Dooya DC8811

Contents

Dooya DC8811 433MHz Solar Wireless Wind Sun Rain Sensor Instruction Manual

Model: DC8811

Introduction

The Dooya DC8811 is a solar-powered wireless wind, sun, and rain sensor designed for automated control of motorized awnings and shutters. It integrates solar power and battery, eliminating the need for an external AC power supply. This sensor detects environmental conditions and transmits signals via radio frequency to control your motorized systems, enhancing comfort and protection.

This manual provides essential information for the proper installation, operation, and maintenance of your DC8811 sensor.

Product Features

  • Integrated solar/battery power, no AC power supply required.
  • Detects wind, sun, and rain conditions.
  • Wireless control for motorized awnings and shutters.
  • Radio frequency: 433.05 MHz-434.79MHz (Bi-directional compatible: DD118H).
  • Range of validity: Outdoor > 100 meters, Indoor > 40 meters.
  • Compatible with Dooya DC90, DC92, DC1600, and other remotes.

Package Contents

Please check the package for the following items:

  • Dooya DC8811 Wind-Sun-Rain Sensor
  • Mounting accessories (screws, etc.)
  • Instruction Manual (this document)
Dooya DC8811 Wind-Sun-Rain Sensor with labeled buttons
Figure 1: Dooya DC8811 Wind-Sun-Rain Sensor with Menu, Setting, Reset, and Up buttons labeled.
Dimensions of Dooya DC8811 sensor: 12cm width, 27cm height
Figure 2: Dimensions of the DC8811 sensor, approximately 12cm wide and 27cm high.
Back view of Dooya DC8811 sensor showing 3.7V and 433MHz specifications
Figure 3: Back view of the DC8811 sensor, indicating 3.7V power and 433MHz frequency.

Setup and Installation

The DC8811 sensor is designed for self-contained installation, typically mounted using screws.

Initial Power On:

  1. Press the small white button on the sensor once to power it on.
  2. The screen will display "001".

Setting Wind, Sun, and Rain Levels:

After powering on, you can set the sensitivity levels for wind, sun, and rain.

  1. Rain Sensor Setting:
    • Press and hold the 'M' (Menu) button for two seconds. Do not release until the display changes.
    • Release the 'M' button. The display will show a flashing number for rain sensitivity.
    • Use the 'UP' button to increase the value or 'A' button to decrease the value. A common setting for rain is 'H' (High).
    • Once set, short press the 'M' button to move to the next setting.
  2. Sun Sensor Setting:
    • After setting rain, the display will show a flashing number for sun sensitivity.
    • Use the 'UP' button to increase or 'A' button to decrease the value. A common setting for sun is '0' (Off) if you prefer manual control or a specific light level.
    • Once set, short press the 'M' button to move to the next setting.
  3. Wind Sensor Setting:
    • After setting sun, the display will show a flashing number for wind sensitivity.
    • Use the 'UP' button to increase or 'A' button to decrease the value. You can freely set this value based on your preference for wind speed.
    • Once all three values (rain, sun, wind) are set, short press 'M' again to save and exit the setting mode.

Pairing with Remote Control (e.g., Dooya DC90, DC1600):

To connect the sensor to your motorized awning/shutter system, you need to pair it with your remote control.

  1. On your remote control (e.g., DC90, DC1600), locate the 'P2' button (often under a flap).
  2. Press the 'P2' button on the remote control twice.
  3. Immediately after, press the 'P2' button on the DC8811 sensor.
  4. The awning/shutter should make a slight movement (forward and backward) to confirm successful pairing.
Video 1: Demonstrates the initial power-on and setting of wind, sun, and rain sensitivity levels on the DC8811 sensor.

Operating Instructions

Once installed and configured, the DC8811 sensor operates automatically based on the set environmental thresholds.

  • Wind Detection: If wind speed exceeds the set threshold, the sensor will signal the motorized awning/shutter to retract to prevent damage.
  • Sun Detection: If sunlight intensity exceeds the set threshold (and sun mode is active), the sensor can signal the awning/shutter to extend for shade.
  • Rain Detection: If rain is detected (and rain mode is active), the sensor will signal the awning/shutter to retract to protect the fabric.

The sensor continuously monitors these conditions and sends commands to the paired receiver/motor via radio frequency.

Maintenance

To ensure optimal performance and longevity of your Dooya DC8811 sensor, follow these maintenance guidelines:

  • Cleaning: Periodically clean the sensor's exterior, especially the wind cups and the solar panel, to remove dust, dirt, and debris. Use a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Battery Check: As it is solar-powered with battery backup, ensure the solar panel receives adequate sunlight. If the sensor's performance seems erratic, check if the battery is charging properly.
  • Physical Inspection: Regularly inspect the sensor for any physical damage, loose components, or obstructions to the wind cups or rain sensor area.
  • Firmware Updates: Check the manufacturer's website or contact support for any available firmware updates.

Troubleshooting

Problem Possible Cause Solution
Awning/shutter retracts instead of extends (or vice-versa) when a condition is met. Incorrect programming or reversed logic during setup. Re-program the sensor and remote, ensuring the desired action (retract/extend) is correctly associated with the environmental condition. Consult your awning/shutter motor's manual for specific remote programming steps.
Sensor does not respond to environmental changes. Low battery, sensor not powered on, out of range, or incorrect sensitivity settings. Ensure the sensor is powered on (check display for "001"). Verify it's receiving sunlight for charging. Check the range between the sensor and the receiver. Re-check and adjust sensitivity settings for wind, sun, and rain as described in the "Setup and Installation" section.
Sensor not pairing with remote. Incorrect pairing procedure or incompatible remote. Follow the pairing steps precisely (press P2 on remote twice, then P2 on sensor). Ensure your remote control model is compatible with the DC8811 sensor (e.g., Dooya DC90, DC92, DC1600).

Specifications

Feature Detail
Model DC8811
Type Wind-Sun-Rain Sensor for Shutters/Awnings
Power Source Solar with integrated battery (3.7V)
Radio Frequency 433.05 MHz - 434.79 MHz
Compatibility Dooya DC90, DC92, DC1600 remotes (Bi-directional compatible: DD118H)
Range of Validity Outdoor > 100 meters, Indoor > 40 meters
Dimensions (L x W x H) 290mm x 130mm x 11mm (approx. 27cm x 12cm as per image)
Installation Method Self-contained (screw mounting)
Origin Mainland China

User Tips

  • Sun Sensor Setting for Dusk: If you want the awning to retract automatically at dusk, ensure the sun sensor is configured to detect low light levels. Some users find setting the sun level to '0' (or a very low value) effective for specific automation scenarios.
  • Programming Remote: When programming the sensor with a remote, remember the precise sequence: press the 'P2' button on the remote control twice, then immediately press the 'P2' button on the sensor. The awning's brief movement (forward and backward) confirms successful pairing.
  • Vibration Sensor: For enhanced protection against sudden impacts or strong vibrations not solely related to wind, a separate vibration sensor can be purchased and integrated into your system.
Separate vibration sensor for awning protection
Figure 4: An example of a separate vibration sensor that can be used with the system for enhanced protection.

Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or refer to the official Dooya website. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.