Heltecbms 4S 100A 14.8V 12.8V lithium battery protection Board

Contents

Heltecbms 4S 100A BMS Lithium Battery Protection Board User Manual

Model: 4S 100A 14.8V 12.8V lithium battery protection Board

Brand: Heltecbms

1. Introduction

This manual provides detailed instructions for the Heltecbms 4S 100A Battery Management System (BMS) protection board. This board is designed to protect 4-cell lithium-ion (14.8V) or lithium iron phosphate (12.8V) battery packs, ensuring their safe and efficient operation. It features a balanced version with a split port for charging and discharging.

Heltecbms 4S 100A Balance BMS board with included balance wires.
Figure 1: Heltecbms 4S 100A BMS Board with Balance Wires

2. Safety & Warnings

Read all instructions carefully before use to ensure safety and prevent damage to the device and connected components.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • This product kit does not include batteries. Batteries must be purchased separately.
  • Do not intentionally short circuit the board or battery pack.
  • Ensure correct wiring sequence to prevent board damage. Reversing connections can lead to a high incidence of board burning.
  • Copper connections are recommended for high current applications. Soldering thick copper can be difficult and high temperatures can damage components.

3. Components & Package Contents

The package typically includes:

  • 1 x Heltecbms 4S 100A Battery Protection Board
  • 1 x Set of Balance Wires (multi-colored, for cell voltage collection)
Angled view of the 4S 100A BMS board and balance wires.
Figure 2: BMS Board and Balance Wires

4. Setup & Installation

Follow these steps carefully to install the BMS board. Do not plug the collection cable into the protective board socket initially to prevent short circuits and electrostatic discharge.

Wiring Sequence:

  1. Step 1: Weld the main line B-

    Weld the thick wire B- of the protective plate firmly to the total negative pole at the end of the battery pack. This is the first and crucial connection.

  2. Step 2: Weld voltage collection cables one by one (balanced cables)

    Connect the balance wires in sequence, starting from the leftmost end (B0) which corresponds to the total negative pole (B-).

    • B0: Connect to the Battery negative pole.
    • B1: Connect to the positive pole of the first string (intermediate connection point between the first and second cells).
    • B2: Connect to the 2nd string positive electrode (middle connection point between the 2nd and 3rd cells).
    • B3: Connect to the 3rd string positive electrode (middle connection point between the 3rd and 4th cells).
    • B+: Connect to the last string's positive electrode (total positive electrode of the battery pack).
Detailed wiring diagram for the 4S BMS board showing connections for charge/discharge and battery cells.
Figure 3: BMS Wiring Diagram

Important Precautions:

  • Strictly follow the diagram for wiring.
  • After connecting the balance wires, charge the battery pack first. This will enable the output.
  • When connecting 4 sets of batteries in series, ensure that the voltage of each set of batteries is the same. If they are different, please fill each set of batteries separately and use them in series.

5. Operating Principles

The Heltecbms 4S 100A BMS provides comprehensive protection for your battery pack:

  • Overcharge Protection: Prevents cells from being charged beyond their safe voltage limits.
  • Over-discharge Protection: Stops discharge when cell voltage drops below a safe minimum, preventing damage.
  • Overcurrent Protection: Disconnects the load if the discharge current exceeds the safe limit.
  • Short Circuit Protection: Immediately disconnects the load in case of a short circuit, with a delay for self-recovery.
  • Balance Function: Actively balances the voltage across individual cells during charging to ensure all cells are equally charged, prolonging battery life.

Note on Charging:

For optimal balance and consistency, it is recommended to charge with a switching power supply that provides a voltage of 17V for 14.8V Lithium batteries or 15V for 12.8V LiFePO4 batteries. The equalization current of the IC is approximately 65mA. Many chargers may stop detecting current below 100mA. If cells are unbalanced, this can lead to voltage discrepancies. The working principle of this protection board involves negative pole protection, which may result in a voltage drop of 0.1-0.3V. This is normal and can be reduced by cycling (charging and discharging) the battery pack several times.

Avoid using a 16V power supply for 4-string ferric phosphate batteries (12.8V nominal), as it will not fully charge the battery to 16.8V and the protection board will not engage, leading to continuous charging and potential long-term battery life issues. Similarly, for 14.8V Lithium batteries, avoid using a 14V power supply for the same reasons.

6. Specifications

The Heltecbms 4S 100A BMS is available in versions suitable for 14.8V Lithium (3.7V nominal per cell) and 12.8V Lithium Iron Phosphate (3.2V nominal per cell) battery packs.

6.1. Basic Parameters (4S 14.8V Lithium Battery Protection Board)

Table of basic parameters for 4S 14.8V Lithium battery protection board, including current, charge, overcharge, over-discharge, overcurrent, short circuit, temperature protection, internal resistance, power consumption, operating temperature, and size.
Figure 4: Specifications for 4S 14.8V Lithium Battery BMS
Basic ProjectSpecificationUnitRemarks
Current
Continuous discharge current100AAttention temperature
Instantaneous discharge current120A
Charge
Charging voltageLithium battery charger 16.8VVSwitching power supply 17-18V
Charging current10(MAX)A
Overcharge Protection
Overcharge detection voltage4.28±0.05Vsingle core
Overcharge protection delay0.5S
Overcharge release voltage4.08±0.05Vsingle core
Electricity Balance
Power balance detection voltage4.2 ±0.05V
Power balance release voltage4.2 ±0.05V
Power balance current45mA
Over-discharge Protection
Over-discharge detection voltage2.5±0.08V
Over-discharge detection delay0.1S
Over-discharge release voltage2.9±0.1V
Overcurrent Protection
Overcurrent detection voltage150mV
Overcurrent detection delay40A
Overcurrent protection current120±10
Overcurrent protection release conditionDisconnect load
Short Circuit Protection
Short circuit protection conditionExternal load short circuitforbidden short circuit
Short circuit detection delay250uS
Short circuit protection release conditionDisconnect load
Temperature Protection
Temperature protection/°Ccan set Temperature Switches
Internal Resistance
Main circuit conduction internal resistance≤20mΩ
Own Power Consumption
Working current≤30uA
Sleep current≤20uA
Operating Temperature
Temperature range(-20°C, +80°C)
Size
Size70*60*8.5mm

6.2. Basic Parameters (4S 12.8V Lithium Iron Phosphate Battery Protection Board)

Table of basic parameters for 4S 12.8V Lithium iron phosphate battery protection board, including current, charge, overcharge, over-discharge, overcurrent, short circuit, temperature protection, internal resistance, power consumption, operating temperature, and size.
Figure 5: Specifications for 4S 12.8V Lithium Iron Phosphate Battery BMS
Basic ProjectSpecificationUnitRemarks
Current
Continuous discharge current100A
Instantaneous discharge current120A
Charge
Charging voltageLithium battery charger 14.8VVSwitching power supply 15-16V
Charging current10(MAX)A
Overcharge Protection
Overcharge detection voltage3.75 ±0.05Vsingle core
Overcharge protection delay1300S
Overcharge release voltage3.6 ±0.05Vsingle core
Electricity Balance
Power balance detection voltage3.6 ±0.05V
Power balance release voltage3.59±0.05V
Power balance current58mA
Over-discharge Protection
Over-discharge detection voltage2.1±0.08V
Over-discharge detection delay145S
Over-discharge release voltage2.3±0.1V
Overcurrent Protection
Overcurrent detection voltage200mV
Overcurrent detection delay20A
Overcurrent protection current120±10
Overcurrent protection release conditionDisconnect load
Short Circuit Protection
Short circuit protection conditionExternal load short circuitforbidden short circuit
Short circuit detection delay300uS
Short circuit protection release conditionDisconnect load
Temperature Protection
Temperature protection/°Ccan set Temperature Switches
Internal Resistance
Main circuit conduction internal resistance≤20mΩ
Own Power Consumption
Working current≤30uA
Sleep current≤20uA
Operating Temperature
Temperature range(-20°C, +80°C)
Size
Size70*60*8.5mm

7. User Tips

  • This BMS is highly recommended for building high-capacity power banks due to its robust protection features and balancing capabilities.
  • The board includes a balancing function to maintain cell voltage equality, which is crucial for battery longevity and performance.

8. Troubleshooting

  • No Output After Wiring: Ensure the balance wires are connected correctly and then charge the battery pack first. The output will activate after initial charging.
  • Unbalanced Cell Voltages: If connecting multiple battery sets in series, ensure each set has the same voltage. If not, charge each set separately to balance them before connecting in series. A group with the fastest voltage drop during discharge indicates a poor battery.
  • Unexpected Voltage Drop: A voltage drop of 0.1-0.3V across the protection board is normal due to its negative pole protection design. This can be reduced by cycling (charging and discharging) the battery pack several times.
  • Board Burning: This is often caused by incorrect wiring, especially reversing the standard wiring sequence. Always double-check connections before applying power.

9. Maintenance

  • Keep the BMS board clean and dry to prevent corrosion and short circuits.
  • Avoid exposing the board to extreme temperatures or humidity.
  • Regularly inspect wiring for loose connections or damage.
  • If temperature control is desired, ensure proper installation of external temperature switches as indicated on some board versions (e.g., HX-3S4S-D1 REV1.1).
BMS board with annotation indicating where to add temperature control, showing the HX-3S4S-D1 REV1.1 model.
Figure 6: Temperature Control Point on BMS Board

10. Warranty & Support

Manufacturer Information:

  • Company: chengdu heltec energy Technology Co., Ltd
  • Address: No.16th Chenghong Rd., Chengdu, SiChuan, China.
  • Email: echo@heltec-bms.com

EU Authorized Representative:

  • Representative: eVatmaster Consulting GmbH
  • Address: CN-Bettinastr.30, 60325 Frankfurt am Main, Germany
  • Email: contact@evatmaster.com
  • Tel: 0049-6995179070

If you have any questions or require support, please contact the manufacturer or their authorized representative.

An official user manual in PDF format is available for download: User Manual (PDF)

11. Production & Testing Overview

The Heltecbms 4S 100A BMS boards undergo a rigorous manufacturing and testing process to ensure quality and reliability.

Video 1: Manufacturing and Testing Process of Heltecbms BMS Boards. This video demonstrates the automated assembly lines and manual quality control checks, including voltage, current, and aging tests, ensuring each board meets performance standards.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.