HM Digital AP-2

Contents

HM Digital AquaPro AP-2 Water Quality Tester User Manual

EC and Temperature Measurement with Automatic Calibration and Datahold

1. Product Overview

The HM Digital AquaPro AP-2 is a handheld water quality tester designed to accurately measure electrical conductivity (EC) and temperature in aquatic environments. This device features automatic temperature compensation (ATC), digital calibration, and a data-hold function, making it suitable for various applications from home use to laboratory testing. This manual provides detailed instructions for its use, maintenance, and troubleshooting.

Front view of the HM Digital AquaPro AP-2 water quality tester
Figure 1: HM Digital AquaPro AP-2 Water Quality Tester

2. Components and Controls

Familiarize yourself with the main components and controls of your AquaPro AP-2 tester:

Diagram showing the components and dimensions of the AquaPro AP-2 tester
Figure 2: AquaPro AP-2 Component Diagram
  • Display Screen: Large LCD screen showing EC (µS) and temperature (°C/°F) readings.
  • Power Button: Turns the device on and off.
  • Mode Button (▲): Used for calibration, temperature scale selection, and navigating menus.
  • HOLD Button (▼): Freezes the current reading on the display. Also used for navigating menus.
  • Battery Case: Houses the CR2032 button cell battery.
  • Electrode (Metal Pins): The sensor for measuring electrical conductivity.
  • Thermistor: Measures water temperature.
  • Protective Cap: Covers and protects the electrodes and thermistor when not in use.

3. Setup

3.1 Preparatory Work

  1. Inspection: Before first use, inspect the tester for any visible damage.
  2. Battery Installation: The AquaPro AP-2 requires one 3V button cell (CR2032) battery. Open the battery case (refer to Figure 2) and insert the battery, ensuring correct polarity. Note: Batteries are not included due to air freight restrictions.
  3. Power Source: Ensure the power supply is stable if connecting to an external power source (though typically battery-operated).
  4. Calibration Check: The AquaPro is factory calibrated with a 700 µS solution. It is recommended to check calibration periodically.

4. Operating Instructions

4.1 Testing Procedure

  1. Power On: Press the POWER button to switch on the instrument. The system will initialize and display the main interface.
  2. Select Parameter (if applicable): For this 2-in-1 model, EC and temperature are measured simultaneously. To switch between °C and °F for temperature, press and hold the MODE button.
  3. Immerse Sensor: Remove the protective cap. Immerse the sensor section (electrodes and thermistor) of the water quality monitor into the water sample to be tested, ensuring full contact between the sensor and the water. Do not immerse above the indicated water level.
  4. Read Results: Wait a few seconds for the reading to stabilize. The instrument will automatically measure and display the EC and temperature results on the LCD screen.
  5. Data Hold: To freeze the current reading on the display, press the HOLD button. Press it again to release the hold function.
  6. Power Off: The device has an auto-off function to conserve battery. Alternatively, press the POWER button to manually turn it off.
AquaPro AP-2 water quality tester immersed in a glass of water, displaying an EC reading and temperature
Figure 3: Taking a measurement with the AquaPro AP-2
Close-up images of the AquaPro AP-2 display showing different readings for EC and temperature, including the data-hold function indicator
Figure 4: Example display readings (EC, Temperature, Hold function)

4.2 Digital Calibration

The AquaPro AP-2 features digital calibration via push buttons, eliminating the need for a screwdriver. For detailed calibration steps, refer to the full user manual PDF.

4.3 Understanding Water Conductivity

Electrical conductivity (EC) is a measure of the total amount of dissolved solids, which reflects the conductivity of total ions in the water. This indicates the quality of the reaction water.

Water conductivity chart illustrating EC values for different water types
Figure 5: Water Conductivity Chart

Conversion: To convert µS (micro-Siemens) to mS (milli-Siemens), divide by 1000 (e.g., 1000 µS = 1 mS).

4.4 Product Demonstration Video

Watch a brief demonstration of the HM Digital AquaPro AP-2 water quality tester.

5. Maintenance

5.1 Operating Environment

The water quality monitor is intended for indoor use only. Avoid exposure to direct sunlight or adverse weather conditions. Additionally, refrain from using it near pollution sources to prevent interference with test results.

5.2 Sensor Maintenance

Maintaining the cleanliness of the sensor assembly is crucial for ensuring accurate measurements. After each use, clean the sensor using appropriate methods (e.g., rinsing with distilled water) to ensure its surface remains free of contaminants. Always replace the protective cap after use.

5.3 Power Management

Regularly check battery levels. Should a low-battery warning occur during operation, promptly replace the CR2032 battery. Remove batteries during prolonged periods of non-use to prevent leakage and damage to the instrument.

5.4 Impact Prevention

As a precision instrument, the water quality monitor must be protected from impacts, drops, or compression during use to prevent damage.

6. Troubleshooting

Below are common faults and their suggested solutions:

ProblemSuggested Solution
Display shows garbled characters or no displayCheck the instrument's battery level and attempt to restart the device. Replace battery if low.
Inaccurate or unstable test resultsFirst, verify that the sensor is clean and functioning correctly. If necessary, recalibrate the device and ensure the measurement environment is stable.
Instrument fails to power onConfirm that the power supply is properly connected. If using batteries, ensure they are fully charged or replace them before attempting to power on again.

7. Specifications

ParameterValue
Model NumberAP-2
Display TypeDIGITAL
EC Range0-9999 µS (µS/cm)
Temperature Range0-80 °C; 32-176 °F
EC Resolution1 µS
Temperature Resolution0.1 °C/F
Accuracy+/- 2%
CalibrationDigital calibration by push button (factory calibrated with 700 µS solution)
Automatic Temperature Compensation (ATC)Yes
HousingWater-resistant
Auto-off FunctionYes
Data-hold FunctionYes
Low-battery IndicatorYes
Power Source1 x 3V button cell (model CR2032)
Dimensions15 x 2.8 x 1.3 cm (5.9 x 1.1 x 0.5 inches)
CertificationCE
PatentU.S. PATENT D602,384S (Magnetic body patent pending)

8. User Tips

  • Regular Cleaning: Always clean the electrodes with distilled water after each use to maintain accuracy and prolong sensor life.
  • Battery Life: Keep spare CR2032 batteries on hand, as they are not included with the device. Remove batteries if storing the device for extended periods.
  • Calibration: While factory calibrated, recalibrate periodically or if you suspect inaccurate readings, especially for critical applications.
  • Handling: Treat the device as a precision instrument; avoid dropping or subjecting it to strong impacts.

9. Warranty and Support

For detailed warranty information and further support, please refer to the official documentation. A comprehensive user manual is available in PDF format:

View Full User Manual (PDF)

If you encounter any issues not covered in this manual or require further assistance, please contact customer support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.