Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your ISUDAR Android 10.0 Car Radio. Please read this manual thoroughly before using the product to ensure proper functionality and safety. This multimedia system is designed to enhance your driving experience with advanced features like navigation, multimedia playback, and smartphone integration.
Safety Precautions
- For any issues during installation or usage, please contact our after-sales support.
- Please install this product under professional guidance, as it involves electronic equipment and automotive accessories that may pose risks such as electric shock, injury, or other hazards if handled by untrained individuals.
- Ensure the power is disconnected during installation.
- It is highly recommended to seek professional help for the installation or servicing of this product, as it involves electronic equipment and automotive accessories that may pose risks such as electric shock, injury, or other hazards if handled by untrained individuals.
- This product is designed for vehicles with a 12V DC power system only. Do not install it on vehicles with a different power supply, as it may damage the product or cause a fire due to over-voltage.
- Turn off the car and disconnect the positive battery terminal before installation. Insulate all wires properly after installation to prevent short circuits that can lead to product damage or fires.
- Avoid using the car audio system for an extended period after turning off the engine to prevent draining the battery power.
- If the product gets exposed to water damage or foreign matter while driving, park the vehicle in a safe location, turn off the ignition switch (ACC OFF) immediately, and consult your dealer or customer service. Do not use the product in this condition, as it may result in fire, electric shock, or other failures.
- In case of smoke, strange noises, unusual odors, or any other abnormal signs during normal use, immediately turn off the power and consult your dealer or customer service. Do not use the product in this condition, as it may result in fire, electric shock, or other failures.
- Please place the product out of reach of children to avoid unnecessary harm.
- The manufacturer reserves the right to provide the final explanation.
Setup and Installation
Wiring Diagram
The following diagram illustrates the general wiring connections for the ISUDAR car radio. Ensure all connections are secure and correctly matched to your vehicle's wiring harness.

Image: Back view of the ISUDAR car radio showing various ports and connections.
The package includes essential cables and accessories for installation:

Image: Included cables and accessories: Power cable, Radio antenna, 4G Antenna, Original USB adapter, RCA cable, Camera input, USB cable, CANBUS, GPS antenna.
If your package includes the CANBUS box, please connect the CANBUS port to the socket on the car radio.
Note: The Camera Input, WiFi, and Bluetooth Antenna Ports must be installed. Otherwise, the WiFi and Bluetooth signal reception will be poor.
If your car has a JBL or other amplifier system, you may need another power cord adapter or a more complicated wiring method. Please contact our after-sales support for assistance.
Power Plug Definition
Refer to the table below for the definition of each pin on the power connector:
| Pin | Function | Pin | Function |
|---|---|---|---|
| 1. GND | GND | 9. FR- | Front Right Speaker- |
| 2. B+ | Battery +12V | 10. RL- | Rear Left Speaker- |
| 3. ACC | ACC | 11. FR+ | Front Right Speaker+ |
| 4. ILL | Illumination | 12. RL+ | Rear Left Speaker+ |
| 5. BACK UP | Camera Back up | 13. FL- | Front Left Speaker- |
| 6. WHEEL1 | Steering Wheel Control 1 | 14. RR+ | Rear Right Speaker+ |
| 7. WHEEL 2 | Steering Wheel Control 2 | 15. FL+ | Front Left Speaker+ |
| 8. ANT+12V | Antenna Power | 16. RR- | Rear Right speaker- |
GPS Antenna Installation
The GPS Antenna is recommended to be installed on the dashboard or below the windshield for optimal signal reception.

Image: Diagram showing recommended GPS antenna placement on the dashboard or below the windshield.
CANBUS Setup
Setting the correct CANBUS type allows the car radio to better integrate with the original vehicle information system. This step is only necessary if your car radio includes a CANBUS Box and requires setup. If not, you can skip this step entirely.
Steps to set up CANBUS:
- Connect the device to Wi-Fi.
- Go to: Settings > Factory (Code: 123456) > Select models.
- Select: CanBox > Cars for > Models for > Config.
For example, if you purchased a car radio for a Jeep Renegade, and the CANBUS box shows the brand SS (Simple Soft), then choose: 03: Simple Soft > 87: JEEP > 11: 16 Renegade > LowConfig.

Image: Screenshots of the CANBUS setup interface showing options for car model and configuration.
Reverse Camera Connection
For Original Camera: Just connect the yellow Port "A" to the yellow Port "B" as shown in the picture. "A" is Reverse Camera Output, "B" is Reverse Camera Input.
For Aftermarket Reverse Camera (With Canbus):
- Connect the yellow port "B" to the yellow port "C". The Camera red wire (2) connects with the power cable wire "BACK" or "Reverse" (1). (Camera Back UP: The 5th Pin on the "Power Connector" is the brown or pink wire.)
- The red wire (3) connects with red wire (4). The black wire (5) connects with the Car reversing light negative electrode.
For Aftermarket Reverse Camera (Without Canbus):
- Connect the yellow port "B" to the yellow port "C". The Camera red wire (2) connects with the power cable wire "BACK" or "Reverse" (1). (Camera Back UP: The 5th Pin on the "Power Connector" is the brown or pink wire.)
- The red wire (3) connects with red wire (4) and connects with the Car reversing light positive electrode. The black wire (5) connects with the Car reversing light negative electrode.

Image: Wiring diagram for reverse camera connection.
Operating Instructions
Multimedia Playback
The unit supports various multimedia playback options including USB music, online music streaming (Spotify), and online video (YouTube).

Image: Car radio displaying YouTube interface with various video thumbnails.

Image: Car radio displaying Spotify interface with music playback controls and playlists.
The device features 3 channels of USB input (for T72 series) to support U-flash disk input for music and video playback, and can also support hard disk input up to 2TB.

Image: Close-up of three USB input ports.
Phone Connectivity (CarPlay, Android Auto, Bluetooth)
Built-in wireless Apple CarPlay and wired Android Auto allow seamless integration with your smartphone for maps, calls, messages, and music.

Image: Car radio displaying Apple CarPlay and Android Auto interfaces side-by-side.
Bluetooth 5.0 provides hands-free calling and music streaming with faster transfer rates and reduced delay. The unit includes a built-in microphone and supports phone book access.

Image: Diagram illustrating Bluetooth 5.0 connectivity with increased transmission rate and distance.
DSP Sound System
The built-in DSP (Digital Sound Processor) enhances audio quality, providing smoother treble, richer midrange, and fuller bass. Equalizer and position adjustment features are available for a customized audio experience.

Image: Car radio displaying DSP equalizer settings and sound field adjustments.
ADAS USB DVR
The ADAS (Advanced Driver-Assistance Systems) USB DVR promotes safe driving by supporting rear-end warning and lane departure warning. (Note: DVR is not included and must be purchased separately).

Image: Car radio displaying ADAS warnings for lane departure and front collision on the screen.
Rear View Camera
The unit supports AHD/RCA rear view cameras with reversing lines for enhanced safety during reversing maneuvers.

Image: Car radio displaying a rear view camera feed with parking guidelines.
Voice Control
The device supports voice control for a safe and intelligent driving experience. A passcode may be required to activate this feature.

Image: Car radio displaying voice control interface with various language options.
System Settings
Steering Wheel Control Settings
- Click the Steering Wheel icon to open the settings page.
- Click "START", press the corresponding button on the screen, and then press the physical button on the steering wheel. After learning, the button will be highlighted.
- After setting all the necessary buttons, click "END" to complete and save.
Note: For car radios equipped with CANBUS, the steering wheel control buttons are directly decoded by CANBUS and do not require setting in this application. If your car radio is equipped with CANBUS, but the steering wheel control buttons still do not work after setting the CANBUS type, please contact after-sales support for reset instructions.
Logo Setting
You can customize your favorite startup image by adding a boot logo:
- Prepare the image you want to add according to the following requirements:
- Bitmap: 32bit;
- Resolution: $1024^{*}600$, $1280^{*}720$, or other (depending on your screen resolution);
- Format: BMP, PNG, JPG.
- Copy the logo image to the USB flash drive.
- Insert the USB flash drive into the USB port of the car radio, so that the car radio can read the USB flash drive and load it normally.
- Click "Settings > Factory (Code: 123456) > LOGO Setting", enter the logo setting option, the logo image in the USB will be displayed at the bottom. Select the image and click "Logo setting".
Animation Boot Logo
You can customize your favorite startup animation:
- Prepare the animation you want to add according to the following requirements:
- Bitmap: 32 bit;
- Resolution: $1024^{*}600$, $1280^{*}720$, or other (depending on your screen resolution);
- Format: Zip.
- Copy the boot animation compressed package to the USB root directory interface.
- Insert the U-disk into the device USB port, allowing the device to read the U-disk.
- Click on "Boot Animation > Pull down the status bar and click the "Menu" > An import box will pop up > Click "Import from external storage" and a password box will pop up > Enter the password "Topway". The Animation in the USB will be displayed. Select the zip and click "Confirm".
Radio Setting
- Adjust the radio reception area: Settings > Factory (Code: 123456) > Select radio region > Default Radio Area.
- RDS: Settings > Factory (Code: 123456) > Config info > RDS > ON/OFF.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the screen and exterior of the unit. Avoid using abrasive cleaners or solvents.
- Software Updates: Periodically check for software updates to ensure optimal performance and access to new features. Follow the instructions provided with the update package.
- Environmental Conditions: Avoid exposing the unit to extreme temperatures, direct sunlight for prolonged periods, or excessive moisture.
Troubleshooting (FAQ)
- Q: Why does the music stop when reversing?
- A: For safety reasons, music playback is paused during reversing. You can adjust the volume control in Settings > Reverse > Reversing volume control.
- Q: How to set up automatic connection to CarPlay after Bluetooth connection?
- A: Go to Settings > General > Application self start > Tlink5.
- Q: How to change between Celsius and Fahrenheit units?
- A: First, connect your car stereo to your phone's hotspot or WiFi. Then, open the weather app. Click the gear icon in the top right corner and select your preferred temperature unit. To switch the air conditioning temperature unit: Settings > Original > TEMP norm > Fahrenheit/Centigrade > confirm.
- Q: How to change the speed unit?
- A: Follow the path below to modify the settings: Click the "Theme" APP icon > Click the gear icon in the upper right corner > Plugin > Speed unit.
- Q: Why is the time or time zone not updating automatically?
- A: Follow this path to set it: Settings > System > Date & Time, connect your car stereo to your phone's hotspot or WiFi and then open the "Set time automatically".
- Q: Why is my weather information and location not updated?
- A: You need to connect the car stereo to your mobile phone hotspot or WiFi, and the weather information and location will be updated online.
- Q: The touch screen is not sensitive or the touch position is wrong.
- A: Find a wired mouse and connect it to the USB port, then use the mouse cursor to click the following path to enter the settings: Settings > Factory (Code:123456) > Touch area key > POSITION, Then select "CALIBRATION", last you need to click the screen position with your finger instead of clicking the mouse.
- Q: How to use the picture-in-picture function?
- A: Settings > General > Video suspension window > ON.
- Q: If I don't have a factory-installed rearview camera and don't want the reversing image to be displayed when reversing, how do I turn it off?
- A: Settings > Factory (Code: 123456) > Reverse Mode > Prohibit reversing.
- Q: How to change the language?
- A: Settings > More > System > Languages > System Languages.
Specifications
| Feature | Specification |
|---|---|
| Operating System | Android 10.0 OS |
| RAM | 8G (various configurations available) |
| ROM | 128G (various configurations available) |
| CPU | Octa Core (2 x Cortex-A75, 6 x Cortex-A55) |
| GPU | Dual Core (ARM Mali G52) |
| Display Size | 10.1" |
| Resolution | QLED 1280*720 |
| Power Output | 4*48W |
| Voltage | 12 V |
| Item Weight | 2kg |
| Max External Memory | 1tb |
| Material | Metal and Plastic |
| Din Size | One Din |
| Interface | ISO |
| Special Features | Wifi function, Support steering wheel control, Support 3G Network, Support 4G Network, Support Can-Bus, Built-in GPS, Mobile Phone, MP3 players |
| Digital Media Format | Mp3, MP4, WMA, JPEG |
| OSD Language | Arabic, Polish, Boolean text (Dutch South Africa), Danish, German, Russian, French, Filipino, Finnish, Korean, Dutch, Catalan, Czech, Romanian, Portuguese, Japanese, Thai, Turkish, Ukrainian, Hebrew, Greek, Spanish, Hungarian, Italian, Hindi, Indonesia, English, Vietnamese |
| Amplifier Chip | TDA7851 (ST7388 for 4+32G & 4+64G versions) |
| Radio Chip | TDA7708 |
| Europe Digital Audio Broadcasting (DAB) | Optional |
| WIFI | Support |
| OBD | Support |
| USB DVR | Support |
| Original Parking Radar Displaying | Support |
| Rear view camera input | Support |
| Front camera input | Support |
| RDS | Support |
| For Vehicle Brands/Model | Volkswagen Passat (2012, 2013, 2014, 2015) |
User Tips
- For steering wheel controls on VW Passat B6, ensure proper configuration in settings.
- Original GPS antenna with Fakra connector works without issues.
- If the unit goes to sleep mode after turning off the engine, it should resume the last program when restarted.
- For factory cameras, an adapter might be needed.
- To activate A/C information display, check settings or contact seller for specific Passat B7 activation.
- If experiencing a black screen, try pressing the RST button, check 12V power, and inspect fuses. Ensure all wiring (BATT+/ACC/GND) is secure.
- For no sound with an amplifier system, verify power cable compatibility, connect AUX cables, ensure the blue AMP Control wire is connected, and enable 'Always on' in the Fan app.
- To enable video playback while driving (disabled for safety), adjust 'Brake setting' in Factory settings (Code: 8888).
- Music stops when reversing for safety; adjust volume control in settings if needed.
- To set up automatic CarPlay connection, ensure 'Application self start' is enabled for Tlink5.
- To change temperature units (Celsius/Fahrenheit), connect to Wi-Fi, open the weather app, and adjust in settings. For A/C display, check 'Original > TEMP norm' in settings.
- To change speed units, go to 'Theme' APP > gear icon > Plugin > Speed unit.
- If time/time zone is not updating, connect to Wi-Fi, then go to 'Settings > System > Date & Time' and enable 'Set time automatically'.
- Weather info and location require mobile phone hotspot or Wi-Fi connection to update.
- If the touch screen is unresponsive or inaccurate, connect a wired mouse, go to 'Settings > Factory (Code:123456) > Touch area key > POSITION', then select 'CALIBRATION' and tap the screen with your finger.
- To use picture-in-picture, enable 'Settings > General > Video suspension window > ON'.
- To disable reversing image if no factory camera, go to 'Settings > Factory (Code: 123456) > Reverse Mode > Prohibit reversing'.
- To change language, go to 'Settings > More > System > Languages > System Languages'.
Warranty and Support
For any issues or questions regarding your ISUDAR car radio, please contact our after-sales support team. We are committed to providing assistance for installation, troubleshooting, and general inquiries.
Contact Information:
- Email: xyl-supports@aliyun.com
For detailed item guides and documents, please refer to the User Manual (PDF) available at this link.


