices and perform a factory reset. Switch to GPS system (short press '>' within 5s) and connect with a USB cable.

6.2. GPS Mode Issues

  1. Screen not displayed, no power:
    Check the OBD cable or car charger connections. Try plugging a USB cable into the cigarette lighter.
  2. No speed displayed:
    GPS needs time to search for satellites. Drive to an open road to acquire 5 or more satellites for normal operation.
  3. HUD cannot automatically power on or repeatedly extinguishes during driving:
    Set the 'Shutdown Voltage' to 13.0V or 12.8V (in OBD mode).
  4. Inaccurate clock:
    Enter 'System Time' in settings, use '>' to adjust, and 'M' to save.
  5. Speed is not correct:
    (1) Check speed unit settings (KM/H or MPH).
    (2) Car factory speed may be higher than real for safety. Satellite data is strictly international standards.
    (3) Fine-tune the vehicle speed in settings (e.g., if meter displays 100 Km/h and HUD shows 105 Km/h, adjust by -5).
  6. Error of travel direction:
    Satellite cannot recognize driving direction without speed display. It will normalize once speed exceeds 5KM/H.
  7. Speed still on display after car stops:
    Satellite drift can occur in underground parking, tunnels, or overpasses. Drive to an open road until satellite numbers are >5.
  8. HUD cannot be automatically shut down after car stopped:
    (1) HUD should shut down in 3 minutes (in OBD mode).
    (2) If not in 5 minutes, set 'Shutdown Voltage' to 13.5V or switch to GPS mode.
  9. App Bluetooth connection is not successful:
    (1) Check phone system version (Bluetooth 4.0+, iOS 9+, Android 4.4+).
    (2) Phone needs to search for WYHUD via Bluetooth. Open traffic.
    (3) Turn on GPS navigation positioning.
  10. App Bluetooth connection successful, no display of input address:
    Turn on location services, open your network, and check the signal. Move to a place with strong signal and re-enter the address.
  11. HUD stuck during navigation or display switch, speed display is normal:
    Turn off power-saving mode and screen-forbidden function on your phone. Keep the phone navigation page active.
  12. Navigation 10-20m from indication point:
    GPS positioning error is about 5-10 meters. It is normal for satellite signal to be 10-20 meters off when weak.

7. Specifications

AttributeValue
Brand NameAUTOPMALL
ModelC3 Car Head Up Display
Rated PowerCar HUD Head Up Display
Size Name128x116x78mm
Wire or Wirelesswired
OriginMainland China
Speed WarningSupport
MaterialABS
ColorBlack
SystemOBD2+GPS dual modes
Working voltage5~18VDC (12VDC/200mA)
Applicable modelsSuitable for all cars
Special FeatureNavigation
Display Parameters-1Speed, RPM, Water Temperature, Battery Voltage, Driving Time
Display Parameters-2Fuel Consumption, Oil Temperature, Turbine Pressure, Altitude
Ambient temperature-40°C -80°C atmospheric pressure 86-106kPa
Relative humidity10%-95% Environmental noise ≤60dB(A)
Alarm level≥30dB(A)
Product size diagram showing dimensions: 128mm (5.04in) length, 116mm (4.57in) width, 78mm (3.07in) height for the screen, and 32mm (1.38in) height for the base.
Figure 11: Product Dimensions

8. Warranty and Support

8.1. Warranty Information

The product undergoes strict testing before shipment and is carefully packaged. If the product is damaged during transit, please contact customer service before opening any dispute or leaving negative feedback. We will try our best to fix the problem.

8.2. Additional Resources

For further assistance, please refer to the comprehensive user manual available in PDF format: AUTOPMALL C3 User Manual (PDF).

9. User Tips

  • Virtual Image Distance: The virtual image distance is approximately 3 inches, providing a clear and readable display.
  • Language Support: The device supports English and Chinese for its display information.
  • GPS Signal: For accurate GPS readings, ensure your vehicle is in an open area to acquire sufficient satellite signals (5 or more satellites).
  • Speed Calibration: If the HUD speed differs from your car's speedometer, use the 'Speed Adjust' setting to fine-tune it.
  • Long-Term Storage: If the car is not used for more than a week, it is advisable to unplug the HUD device to prevent battery drain.

10. Video Demonstration

Watch this video to see the AUTOPMALL C3 HUD in action, demonstrating its speed, RPM, and navigation display features during a drive.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.