SOMMER TX03-8-4

Contents

SOMMER 868MHz Remote Control

Model: TX03-8-4

Manufacturer: Huaruiyu

1. Introduction

This manual provides detailed instructions for the SOMMER 868MHz Remote Control, model TX03-8-4. This remote control is designed for use with compatible electric doors and gates operating on the 868MHz frequency. It features a rolling code technology for enhanced security and has a red LED indicator light.

SOMMER 868MHz Remote Control front view

Image: Front view of the SOMMER 868MHz Remote Control.

2. Specifications

Feature Specification
Frequency 868MHz
Channels 4
Wireless Communication RF (Radio Frequency)
Use Electric Door, Gate Control
Battery Type CR2032 (included)
Dimensions (Approx.) Length: 10 cm, Width: 10 cm, Height: 2 cm
Weight (Approx.) 0.06 kg
High-concerned chemical None

3. Compatibility

This remote control is compatible with the following SOMMER and APERTO models:

  • SOMMER 4020 TX03-868-4
  • SOMMER 4026 TX03-868-2
  • APERTO 4021
  • APERTO 4025
  • SOMMER 4011
  • SOMMER 4025
  • SOMMER 4031
  • SOMMER 4035
  • SOMMER 4025 BLUE
  • SOMMER 4026 TX03-868-2
  • SOMMER 4020 TX03-868-44011V000
  • 4020V000
  • 4025V000
  • 4026V000
  • 4031V000
  • 4035V002

Important Incompatibility Notes:

  • NOT compatible with SOMMER TX55 868.
  • NOT compatible with Sommer 868 MHz SOMloq2 (Pearl, Pearl Twin, Pearl Vibe hand-held transmitters).
Compatibility comparison for SOMMER remotes, showing 868MHz compatible and 434MHz not compatible.

Image: Visual comparison of compatible (868MHz) and incompatible (434MHz) SOMMER remote models.

4. Setup and Programming

There are generally two methods for programming your SOMMER remote control, depending on your receiver unit.

Method 1: Using the Learning Button on the Radio Receiver

Diagram showing programming steps for SOMMER remote control with receiver

Image: Diagram illustrating the programming process with the receiver's learning button.

  1. STEP 1: Locate the radio receiver on the circuit board. This button is often red or labeled with text like "code" or "radio".
  2. STEP 2: Press the learning button (A) on the radio receiver.
  3. STEP 3: Press the desired button on your new remote handset (B). The remote control will transmit the radio code to the receiver. The corresponding LED light on the receiver will go out according to which channel is selected.
  4. STEP 4: Repeat the procedure above to program additional remote control handsets if needed.

Method 2: Using the CODE Button on the Motor Controller Housing

  1. Open the motor controller housing of your electric door or gate system.
  2. Using a small screwdriver, press the button labeled "CODE" located at the far end of the head.
  3. The controller's LED light will illuminate.
  4. Pick up the SOMMER remote control, press and hold the first button.
  5. The LED on the controller will begin to flicker.
  6. Continue to hold the button on the remote control until the LED on the controller turns off.
  7. Release the button on the remote control. The programming is now complete.

5. Operating the Remote Control

Once programmed, operating the remote control is straightforward:

  • Press the corresponding button on the remote control that you programmed for your electric door or gate.
  • The red LED on the remote control will light up during transmission, indicating that a signal is being sent.
  • The door or gate should respond according to its programmed function (e.g., open, close, stop).

6. Maintenance and Battery Replacement

Battery Replacement

The remote control uses a CR2032 coin cell battery. If the remote's LED does not light up or its range decreases significantly, it's time to replace the battery.

Video: Demonstration of how to replace the CR2032 battery in the remote control.

  1. Pull out the concealed keypad section of the remote control to expose the battery compartment.
  2. Carefully remove the old CR2032 battery.
  3. Insert a new CR2032 battery, ensuring correct polarity (+/-). The positive (+) side typically faces upwards.
  4. Slide the keypad section back into place until it clicks securely.

Important: Only use CR2032 type batteries for replacement.

General Care

  • Keep the remote control dry and away from moisture.
  • Avoid exposing the remote to extreme temperatures or direct sunlight for prolonged periods.
  • Do not drop or subject the remote to strong impacts.
  • Clean the remote with a soft, dry cloth if necessary. Do not use harsh chemicals.

7. Troubleshooting

Problem Possible Cause Solution
Remote not working / Door not responding Battery is dead or low. Remote is not programmed correctly. Incompatibility with receiver. Replace battery (CR2032). Re-program the remote control following the steps in Section 4. Verify receiver compatibility (Section 3).
Remote LED does not light up Dead or incorrectly inserted battery. Replace the CR2032 battery, ensuring correct polarity.
Short operating range Low battery. Obstructions between remote and receiver. Receiver antenna is blocked or damaged. Replace battery. Ensure a clear line of sight. Check receiver antenna for damage or obstructions.
Difficulty with programming Incorrect procedure followed. Incompatible receiver. Carefully re-read and follow the programming steps in Section 4. Double-check compatibility with your system (Section 3).

8. User Tips

  • Verify Compatibility: Always confirm that this 868MHz remote is compatible with your existing garage door opener or gate system before attempting to program it. Refer to Section 3.
  • Battery Polarity: When replacing the battery, pay close attention to the correct positive (+) and negative (-) orientation to ensure proper function.
  • Test Range: After successful programming, test the remote's operating range from various distances and angles to ensure reliable performance.
  • Keep a Spare: Consider having a spare remote control or battery on hand for convenience.

9. Warranty and Support

For any issues not covered in this manual, or for warranty claims, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.