HF-220 HF-220

Contents

Infrared Underfloor Heating Carbon Film Heater User Manual

Model: HF-220

Brand: Generic

Introduction

This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of your Infrared Underfloor Heating Carbon Film Heater. Please read this manual thoroughly before installation and retain it for future reference.

Rolled infrared heating film
Image: Rolled infrared heating film, showcasing its flexible design.

Safety Warnings

  • WARNING: Stay away from children and avoid misoperation.
  • WARNING: Do not disassemble or modify this product by yourself. Non-professional repairs may cause damage or safety accidents.
  • Do not use in damp or dusty environments.
  • Avoid severe impact or vibration on the product.
  • Ensure all electrical connections are made by a qualified professional to prevent electrical hazards.
  • Do not overlap heating films during installation. Maintain specified distances between films and from walls.

Specifications

Feature Specification
Model Number HF-220
Working Voltage 200~240V 50/60Hz
Rated Power 220W/m²
Max Surface Temperature 52°C degrees
Thickness 0.338mm
Width 50cm
Infrared Wave Length 8~15um
Material PEX
Certification NONE
Package Dimensions (L x W x H) 40cm x 10cm x 10cm
Package Weight 0.5 kg

Setup and Installation

Proper installation is crucial for the safe and efficient operation of your heating film. It is recommended that installation be performed by a qualified professional.

General Underfloor Installation Steps

  1. Clean and flatten the area where the heating film will be installed.
  2. If the area is wet, remove moisture completely and waterproof or place vinyl over the surface.
  3. Place insulation pad and fix the pads on the ground with OPP Tape. For improved heat efficiency, use thicker pads.
  4. Cut the edge of insulation pads according to each end of the surface.
  5. Leave about 5cm at the end of the pad and make space for the wires to go through. If the wires go between the pad, leave about 2~3 cm distance from each pad.
  6. Place heating film on the insulation pad.
  7. When placing films, keep 10~20 cm distance from the wall. Also, place at least 1cm distance from each film.
  8. When cutting the film, always follow the dot line marked with a scissors diagram.
Diagram showing general underfloor heating film installation steps
Image: Visual guide for general underfloor heating film installation, showing insulation and film placement.

Wiring the Heating Film

The heating film requires connection to a power source and a thermostat for temperature control. Ensure all connections are secure and insulated.

  1. Prepare the heating film for connection.
  2. Connect the power wires to the copper foil strips on the heating film.
  3. Install the floor temperature sensor.
  4. Connect the thermostat.
  5. Connect the entire installation to the main power supply.
Wiring diagram for heating film installation
Image: Detailed wiring diagram illustrating connections for the heating film, power, sensor, and thermostat.

Finishing Installation

  1. Cut special insulation tape into wide pieces and insulate the cut spots of copper foil on the heating film with the special insulation tape against moisture.
  2. Measure the resistances of all heating films installed by a resistance meter.
  3. Calculate the power consumption.
  4. Put the mold for electric wire close to the power outlet and arrange the wires into the mold.
  5. Fix the thermostat close to the power outlet.
  6. Before operating the thermostat, check the wiring of the heating film and if you have a current leakage tester, please check for leakage current.
  7. Start the thermostat and check the temperature of the heating film with a thermal measuring tool.
  8. In case of floor finishing is laminate floor, cover the heating film with non-woven fabric for protection.
  9. In case of floor finishing is linoleum or deco tile, you need to install a protection board on the heating film (5mm spacing is required when installing the protection board).
  10. Install the laminate floor, linoleum, or deco-tile as floor finishing.
Diagram showing finishing steps for heating film installation
Image: Finishing steps for heating film installation, including insulation, wiring, and initial testing.
Diagram showing floor finishing over heating film
Image: Instructions for covering the heating film with non-woven fabric or protection board before installing the final floor covering.

Important Installation Reminders:

  • When installing, do not overlap any film. Always maintain 1~3 cm distance between films.
  • Keep 10~20 cm distance between the wall and films.
  • Maximum film length for a single row: 50 cm model: 12~13 m; 80 cm model: 7~8 m; 100 cm model: 5~6 m. Do not exceed these limits.
Diagram showing layers of floor heating system
Image: Cross-section diagram illustrating the layers of a floor heating system, including heating film, insulation, and floor covering.

Operating Instructions

Once the heating film is correctly installed and connected to a thermostat, operation is straightforward:

  1. Refer to the operation manual of your specific thermostat for basic settings and programming.
  2. Select the corresponding functional mode (e.g., heating, eco, schedule) according to your heating requirements.
  3. Adjust the desired temperature using the thermostat controls. The system will automatically maintain the set temperature.

Infrared heating provides a comfortable warmth, often allowing for a lower ambient air temperature (3-4°C lower than traditional heating) while maintaining a similar feeling of warmth, which can lead to energy savings.

Diagram comparing radiator heating vs infrared film heating
Image: Comparison diagram showing how infrared heating film distributes warmth more evenly than traditional radiator heating.

Maintenance

The infrared heating film is designed for long-term, maintenance-free operation once installed correctly. However, consider the following general guidelines:

  • Ensure the environment remains dry and free from excessive dust.
  • Avoid placing heavy objects with sharp edges directly on the heated floor area that could damage the film or wiring underneath.
  • Regularly check the thermostat for proper functioning and calibration.
  • Do not attempt to access or repair the heating film once it is installed under the flooring. Contact a qualified technician if issues arise.

Troubleshooting

Problem Possible Cause Solution
Heating film not heating or insufficient heat. Loose or incorrect wiring connections; thermostat malfunction; insufficient insulation; film length exceeding maximum; power supply issue. Check all wiring connections (ensure proper clips/connectors are used); verify thermostat settings and functionality; ensure adequate insulation under the film; confirm film length is within specified limits; check power supply. Consult a professional if unsure.
Product received without connection accessories. Connection clips, tape, and thermostat are typically sold separately. Acquire necessary connection accessories (clips, insulation tape, thermostat) from a reputable supplier before installation.
Heating film heats up to 41°C instead of advertised 52°C max. Environmental factors (room temperature, external insulation); thermostat calibration; specific installation conditions. Ensure room is well-insulated; check thermostat calibration; verify installation matches recommended guidelines. While 41°C is sufficient for comfortable floor warming, if higher temperatures are critical, re-evaluate installation or consult a professional.
Can the film be installed under tiles? Tile adhesive contains moisture, which is incompatible with direct contact with the heating film. No, direct installation under tiles is not recommended. The film must be protected from moisture. Consider alternative heating methods for tiled floors or consult a specialist for suitable protective layers.
Can the film be cut to custom lengths? Yes, but only along designated cut lines. The film can be cut at intervals (e.g., 25cm, 50cm, 75cm) along the marked lines. Do not cut across the carbon heating elements or copper strips.

User Tips

  • Many users report quick installation and good quality, with the film being strong and having a thick layer.
  • The heating film is effective for underfloor warming, providing super heating as advertised.
  • Always ensure you acquire all necessary connection accessories (such as clips, insulation tape, and a thermostat) as they are typically not included with the heating film itself.
  • For optimal performance, pay close attention to the maximum film length per row and maintain proper spacing during installation.
  • The temperature can be regulated using a compatible thermostat, allowing for adjustable warmth.
  • The film can be placed under textile carpets or wooden floorboards, provided proper insulation and protective layers are used.

Warranty and Support

For any product-related inquiries, technical support, or warranty claims, please contact the seller or manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.