Beitian BE-280, BE-357P

Contents

Beitian BE-280 / BE-357P UBX M10 GNSS Antenna Module User Manual

Ultra-low Power GNSS Receiver for Tracking and Navigation

1. Introduction

This manual provides detailed instructions for the Beitian BE-280 and BE-357P UBX M10 GNSS Antenna Modules. These modules are ultra-low power, high-performance GNSS receivers designed for various applications including RC airplanes, drones, and other tracking systems. Please read this manual thoroughly before installation and operation to ensure proper use and optimal performance.

Front and back view of the Beitian BE-280 GPS module

Figure 1: Front and back view of the Beitian BE-280 GPS module, showing components and antenna.

2. Safety Information

  • Handle the module with care to avoid damage to electronic components.
  • Ensure correct power supply voltage (DC 3.6V-5.5V) to prevent damage.
  • Avoid exposing the module to extreme temperatures outside the specified operating range (-40°C to +85°C).
  • Keep the module away from strong magnetic fields or sources of radio interference that could affect GNSS signal reception.
  • Do not attempt to disassemble or modify the module, as this will void the warranty and may cause damage.

3. Package Contents

Verify that all items are present in your package:

  • 1x Beitian BE-280 or BE-357P GNSS Module
  • 1x 6-pin connection cable (1.25mm connector)
  • 1x 3M adhesive pad
Beitian BE-280 GPS module with cable and adhesive pad

Figure 2: Beitian BE-280 GPS module with its 6-pin connection cable and a 3M adhesive pad.

4. Specifications

The following table details the technical specifications for the Beitian BE-280 GNSS module:

Datasheet table for Beitian BE-280 GNSS module

Figure 3: Datasheet table for the Beitian BE-280 GNSS module.

Beitian BE-280 GNSS Module Datasheet
ParameterDescription
ChipM10050
FrequencyGPS L1 C/A, QZSS L1 C/A/S, BDS B1I/B1C, Galileo E1B/C, SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN
Operating ModeGPS+BDS+GALILEO+SBAS+QZSS
Track Channels72 channel
Sensitivity (Acquisition)-160dBm
Sensitivity (Cold Start)-148dBm
Sensitivity (Hot Start)-160dBm
Horizontal Accuracy1.5m CEP 2D RMS, SBAS: Auxiliary (for Open Sky)
Speed Accuracy0.05m/s
Dynamic Heading Precision0.3 deg
Angle AccuracyRMS 30ns
1PPS Time Accuracy99% 60ns
Cold Start Time27s
Hot Start Time1s
Assisted Start Time1s
Baud Rate4800bps - 921600bps (default 38400bps)
Output LevelTTL level
Output ProtocolNMEA, UBX
NMEA SentencesRMC, VTG, GSA, GSV, GLL
Update Frequency0.2 Hz-10Hz (default 1Hz)
Second PulseConfigurable from 0.25 Hz to 10 MHz, default 1s period, 100ms high level
Max High50000m
Max Speed500m/s
Max Gravitational Acceleration<4g
VoltageDC 3.6V-5.5V (typical: 5.0V)
Current (Normal)50mA/5.0V
Size28mm x 28mm x 8.4mm
Weight11.8g
Package1.25mm 6pins connector
Operating Temperature-40°C ~ +85°C
Storage Temperature-40°C ~ +105°C
LEDBuilt-in TX LED (blue), flashes upon data output.
Dimensional drawing of the Beitian BE-280 GPS module

Figure 4: Dimensional drawing of the Beitian BE-280 GPS module, showing top, side, and bottom views with measurements in millimeters.

5. Setup and Connection

Follow these steps to connect your GNSS module:

  1. Identify Pins: Refer to Figure 1 for the pinout. The module typically has pins for VCC (Power), GND (Ground), TX (Transmit Data), RX (Receive Data), and PPS (Pulse Per Second). The 6-pin connector includes these and potentially an additional control pin.
  2. Connect Power: Connect the VCC pin to a stable DC 3.6V-5.5V power source (typical 5.0V) and the GND pin to your system's ground.
  3. Connect Data (UART): Connect the TX pin of the GNSS module to the RX pin of your microcontroller or flight controller. Connect the RX pin of the GNSS module to the TX pin of your microcontroller or flight controller.
  4. PPS Output (Optional): The PPS pin provides a 1Hz pulse for precise timing applications. Connect this to an interrupt-capable pin on your microcontroller if needed.
  5. Mounting: Use the provided 3M adhesive pad to securely mount the module in a location with a clear view of the sky, away from potential interference sources like motors, ESCs, or high-current wires.
  6. Initial Configuration: The module defaults to 38400bps baud rate and outputs NMEA/UBX protocol. Ensure your receiving device is configured to match these settings.

6. Operating Instructions

  1. Power On: Once correctly wired, apply power to the module. The blue TX LED will illuminate and begin flashing when data is being transmitted.
  2. Satellite Acquisition: Upon first power-up (cold start), the module will take approximately 27 seconds to acquire satellites and obtain a fix. Subsequent power-ups (hot start) will be much faster, around 1 second, if the module has retained recent satellite data.
  3. Data Output: The module will output GNSS data in NMEA or UBX format via the TX pin. This data can be read by a connected microcontroller or computer for navigation and tracking purposes.
  4. Monitoring: Use a serial monitor or dedicated GNSS software to view the incoming data and verify satellite lock and position accuracy.

7. Maintenance

  • Cleaning: Keep the module clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Storage: When not in use, store the module in a dry, cool environment within the specified storage temperature range (-40°C to +105°C).
  • Inspection: Periodically inspect the module and its connections for any signs of wear or damage.

8. Troubleshooting

No Data Output / TX LED not flashing:
  • Check power connections (VCC and GND) to ensure the module is receiving adequate power (3.6V-5.5V).
  • Verify that the TX pin of the module is correctly connected to the RX pin of your receiving device.
  • Confirm that the baud rate settings on your receiving device match the module's default (38400bps) or configured baud rate.
No Satellite Fix / Poor Accuracy:
  • Ensure the module has a clear, unobstructed view of the sky.
  • Move the module away from potential sources of electromagnetic interference (e.g., motors, power cables, other wireless modules).
  • Allow sufficient time for a cold start (up to 27 seconds) if the module has been off for an extended period or moved a significant distance.
  • Check for proper antenna connection if applicable (this module has an integrated antenna).
Module Not Responding:
  • Power cycle the module.
  • Recheck all wiring connections.
  • Ensure the power supply is stable and within the specified voltage range.

9. User Tips

  • For optimal performance, mount the module as far as possible from other electronics that generate electromagnetic interference.
  • Consider using a ground plane under the module if your application allows, as this can improve antenna performance.
  • If using with a flight controller, ensure the flight controller firmware supports the UBX or NMEA protocol and the correct baud rate.
  • Always double-check wiring before applying power to prevent damage to the module or connected devices.

10. Warranty and Support

For warranty information, technical support, or inquiries regarding your Beitian BE-280 or BE-357P GNSS module, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.