NISSEI DG-503

Contents

NISSEI DG-503 Digital SWR Power Meter User Manual

Model: DG-503

1. Introduction

The NISSEI DG-503 Digital SWR & Watt Meter is a highly accurate instrument designed for measuring Forward Power, Reflected Power, and Voltage Standing Wave Ratio (VSWR) in radio communication systems. It features a large LCD for easy reading and a convenient control layout for straightforward operation.

Key Features:

  • Large 3.5-inch LCD digital display for clear and easy reading.
  • Simultaneous display of Forward Power, Reflected Power, and VSWR ratio with a single push button.
  • LCD backlight for improved visibility in various lighting conditions.
  • Convenient control layout for user-friendly operation.
  • Equipped with a 13.8V DC power line.
  • Supports measurements in Analog mode: CW, FM, FDMA.
  • Wide frequency range: 1.6-60MHz (HF) and 125-525MHz (VHF/UHF).

2. Package Contents

Upon opening the package, please verify that all items are present and in good condition:

  • NISSEI DG-503 Digital SWR / Watt Meter unit
  • DC 12V Power Cable
  • Operation Manual (this document, also available as a PDF: View PDF Manual)
Standard package contents of NISSEI DG-503, showing the meter, power cable, and user manual.

Figure 2.1: Standard Package Contents

3. Setup and Connections

Follow these steps to properly set up your DG-503 SWR Power Meter:

3.1 Power Connection

  1. Locate the 12V DC power connector on the rear panel of the DG-503 unit.
  2. Connect the provided DC 12V power cable to this port. Note that the power cable may require DIY termination to connect to your 12V DC power supply. Ensure correct polarity: black wire is negative (-), black/white line is positive (+).
  3. Connect the other end of the power cable to a stable 12V DC power source.
Rear panel of NISSEI DG-503 showing the 12V DC power input and antenna connectors.

Figure 3.1: Rear Panel with 12V DC Input

3.2 Radio and Antenna Connections

The DG-503 features SO239 (N-female option) connectors for your radio and antenna. Use appropriate PL259 to PL259 adapter cables (not included) for connection.

  1. Identify the "TX" (Transmitter) and "ANT" (Antenna) connectors on the rear panel. There are two sets of TX/ANT connectors, one for 1.6-60 MHz (HF) and another for 125-525 MHz (VHF/UHF).
  2. Connect your radio's RF output to the corresponding "TX" connector on the DG-503.
  3. Connect your antenna system to the corresponding "ANT" connector on the DG-503.
  4. Ensure all connections are secure to prevent signal loss and damage.
Wiring diagram showing connection of radio to TX and antenna to ANT on the DG-503 for both HF and VHF/UHF bands.

Figure 3.2: Connection Diagram

For a visual guide on unboxing and initial setup, please refer to the following video:

Video 3.1: Unboxing and Initial Connection Overview

4. Operating Instructions

4.1 Powering On/Off

  • To power on the unit, press the red "POWER" button located on the front panel.
  • To power off, press the "POWER" button again.

4.2 Band Selection

The DG-503 supports two frequency bands: HF (1.6-60 MHz) and V.UHF (125-525 MHz). Select the appropriate band using the slide switch on the front panel to match your radio's operating frequency.

Close-up of the band switch on the front panel of the DG-503, showing HF and V.UHF selections.

Figure 4.1: HF & V/UHF Band Switch

4.3 Taking Measurements

Once powered on and the correct band is selected, the large LCD will display Forward Power (FWD), Reflected Power (REF), and VSWR. The unit is designed for easy reading of these parameters.

  • Transmit a signal from your radio. The meter will automatically display the FWD, REF, and SWR values.
  • The display is backlit for clear visibility.
  • The meter is suitable for measuring CW, FM, and FDMA signals.
Front view of the NISSEI DG-503 Digital SWR Power Meter displaying FWD, REF, and SWR values.

Figure 4.2: Front Panel Display

5. Specifications

FeatureSpecification
ModelDG-503
Frequency Range1.6-60 MHz / 125-525 MHz
Calibration Point14MHz / 50MHz / 145MHz / 435MHz
Power Range0 - 200W
Accuracy(+/- 5%)
Minimum Power for SWR1W
Input/Output ConnectorSO239 (N-female option)
Weight (Net)750 g
Insertion LossLess than 0.1 dB
Testing FunctionFwd/Ref Power & VSWR ratio
Input/Output Impedance50 Ohm
Dimension (W/H/D) mm140 x 84 x 122
AccessoriesOperation Manual, 12V DC Wire
Dimensions of the NISSEI DG-503 meter: 140 mm / 5.5 inches length, 84 mm / 3.3 inches height, 122 mm / 4.8 inches width.

Figure 5.1: DG-503 Dimensions

6. Maintenance

  • Keep the device clean and free from dust. Use a soft, dry cloth for cleaning.
  • Avoid exposing the unit to extreme temperatures, humidity, or direct sunlight.
  • Ensure all connections are tight and free from corrosion.
  • Store the meter in a safe place when not in use to prevent physical damage.

7. Troubleshooting

  • No Display/No Power:
    • Check the 12V DC power connection. Ensure the power cable is securely connected and the power source is active.
    • Verify the polarity of the DC 12V wire (black negative, black/white positive).
    • Press the "POWER" button firmly.
  • Incorrect Readings:
    • Ensure the HF/V.UHF band switch is set to the correct frequency range for your radio.
    • Check all coaxial cable connections between the radio, meter, and antenna. Ensure they are tight and not damaged.
    • Verify that your antenna is properly tuned for the operating frequency.
    • Ensure the power output of your radio is within the 0-200W range of the meter.
  • No SWR Reading (or very high SWR):
    • This often indicates an issue with the antenna system. Check the antenna for damage or improper installation.
    • Ensure the antenna is designed for the frequency you are transmitting on.
    • Verify that the minimum power for SWR measurement (1W) is being met by your radio.

8. User Tips

  • Always ensure the correct band (HF or V.UHF) is selected on the meter to match your radio's operating frequency for accurate measurements.
  • For optimal performance and longevity, use high-quality coaxial cables and connectors.
  • Regularly check your antenna's VSWR to ensure efficient power transfer and prevent damage to your radio.
  • When connecting the DC 12V power cable, if you are performing a DIY connection, double-check the polarity to avoid damaging the unit.

9. Warranty and Support

For detailed warranty information and technical support, please refer to the official documentation provided with your product or contact the manufacturer/seller directly. The full operation manual is available as a PDF for your convenience: View PDF Manual.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.