Introduction
This manual provides detailed instructions for assembling, operating, and maintaining your diymore D2-1 DIY Kit Intelligent Tracking Line Smart Car. This kit is designed to introduce users to fundamental electronic and mechanical principles through hands-on construction of a line-following robot.
The D2-1 Smart Car utilizes LM393 comparators and photosensitive resistors for line detection and DC motors with gear reduction for movement. It's an excellent educational tool for understanding concepts such as photocells, voltage comparators, motor drive circuits, and opto-electronic circuits.
Package Contents
The D2-1 DIY Kit includes the following components:
- 1PC x D2-1 DIY Kit Intelligent Tracking The Car Kit (unassembled parts)
- Printed Circuit Board (PCB)
- DC Motors with Gear Reduction
- Wheels and Tires
- Battery Holder (for 2 AA batteries, batteries not included)
- Photosensitive Resistors
- LEDs (Light Emitting Diodes)
- LM393 Comparator Integrated Circuit
- Resistors, Capacitors, Transistors, and other small electronic components
- Screws, nuts, and other mechanical fasteners
- Double-sided adhesive tape

Figure 1: Overview of the D2-1 DIY Kit components and an example of the assembled robot.

Figure 2: All components included in the D2-1 DIY Kit.
Assembly Instructions
Follow these steps carefully for successful assembly. It is recommended to have basic soldering tools and a multimeter.
Step 1: Circuit Part Welding
The welding of the circuit part is relatively straightforward. Follow the element height from low to high for the welding sequence. Begin with the 8 resistance components. Use a multimeter to confirm the proper resistance values before welding. Pay close attention to the polarity of components such as transistors, green LEDs (long pin is positive), and electrolytic capacitors (negative side indicated by PCB screen printing shadow). Avoid excessively long or poor welds. D4, D5, R13, and R14 can be temporarily left unwelded. Insert the integrated circuit chip after preliminary checks. After completing all welding, carefully inspect the circuit to prevent any errors.

Figure 3: Detailed view of the PCB with soldered components.

Figure 4: Top view of the PCB with component markings.
Step 2: Mechanical Assembly
- Insert the universal wheel screw into the designated PCB hole and secure it with the universal wheel nut and the universal wheel itself.
- Attach the battery box to the PCB using the double-sided adhesive tape. Ensure the lead wire passes through the reserved hole on the PCB. Connect the red wire to the 3V positive power supply and the yellow wire to the ground.
- Assemble the wheels: Each wheel consists of three pieces of black acrylic round tablets. Remove any protective film before assembly. The inner hole of the wheel center should be circular. The middle round plate has a smaller diameter. The lateral wheel piece center hole (Shiyuan) is fixed with two screw nuts.
- Fix the black self-tapping screws onto the rotating shaft of the engine (motor).
- Finally, slide the silicone rubber tire sleeve onto the wheel.
- Connect the motor lead wires to the PCB. Ensure sufficient clearance between the wheels and the PCB edge. Solder the motor leads to the PCB. Note: If the motor rotation direction is incorrect during testing, you can easily change the lead wire order.

Figure 5: Motors and battery holder attached to the PCB.
Step 3: Opto-electronic Circuits Installation
Install the photosensitive resistors and light-emitting diodes (LEDs) with careful attention to polarity. They should be installed in reverse on the PCB, with a ground distance of approximately 5mm. The distance between the light-sensitive resistor and the LED should also be about 5mm. After installation, perform an electrical test.

Figure 6: Underside of the PCB, showing soldering points.
Operating Instructions
Vehicle Debugging
Once assembly is complete, insert 2 AA batteries into the battery box. Flip the power switch to the "on" position. The car should begin driving. If the car travels backward, you may need to exchange the connection of the two motors simultaneously. If the car travels backward on only one side, exchange the wiring of the motor on that specific side.
The car is designed to follow a line. If you hold your hand over the left photosensitive resistor, the car should turn right. If you hold your hand over the right photosensitive resistor, the car should turn left. This demonstrates its line-tracking capability.

Figure 7: Assembled D2-1 Smart Car.
Maintenance
- Cleaning: Keep the photosensitive resistors and LEDs clean to ensure accurate line detection. Dust or debris can interfere with their function.
- Battery Replacement: Replace AA batteries when the car's performance degrades or it stops moving.
- Inspections: Periodically check all soldered connections for integrity. Ensure all mechanical fasteners (screws, nuts) are tight.
- Storage: Store the kit in a dry, cool place away from direct sunlight and moisture when not in use.
Troubleshooting
- Car moves backward: If the car drives in reverse, exchange the connection of the two motor wires simultaneously.
- Car turns incorrectly or doesn't follow line:
- Check the wiring of the photosensitive resistors and LEDs for correct polarity and secure connections.
- Ensure the distance between the photosensitive resistors and LEDs, and from the ground, is approximately 5mm.
- Verify that the motor leads are soldered correctly. If one side moves backward, exchange the wiring for that specific motor.
- Car does not move:
- Check if batteries are inserted correctly and have sufficient charge.
- Ensure the power switch is in the "on" position.
- Inspect all soldered joints for cold joints or short circuits.
- Verify that the LM393 IC is correctly inserted into its socket (if applicable) and oriented properly.
- Intermittent operation: Check for loose wires or components. Ensure all connections are firm.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | diymore |
| Type | Module (DIY Kit) |
| Model | D2-1 |
| Origin | Mainland China |
| Condition | New |
| Main Control IC | LM393 Dual Voltage Comparator |
| Detection Method | Photosensitive Resistance (Reflectance Optical Switch) |
| Motors | DC Motors with Gear Reduction |
| Power Source | 2 x AA Batteries (not included) |
| Approx. Package Weight | 0.118 kg |
| Approx. Package Dimensions (L x W x H) | 1 cm x 1 cm x 1 cm (Note: These are placeholder package dimensions; actual product dimensions will vary upon assembly.) |
User Tips
- The kit includes two motors with strong gearboxes and an integrated circuit for motor control, providing a robust foundation for line-following functionality.
- Take your time during the soldering process, especially with component polarity, to avoid rework.
- Ensure the photosensitive sensors are positioned correctly and at the optimal height for reliable line detection.
Frequently Asked Questions (FAQ)
- Q: What is the intended use of this item?
- A: The product is designed to serve the purpose of a line-following robot, ideal for educational and hobbyist projects.
Warranty and Support
For any issues or questions regarding the diymore D2-1 DIY Kit, please refer to the seller's support channels. As this is a DIY kit, successful operation depends on correct assembly. Ensure all steps are followed carefully.
A user manual in PDF format may be available for additional reference. Please check the product page or contact the seller for access to the PDF manual: User manual (PDF)