TKXEC ZK-TB21

Contents

ZK-TB21 TPA3116D2 Bluetooth 5.0 Subwoofer Amplifier Board User Manual

Model: ZK-TB21 | Brand: TKXEC

1. Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your ZK-TB21 TPA3116D2 Bluetooth 5.0 Subwoofer Amplifier Board. This 2.1 channel power audio stereo amplifier board is designed to deliver clear sound with adjustable bass and treble for both main channels and the subwoofer. Please read this manual carefully before use to ensure optimal performance and safety.

2. Specifications

Product Parameters for ZK-TB21 Amplifier Board

Figure 2.1: ZK-TB21 Product Parameters

ZK-TB21 Amplifier Board Specifications
Feature Description
Product Name 2.1 channel audio amplifier module with Tone
Product Model ZK-TB21
Bluetooth Version 5.0 (no shielding, 10 meters range)
Input Sensitivity 500mV
Audio Input AUX + Bluetooth
Channel Configuration 2.1 (Left channel + right channel + subwoofer)
Chip Solution TPA3116D2 (with AM interference suppression)
Power Range DC12~24V / 5A above (high power recommended high voltage)
Adapter Speaker 20W~100W, 4~8Ω
Output Power Max 50W @ R&L channel, Max 100W @ subwoofer
Protection Mechanism Overvoltage, undervoltage, overheating, DC detection, short circuit protection
Product Dimensions 120mm*100mm*20mm / 4.72in*3.97in*0.79in
Package Weight 256g / 0.56 lb

Note: For optimal output power, ensure sufficient audio input signal and adequate supply voltage/current. Higher supply voltage and lower speaker impedance generally result in greater output power. Always ensure the power of your adapter meets or exceeds the actual working power requirements of the amplifier.

3. Package Contents

Upon opening your package, you should find the following items:

  • ZK-TB21 Amplifier Board
  • Components for self-assembly shell
  • Screwdriver for assembly
  • Knobs for potentiometers
  • Various screws and copper pillars for assembly
ZK-TB21 Amplifier Board and assembly tools in box

Figure 3.1: Package Contents (Amplifier Board, Self-Assembly Shell Components, Screwdriver)

4. Assembly Instructions

The amplifier board comes with components for a self-assembly shell. Follow these steps to assemble the protective casing:

  1. Identify the upper cover board, lower cover board, PCB, knobs, M2*18 copper pillars, M2*4 screws, and M2*5+4 copper pillars.
  2. Attach the M2*5+4 copper pillars to the PCB.
  3. Secure the PCB to the lower cover board using the M2*4 screws.
  4. Attach the M2*18 copper pillars to the PCB.
  5. Place the upper cover board onto the M2*18 copper pillars and secure it.
  6. Install the knobs onto the potentiometers on the board.
Diagram showing the assembly steps for the amplifier board's casing

Figure 4.1: Installation Diagram for the Amplifier Board Casing

5. Setup

ZK-TB21 Amplifier Board with labeled input/output ports and controls

Figure 5.1: ZK-TB21 Amplifier Board Layout with Labeled Controls

5.1. Power Supply Connection

The power supply is crucial for the amplifier's performance. Use a DC12~24V power supply with a current of 5A or above. A power supply with low ripple is essential to prevent bottom noise and current sound. Higher voltage and current generally lead to higher power output. If using a lower voltage (e.g., 9V/12V) or lower current (e.g., 1A/2A), the output power will be limited, and sound quality may be affected.

  • Connect your DC power supply to the Power Input terminals (5.5x2.1DC head or 2P terminals) on the board.
  • Ensure the power supply voltage and current are appropriate for your speakers to avoid distortion or damage.

5.2. Speaker Connection

This amplifier supports 2.1 channel output. Ensure your speakers are compatible with the amplifier's specifications (20W~100W, 4~8Ω).

  • Connect your left and right channel speakers to the R&L Channel Output terminals. These should be full-range or mid-high frequency speakers.
  • Connect your subwoofer speaker to the Subwoofer Output terminals. The subwoofer should have a dive frequency of at least 50Hz.

5.3. Audio Input

The ZK-TB21 amplifier module supports two audio input modes: Bluetooth and AUX.

  • Bluetooth Input: This is the preferred mode. Once a Bluetooth connection is successfully established with your device, the amplifier will automatically switch to Bluetooth mode. It supports automatic reconnection.
  • AUX Input: If no Bluetooth device is connected, or if the Bluetooth connection is disconnected, the amplifier will operate in AUX mode. Connect your audio source via a 3.5mm AUX cable to the Audio Input (BT|AUX) jack.

6. Operation

Video 6.1: Demonstration of ZK-TB21 Amplifier Sound Adjustment

6.1. Main Volume Control

The MAIN VOLUME knob controls the overall output volume of the amplifier. Turning it clockwise increases the volume, and counter-clockwise decreases it. This knob affects the volume of both the left and right channels and the subwoofer simultaneously.

6.2. Left & Right Channel Tone Control

  • R&L CHANNEL TREBLE: Adjusts the high frequencies of the left and right channels. Turn clockwise to enhance treble, counter-clockwise to attenuate. The middle position is neutral.
  • R&L CHANNEL BASS: Adjusts the low frequencies of the left and right channels. Turn clockwise to enhance bass, counter-clockwise to attenuate. The middle position is neutral.

Note: If you experience sound distortion when the TREBLE or BASS knobs are turned near maximum, it indicates excessive gain. Reduce the gain by turning the knob counter-clockwise or lower the MAIN VOLUME.

6.3. Subwoofer Control

  • SUBWOOFER VOLUME: Controls the output volume of the subwoofer. Turn clockwise to increase, and counter-clockwise to decrease.
  • SUBWOOFER FREQ: Adjusts the cutoff frequency of the subwoofer, ranging from 20Hz to 200Hz. Turn clockwise to increase the frequency, and counter-clockwise to decrease.

7. Maintenance

7.1. Heat Dissipation

The ZK-TB21 amplifier board features a long-life ultra-silent fan designed to reduce the overall temperature of the module. This fan dissipates heat from the power supply, amplifier chips, and filter capacitors, which helps reduce temperature rise and its impact on sound quality, ensuring long-term stable operation of the components.

Diagram showing internal components including the fan and heat sinks

Figure 7.1: Internal Components and Heat Dissipation Features

To ensure proper heat dissipation, avoid obstructing the fan or placing the amplifier in an enclosed space without adequate ventilation. Keep the board clean and free from dust.

7.2. General Care

  • Keep the amplifier board dry and away from moisture.
  • Avoid exposing the board to extreme temperatures.
  • Handle the board with care to prevent physical damage.

8. Troubleshooting

8.1. Sound Distortion or Turbidity

  • Issue: Sound is distorted or turbid, especially at higher volumes.
  • Solution:
    • Turn down the MAIN VOLUME knob.
    • If the TREBLE or BASS knobs are turned near maximum, reduce their gain.
    • Ensure your power supply voltage is adequate. A higher voltage level may be required for louder output without distortion.
    • Verify that your speakers are within the recommended power and impedance range (20W-100W, 4-8Ω).

8.2. Sound Lag or Intermittent Power Failure

  • Issue: Sound lags or the amplifier experiences intermittent power failure.
  • Solution:
    • This often indicates insufficient input power. Replace your power supply with a more powerful one (e.g., higher current rating).
    • If the amplifier is overheating, reduce power usage or improve heat dissipation by ensuring proper ventilation.

8.3. Bluetooth Connection Issues

  • Issue: Bluetooth disconnects periodically or fails to connect.
  • Solution:
    • Ensure your Bluetooth device is within the 10-meter range of the amplifier.
    • Check for potential interference from other wireless devices.
    • Try disconnecting and reconnecting the Bluetooth device.

8.4. AUX Input Noise

  • Issue: Noise or hum is present when using AUX input.
  • Solution:
    • Verify the quality of your audio cables. Use shielded cables if possible.
    • Check the power supply for excessive ripple; a cleaner power supply can reduce noise.
    • Ensure the audio source is not introducing noise.

9. User Tips

  • Power Supply: Consider using a dedicated 24V 6A power supply for optimal performance, as some bundled power supplies may not deliver full potential.
  • Battery Power: For portable applications, a 24V 10A battery pack (e.g., 6S2P 18650) can power the amplifier and speakers effectively.
  • Sound Quality: The overall sound quality is a result of the entire audio chain. Ensure your power supply, audio source, and speakers are all of good quality and matched appropriately for the best listening experience.
  • Bass Enhancement (Advanced): Some users have reported modifying resistors R46 and R47 near the bass potentiometer to enhance bass on the satellite channels. This is an advanced modification and should only be attempted by experienced users.

10. Warranty and Support

For any issues not covered in this manual, or for further technical assistance, please contact the seller or manufacturer directly. Keep your purchase records for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.