1. Overview
The AISET NG series is a reliable, cost-effective digital temperature controller, designed for precise temperature measurement and automatic control. It is suitable for industrial workshops, production lines, laboratories, and general automation equipment. Key features include simple operation, stable performance, high control accuracy, and strong adaptability. This controller is widely applied in various heating, cooling, and constant temperature control scenarios, fully complying with EU safety standards (EMC, LVD, WEEE directives).

2. Product Warning / Safety Information
Important Safety Warnings – Read carefully before use to avoid injury, equipment damage, or non-compliance with regulations.
- This product is for industrial use only, not for household use. Keep out of reach of children and untrained personnel to prevent accidents.
- WARNING: Always turn off the power supply before wiring, maintenance, disassembly, or cleaning to prevent electric shock and equipment damage.
- WARNING: Do not use the product beyond the rated parameters (voltage, temperature, load), which may cause fire, electric shock, or permanent product damage.
- WARNING: Avoid installing the controller in flammable, explosive, humid, dusty, or corrosive environments to eliminate potential safety hazards.
- WARNING: The controller must be grounded correctly in accordance with EU EMC and LVD directives; mandatory grounding is required for safe use and compliance.
- WARNING: Do not modify, disassemble, or repair the product without authorization; any unauthorized operation will void the warranty and may violate EU regulations.
- WARNING: In case of abnormal operation (smoke, peculiar odor, overheating, or display failure), turn off the power immediately and stop using it, then contact professional maintenance personnel.
- WARNING: Disposal of this product must comply with EU WEEE directives; do not discard it as household waste. Please hand it over to qualified recycling institutions.
3. Key Specifications
| Item | Parameter |
|---|---|
| Measurement Range | -50°C ~ 999°C |
| Control Accuracy | ±0.1°C |
| Input Signal | Thermocouple (K/J/T/E), RTD (PT100) |
| Output Mode | Relay output, SSR drive (optional) |
| Operating Voltage | AC 100~240V, 50/60Hz |
| Working Temperature | 0°C ~ 50°C |
| Protection Class | IP40 |
| Power (W) | 2 W |
| Battery Included | No |
| High-concerned chemical | None |
| Is Smart Device | No |
| Origin | Mainland China |

4. Setup and Initial Power On
Before powering on, ensure the controller is installed in a dry and ventilated place, away from high temperatures, humidity, strong electromagnetic interference, and flammable/explosive materials.
4.1 Power On
Connect the power supply according to the wiring diagram (ensure correct grounding to meet EU compliance). Then, turn on the power switch. The AISET NG controller will automatically display the current measured temperature after power-on, allowing quick monitoring of real-time temperature status.
5. Basic Operation
5.1 Set Target Temperature
- Press the "SET" key once. The display will flash, and you will enter the target temperature setting mode.
- Press the "▲" (up) or "▼" (down) key to adjust the target temperature to your required value. This operation provides intuitive and precise step adjustment.
- Press the "SET" key again to confirm and exit the setting mode. The NG series controller will then begin automatic temperature control.
5.2 Display Introduction
- Normal mode: The left display shows the current measured temperature (PV), and the right display shows the target temperature (SV), providing a clear and easy-to-read interface.
- Setting mode: The flashing display indicates the parameter currently being set. In simple operation, only the target temperature is adjustable, reducing complexity.
- Alarm mode: The alarm indicator (ALM) will light up when the temperature exceeds the set range (optional function), ensuring safe operation.

6. Wiring Instructions
Please turn off the power before wiring to avoid electric shock.
The basic wiring for the AISET NG series is as follows. Refer to the product label for specific details to ensure correct connection and EU compliance.
- Power Terminal (L/N): Connect to an AC 100~240V power supply. Ensure stable power input to avoid equipment malfunctions.
- Input Terminal (IN): Connect to a thermocouple or RTD temperature sensor. Ensure a tight connection for accurate signal transmission.
- Output Terminal (OUT): Connect to the load (e.g., heater, cooler). Match the load type with the controller's output mode.
- Ground Terminal (PE): Mandatory grounding is required (complies with EU safety regulations) to ensure safe use and prevent electrical hazards.
WARNING: Incorrect wiring (especially no grounding) may cause electric shock, fire, or product damage, violate EU regulations, and fail to meet AliExpress requirements. Always double-check the wiring before power-on.


7. Maintenance and Care
- Regularly check the wiring, sensor connection, and controller status to ensure stable operation and compliance.
- Clean the controller surface with a dry, soft cloth. Do not use corrosive cleaners to avoid damaging the product.
8. Troubleshooting
- Abnormal Operation: If you observe smoke, peculiar odor, overheating, or display failure, immediately turn off the power and stop using the device. Contact professional maintenance personnel. Do not attempt to repair it yourself to avoid safety risks.
- Wiring Issues: Double-check all wiring connections, especially grounding, if the device is not functioning as expected after installation. Incorrect wiring can lead to electric shock, fire, or product damage.
9. Warranty
The AISET NG series temperature controller provides a 12-month warranty from the date of delivery. This warranty covers defects caused by materials or workmanship under normal use and installation in accordance with this manual and EU regulations. The warranty does not cover damage resulting from improper operation, wrong wiring, unauthorized disassembly, non-compliance with EU regulations, or external factors.
10. Support and Further Information
This manual is a simplified EU compliance guide. For detailed operation steps, parameter settings, and advanced functions, please refer to the full-version manual.
A PDF version of the user manual is available for download: View User Manual (PDF)