KKMOON DDM15SC

Contents

DDM15SC Digital 1P DIN-Rail Energy Meter

Model: DDM15SC | Brand: KKMOON

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your DDM15SC Digital 1P DIN-Rail Energy Meter. This electronic KWh meter is designed for measuring single-phase active energy with high accuracy and reliability. It features a large LCD digital display for clear readings of electricity consumption, voltage, current, and power.

Front view of the DDM15SC Digital Energy Meter

Figure 1: Front view of the DDM15SC Digital Energy Meter, showing the LCD display and terminal connections.

2. Safety Information

Please read and understand all safety instructions before installing or operating this device. Failure to follow these instructions may result in electric shock, fire, or personal injury.

  • Installation and maintenance should only be performed by qualified personnel.
  • Ensure the power supply is disconnected before any installation or wiring work.
  • Do not operate the device if it appears damaged.
  • Observe all local and national electrical codes.

3. Setup and Installation

The DDM15SC energy meter is designed for 35mm DIN Rail mounting.

3.1 Mounting

Mount the energy meter onto a standard 35mm DIN rail in a suitable electrical enclosure. Ensure sufficient space for wiring and ventilation.

Side view of the energy meter showing 35mm DIN Rail installation

Figure 2: Side view of the energy meter, indicating the 35mm DIN Rail installation feature.

3.2 Wiring Methods

The meter supports two primary wiring methods: Up-out and Down-in, and Up-in and Down-out. Always ensure correct Live (L) and Neutral (N) connections.

Wiring diagram showing both Up-in and Down-out and Up-out and Down-in methods for connecting the energy meter with a power switch and air circuit breaker.

Figure 3: Wiring diagram illustrating the two supported connection methods. The top diagram shows 'Up-in and Down-out' where the Live and Neutral lines enter from the top and exit from the bottom. The bottom diagram shows 'Up-out and Down-in' where the Live and Neutral lines enter from the bottom and exit from the top. Both diagrams show connections to a power switch and an air circuit breaker.

  • Up-out and Down-in: Power input from the bottom terminals, power output from the top terminals.
  • Up-in and Down-out: Power input from the top terminals, power output from the bottom terminals.

Connect the Live (L) and Neutral (N) wires according to the chosen wiring method and the markings on the meter. Ensure all connections are secure to prevent loose contacts and potential hazards.

4. Operating Instructions

Once properly installed and powered, the DDM15SC energy meter will automatically begin measuring and displaying electrical parameters on its LCD screen.

4.1 LCD Digital Display

The large LCD digital display cycles through various readings, providing real-time information on your electricity usage:

  • KWh: Total electricity consumption in kilowatt-hours.
  • U (V): Current voltage in Volts.
  • I (A): Current amperage in Amperes.
  • P (W): Instantaneous power in Watts.
Close-up of the LCD digital display showing KWh, Voltage, Current, and Power readings.

Figure 4: Close-up of the LCD digital display, illustrating electricity consumption (KWh), voltage (U), current (I), and power (P) readings.

4.2 Pulse Output Indicator

The meter includes a pulse output indicator (1000imp/kwh) which flashes to indicate energy consumption. Each flash represents a specific amount of energy consumed, as per the meter's calibration.

5. Maintenance

The DDM15SC energy meter is designed for long-term, maintenance-free operation. However, periodic checks are recommended:

  • Keep the meter clean and free from dust and moisture.
  • Ensure all wiring connections remain tight and secure.
  • Do not attempt to open or repair the meter yourself. Refer to qualified service personnel if issues arise.

Note: This energy meter does not have a reset function for accumulated KWh readings.

6. Troubleshooting

If you encounter issues with your energy meter, consider the following:

  • No Display/No Power: Check the power supply to the meter and ensure all wiring connections are correct and secure. Verify that the circuit breaker is on.
  • Incorrect Readings: Double-check the wiring to ensure Live and Neutral lines are connected correctly. Ensure the meter's specifications match your electrical system.
  • Meter Not Functioning as Expected: If the above steps do not resolve the issue, consult a qualified electrician for further diagnosis and repair.

7. Specifications

The following table details the technical specifications of the DDM15SC Digital Energy Meter:

Image displaying key specifications of the DDM15SC model, including accuracy, voltage, current range, display type, wiring methods, power, installation, and operating temperature.

Figure 5: Visual summary of the DDM15SC energy meter's key specifications.

AttributeValue
Model NumberDDM15SC
Accuracy ClassFirst Grade
Reference Voltage220V/50Hz
Rated Voltage220V
Reference Current5-80A
Max Operating Current80A - 99A
Measuring Energy RangePower: 17000W
Display TypeDigital Only (LCD Digital Display)
PhaseSingle-phase
Power SupplyAC
Installation35mm DIN Rail
Pole Width17.5mm
Wiring MethodUp-out and Down-in / Up-in and Down-out
Operating TemperatureEnvironment Temperature: -20℃~+50℃
Dimensionsapprox. 7.8 * 3.7 * 6.6cm
Battery IncludedNo
DIY SuppliesElectrical
OriginMainland China
Dimensional drawing of the energy meter, showing approximate measurements of 7.8cm (length), 3.7cm (width), and 6.6cm (height).

Figure 6: Dimensions of the energy meter.

8. User Tips

  • Always ensure the meter is installed in a dry, well-ventilated area, away from direct sunlight or extreme temperatures, to ensure optimal performance and longevity.
  • For accurate readings, avoid installing the meter near strong magnetic fields or sources of electrical interference.
  • Periodically check the display for any unusual readings or error messages, although this model does not have advanced diagnostic features.

9. Warranty and Support

9.1 Warranty

This product comes with a 12-month manufacturer's limited warranty for defective items from the date of receipt. Accessories are covered by a 3-month warranty. The warranty does not cover items damaged or misused after receipt.

9.2 Technical Support

For technical assistance or inquiries not covered in this manual, please contact the seller or a qualified electrician. Do not attempt to disassemble or repair the device yourself, as this may void the warranty and pose safety risks.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.