COOSPO BK467

Contents

COOSPO BK467 Cadence / Speed Sensor User Manual

Dual Mode RPM Monitor for Road Bikes

1. Introduction

The COOSPO BK467 is a versatile cycling sensor designed to measure either speed or cadence in real-time. It transmits data to compatible apps or bike computers via Bluetooth 4.0 and ANT+ connectivity. This user manual provides detailed instructions to help you set up and use your BK467 sensor effectively, ensuring accurate tracking of your cycling performance.

Integrated with our self-developed patented algorithm, the BK467 tracks and captures accurate real-time cycling cadence or speed data. Its Bluetooth and ANT+ dual-band technology allows connection and data display on GPS bike computers and compatibility with most popular cycling apps.

2. What's in the Box

Please check the package contents to ensure all items are present:

  • Speed / Cadence Sensor x 1
  • Rubber Mat (Flat x 1, Curved x 1)
  • Band (Large x 2, Medium x 2, Small x 2)
  • User Manual x 1
COOSPO BK467 Sensor package contents including sensors, rubber mats, bands, and user manual.
COOSPO BK467 Sensor package contents.

3. Setup and Installation

3.1. Remove the Insulation Sheet

Before first use, you must remove the insulation sheet from the battery compartment.

  1. Twist the battery cover with a coin in the OPEN direction.
  2. Open the battery cover and remove the battery.
  3. Take out the transparent insulating sheet.
  4. Reinstall the battery and twist the cover in the CLOSE direction to secure it.
Using a coin to open the battery cover of the BK467 sensor.
Opening the battery cover.
Transparent insulation sheet to be removed from the battery compartment before first use.
Insulation sheet removal.

3.2. Mode Switching

The BK467 sensor supports both speed and cadence modes. You can switch between modes by reinstalling the battery:

  • Red LED: Indicates Speed Mode.
  • Blue LED: Indicates Cadence Mode.
COOSPO BK467 sensor showing blue LED for Cadence Mode and red LED for Speed Mode.
Red LED for Speed Mode, Blue LED for Cadence Mode.

3.3. Installation for Speed Mode

To install the sensor for speed tracking:

  1. Buckle the curved rubber mat onto the back of the sensor.
  2. Bind the sensor with the large rubber band onto the wheel axle.

3.4. Installation for Cadence Mode

To install the sensor for cadence tracking:

  1. Buckle the flat rubber mat onto the back of the sensor.
  2. Bind the sensor with the small rubber band onto the pedal crank.
Diagram illustrating installation of the BK467 sensor for speed mode on a bicycle wheel hub and for cadence mode on a pedal crank.
Installation diagrams for Speed Mode (top) and Cadence Mode (bottom).

3.5. Video Guide: How to Use the BK467 Sensor

Watch this video for a visual guide on unboxing, battery insulation removal, mode switching, and installation for both speed and cadence.

4. Operation and Connectivity

4.1. Bluetooth and ANT+ Connectivity

The BK467 sensor features dual-band Bluetooth and ANT+ technology, allowing it to connect with a wide range of devices and applications.

COOSPO BK467 sensor displaying BLE and ANT+ connectivity with various bike computers and devices.
BLE and ANT+ Connectivity with various devices.

4.2. Compatible Apps and Devices

The BK467 is compatible with most popular ANT+ bike/GPS computers and iOS/Android cycling apps, including:

  • Bike Computers: Wahoo, Garmin (Edge series), iGPSPORT, Bryton (if ANT+ compatible), XOSS G+
  • Cycling Apps: CoospoRide, Zwift, Rouvy, RidewithGPS, Peloton, Openrider, TrainerRoad, Strava, Nike+, Endomondo, Runtastic Pro, Wahoo Fitness, ONELAP, BKOOL, TACX

4.3. CoospoRide App Instruction

  1. Search for "CoospoRide" in Google Play or the App Store and install the app.
  2. Enable Bluetooth and necessary permissions on your phone.
  3. Open CoospoRide > Me > Devices > Add Devices > App Binding Sensors > Speed or Cadence.
  4. Find the BK467 Bluetooth ID and select it to connect.

Note: Do not pair the sensor directly in your phone's Bluetooth settings. Always pair through the compatible cycling app.

Smartphone screens showing the CoospoRide APP interface with speed, distance, heart rate, and cadence data, alongside the BK467 sensor.
Training with CoospoRide APP.

5. Specifications

AttributeValue
Model NumberBK467
Stopwatch and AccessoriesSpeed And Cadence Dual Sensor
Brand NameCOOSPO
MaterialABS
Weight9.5g
Battery Life500 hours
Battery TypeCR2032 220mAh
Waterproof LevelIP67
Wireless ConnectivityBluetooth & ANT+
Wireless Signal StrengthANT+: 10m, Bluetooth: 25m
Size41 x 34 x 10 mm
Max Speed120 km/h
Max Cadence300 rpm
Working Temperature-10°C ~ 50°C
ColorBlack
CertificationCE, FCC, RoHS, pse
Product parameter table for COOSPO BK467 sensor, showing dimensions, weight, battery life, wireless connectivity, max speed/cadence, waterproof rating, and working temperature.
Detailed product parameters.

6. Maintenance

6.1. Waterproofing

The BK467 sensor has an IP67 waterproof rating, meaning it is protected from dust and can withstand immersion in water up to 1 meter for 30 minutes. You can ride without fear of rain or splashes.

COOSPO BK467 sensor with water splashing, illustrating its IP67 waterproof rating.
IP67 Waterproofing.

6.2. Cleaning

Wipe the sensor with a soft, damp cloth as needed. Do not use abrasive cleaners or solvents.

7. Battery Information

The BK467 uses a replaceable CR2032 coin cell battery, providing up to 500 hours of ride time.

COOSPO BK467 sensor with its battery compartment open, showing a CR2032 coin cell battery, highlighting its 500-hour battery life.
CR2032 battery for 500 hours of use.

7.1. Battery Replacement

To replace the battery, follow the steps for 'Remove the Insulation Sheet' (Section 3.1) to open the battery cover, replace the CR2032 battery, and then securely close the cover.

7.2. Battery Safety Statement

WARNING: INGESTION HAZARD

  • This product contains a button cell or coin battery.
  • DEATH or serious injury can occur if ingested.
  • A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
  • KEEP new and used batteries OUT OF REACH of CHILDREN.
  • Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death.
  • Call a local poison control center for treatment information.
  • Nominal battery voltage: 3V.
  • Do not force discharge, recharge, disassemble, heat above 45°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
  • Ensure the batteries are installed correctly according to polarity (+ and -).
  • Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

8. User Tips

  • Dual Tracking: If you wish to track both speed and cadence simultaneously, you will need to purchase and install two separate BK467 sensors, one configured for speed mode and the other for cadence mode.
  • App Pairing: Always pair the sensor through your cycling app (e.g., CoospoRide) and not directly through your phone's Bluetooth settings.
  • Spinning Bikes: It is not recommended to use the sensor on spinning bikes, as the magnetism and metal plates of the bike can interfere with the sensor's signal, leading to inaccurate readings.
  • Automatic Activation: Once installed and in the correct mode, the sensor automatically starts transmitting data when you begin cycling (spinning the wheel for speed or the pedal crank for cadence). There is no need to remove the battery to activate it each time.

9. Troubleshooting

  • Inaccurate Readings: If you experience inconsistent or inaccurate readings, especially on indoor trainers or spinning bikes, check for potential magnetic interference. Ensure the sensor is securely mounted and the correct mode (speed/cadence) is selected.
  • Connectivity Issues: If the sensor is not connecting to your device or app, ensure it is not paired directly via your phone's Bluetooth settings. Remove it from your phone's Bluetooth list if present, and then try pairing again through the compatible cycling app.
  • Sensor Not Detected: Make sure the sensor is active. For speed mode, spin the wheel; for cadence mode, rotate the pedal crank. The sensor needs movement to activate and transmit data.
  • Battery Compartment: If the battery compartment does not close securely, stop using the product immediately, remove the batteries, and keep them away from children.
  • General Malfunction: If the product is operating improperly despite following all instructions, please contact COOSPO support for assistance.

10. FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

11. Warranty and Support

For product support, warranty information, or if your product is operating improperly, please contact COOSPO customer support. Product must be returned to the manufacturer for any service or repair.

12. Disposal Information

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.