1. Introduction
This manual provides detailed instructions for the Beitian UBX M10050 series GNSS GPS modules, including models BE-180, BE-220, BE-280, and BE-880. These modules are designed for use in various applications such as fixed-wing FPV aircraft, RC airplanes, and other remote control toys requiring precise navigation and positioning. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.
2. Safety Information
- Always handle electronic components with care to prevent electrostatic discharge (ESD) damage.
- Ensure correct voltage and polarity when connecting the module to avoid damage. Refer to the specifications for voltage requirements.
- Do not expose the module to extreme temperatures, moisture, or corrosive environments.
- Keep the module away from strong magnetic fields, especially the BE-880 model which includes a compass.
- Professional installation is recommended for complex setups involving soldering or firmware configuration.
3. Package Contents
Depending on the specific model purchased, your package may include:
- Beitian GNSS GPS Module (BE-180, BE-220, BE-280, or BE-880)
- Wiring harness (4-pin for BE-220, 6-pin for BE-280/BE-880)
- 3M adhesive pad(s) for mounting



4. Specifications
The Beitian UBX M10050 series modules share many core specifications. Model-specific differences are noted below.
| Parameter | Value |
|---|---|
| Chip | M10050 |
| Frequency | GPS L1 C/A, QZSS L1 C/A/S, BDS B1I/B1C, Galileo E1B/C, SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN |
| Operating Mode | GPS+BDS+GALILEO+SBAS+QZSS |
| Track Sensitivity | -166dBm |
| Re-acquire Sensitivity | -160dBm |
| Cold Start Sensitivity | -148dBm |
| Hot Start Sensitivity | -160dBm |
| Horizontal Accuracy | 1.5m CEP 2D RMS SBAS Auxiliary (for Open Sky) |
| Speed Accuracy | 0.05m/s |
| Dynamic Heading Angle Accuracy | 0.3 deg |
| 1PPS Time Accuracy | RMS 30ns, 99% 60ns |
| Cold Start Time | 27s |
| Hot Start Time | 1s |
| Assisted Start Time | 1s |
| Baud Rate | 4800bps - 921600bps (default 38400bps) |
| Output Level | TTL level |
| Output Protocol | NMEA, UBX |
| NMEA Sentences | RMC, VTG, GSA, GSV, GLL |
| Update Frequency | 0.25Hz-18Hz, default 1Hz (Configurable from 0.25 Hz to 10 MHz, default period 1s, high level lasts 100ms) |
| Max High | 80,000m |
| Max Speed | <500m/s |
| Max Gravitational Acceleration | <4g |
| Voltage | DC 3.6V-5.5V (typical: 5.0V) |
| Operating Temperature | -40°C ~ +85°C |
| Storage Temperature | -40°C ~ +105°C |
| LED | Built-in LED, TX LED: blue (flashing on data output) |
| Model | Size (mm) | Weight (g) | Connector | Compass |
|---|---|---|---|---|
| BE-180 | 18 x 18 x 6.2 | Not specified (very light) | Soldering pads (no connector) | No |
| BE-220 | 22 x 20 x 6 | 5.1 | 1-5mm 4-pins | No |
| BE-280 | 28 x 28 x 8.4 | 11.8 | 1-5mm 6-pins | No |
| BE-880 | 28 x 28 x 8.4 (or 25.4 x 25.4 x 6.2, max 11.0 with antenna) | 12.0 | 1-5mm 6-pins | Yes |





5. Setup
5.1 Physical Installation
- Mounting: Use the provided 3M adhesive pads to securely attach the GPS module to a flat, stable surface on your aircraft or device. Ensure the module is oriented correctly, typically with the antenna facing upwards for optimal satellite reception.
- Placement: Position the module away from other electronic components that might generate electromagnetic interference (EMI), especially motors, ESCs, and video transmitters. For models with a compass (BE-880), this is crucial to prevent magnetic interference that can affect heading accuracy.
5.2 Wiring
Connect the GPS module to your flight controller or microcontroller using the provided wiring harness. The pinout is standard for most flight controllers.
- VCC: Connect to a stable 3.6V-5.5V power supply (typically 5V from the flight controller).
- GND: Connect to the ground of your system.
- TX (Transmit): Connect to the RX (Receive) pin of your flight controller's UART port.
- RX (Receive): Connect to the TX (Transmit) pin of your flight controller's UART port.
- PPS (Pulse Per Second): (Optional) Connect to a dedicated PPS input on your flight controller for precise timing synchronization.
- SDA/SCL (for BE-880 compass): Connect to the I2C SDA and SCL pins of your flight controller for compass functionality.
5.3 Initial Configuration
After physical installation and wiring, configure your flight controller software (e.g., Betaflight, iNav, ArduPilot) to recognize and utilize the GPS module.
- Enable GPS: In your flight controller's configurator, enable the GPS feature and select the correct UART port to which the module is connected.
- Baud Rate: Set the UART baud rate to the default of the GPS module, which is typically 38400bps. This can be adjusted if needed, but ensure it matches the module's setting.
- Protocol: Select the appropriate GPS protocol, usually UBLOX or NMEA, depending on your flight controller's capabilities and the module's default output.
- Compass (BE-880 only): If using the BE-880, enable the compass feature and select the I2C port. You may need to perform a compass calibration.
6. Operating Instructions
Once properly set up, the GPS module will automatically begin searching for satellites upon power-up. The blue TX LED will flash when data is being output.
- First Fix: The initial cold start may take up to 27 seconds to acquire a satellite fix. Subsequent hot starts will be much faster (around 1 second).
- Signal Acquisition: For best performance, operate the module in an open outdoor area with a clear view of the sky. Avoid operating indoors or near tall buildings that can obstruct satellite signals.
- Monitoring: Use your flight controller's OSD (On-Screen Display) or configurator software to monitor GPS status, including satellite count, HDOP (Horizontal Dilution of Precision), and 3D fix status.
7. Maintenance
- Cleaning: Keep the module clean and free from dust and debris. Use a soft, dry cloth for cleaning.
- Inspection: Periodically inspect the wiring and connections for any signs of wear or damage.
- Firmware Updates: Check the manufacturer's website for any available firmware updates for your specific module model. Follow update instructions carefully.
8. Troubleshooting
- No GPS Fix:
- Ensure the module has a clear view of the sky.
- Verify wiring connections (VCC, GND, TX, RX) are correct.
- Check the baud rate and GPS protocol settings in your flight controller software.
- Allow sufficient time for a cold start (up to 27 seconds).
- Inaccurate Position/Heading:
- Relocate the module away from sources of EMI (motors, ESCs, VTX).
- For BE-880 (with compass), ensure it's calibrated and not affected by magnetic interference.
- Module Not Detected by Flight Controller:
- Confirm the correct UART port is selected and enabled in the flight controller software.
- Check for continuity in the wiring harness.
- Ensure the flight controller firmware supports the GPS module (e.g., iNav firmware for Omnibus F4 V3).
- Compatibility Issues:
- While these modules are generally compatible with many flight controllers, specific drone models (e.g., E88 Pro, Visuo XS816) may require additional hardware (like OSD return) or specific firmware configurations (e.g., Betaflight settings) that might not be directly supported by the module alone. Consult your drone's manual or community forums for compatibility.
9. User Tips
- The BE-880 model is the only one in this series that includes a compass. If your application requires a compass, ensure you select the BE-880. The BE-220 and BE-280 models are GPS-only.
- The BE-220 is noted as the smallest module among the BE-180, BE-220, BE-280, and BE-880, making it suitable for space-constrained builds.
- For flight controllers like the Omnibus F4 V3 running iNav firmware, these modules should be compatible if the flight controller has available UART and/or I2C ports for connection.
- When integrating with drones that have proprietary systems, check if an OSD return is required and if the flight controller can be configured via software like Betaflight for GPS and compass functionality.
10. Warranty and Support
For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty-related inquiries. The manufacturer strives to provide high-quality products and support.