heimerdinger LB169

Contents

Heimerdinger LB169 18V Cordless Rotary Hammer Drill

User Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Heimerdinger LB169 18V Brushless Cordless Rotary Hammer Drill. Please read this manual thoroughly before using the tool and keep it for future reference.

Heimerdinger LB169 18V Cordless Rotary Hammer Drill
Heimerdinger LB169 18V Cordless Rotary Hammer Drill

2. General Safety Instructions

Always follow basic safety precautions to reduce the risk of fire, electric shock, and personal injury. Keep this manual and all safety warnings for future reference.

2.1 Work Area Safety

  • Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2.2 Electrical Safety

  • Power tool plugs must match the outlet. Never modify the plug in any way.
  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

2.3 Personal Safety

  • Always wear eye protection. Use safety glasses, goggles, or a face shield.
  • Wear hearing protection when operating noisy tools.
  • Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts.
  • Stay alert, watch what you are doing, and use common sense when operating a power tool.

2.4 Power Tool Use and Care

  • Do not force the power tool. Use the correct power tool for your application.
  • Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
  • Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation.

2.5 Battery Tool Use and Care

  • Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
  • Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
  • When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

3. Package Contents

The contents of your package may vary depending on the option purchased. Please verify your package against the list below:

Option 1: Basic Kit (1x 4.0Ah Battery)

  • 1 x Cordless Brushless Hammer Drill
  • 1 x Charger
  • 1 x 18V 4.0Ah Lithium Rechargeable Battery
  • 1 x Instruction Manual
  • 1 x Auxiliary Handle

Note: Blow Mold Case not included.

Package contents for Option 1: Drill, 1x 4.0Ah battery, charger, handle
Option 1 Package Contents

Option 2: Basic Kit (1x 6.0Ah Battery)

  • 1 x Cordless Brushless Hammer Drill
  • 1 x Charger
  • 1 x 18V 6.0Ah Lithium Rechargeable Battery
  • 1 x Instruction Manual
  • 1 x Auxiliary Handle

Note: Blow Mold Case not included.

Package contents for Option 2: Drill, 1x 6.0Ah battery, charger, handle
Option 2 Package Contents

Option 3: Dual Battery Kit (2x 4.0Ah Batteries)

  • 1 x Cordless Brushless Hammer Drill
  • 1 x Charger
  • 2 x 18V 4.0Ah Lithium Rechargeable Batteries
  • 1 x Instruction Manual
  • 1 x Auxiliary Handle

Note: Blow Mold Case not included.

Package contents for Option 3: Drill, 2x 4.0Ah batteries, charger, handle
Option 3 Package Contents

Option 4: Dual Battery Kit (2x 6.0Ah Batteries)

  • 1 x Cordless Brushless Hammer Drill
  • 1 x Charger
  • 2 x 18V 6.0Ah Lithium Rechargeable Batteries
  • 1 x Instruction Manual
  • 1 x Auxiliary Handle

Note: Blow Mold Case not included.

Package contents for Option 4: Drill, 2x 6.0Ah batteries, charger, handle
Option 4 Package Contents

Option 5: Dual Battery Kit with Case (2x 4.0Ah Batteries)

  • 1 x Cordless Brushless Hammer Drill
  • 1 x Charger
  • 2 x 18V 4.0Ah Lithium Rechargeable Batteries
  • 1 x Instruction Manual
  • 1 x Auxiliary Handle
  • 1 x Blow Mold Case
Package contents for Option 5: Drill, 2x 4.0Ah batteries, charger, handle, and blow mold case
Option 5 Package Contents

Option 6: Dual Battery Kit with Case (2x 6.0Ah Batteries)

  • 1 x Cordless Brushless Hammer Drill
  • 1 x Charger
  • 2 x 18V 6.0Ah Lithium Rechargeable Batteries
  • 1 x Instruction Manual
  • 1 x Auxiliary Handle
  • 1 x Blow Mold Case
Package contents for Option 6: Drill, 2x 6.0Ah batteries, charger, handle, and blow mold case
Option 6 Package Contents

4. Product Overview

Familiarize yourself with the components of your rotary hammer drill before operation.

Diagram of Heimerdinger LB169 rotary hammer drill with labeled parts: quick chuck, four function switch, cooling hole, forward/reverse switch, on/off trigger, handle, battery, battery capacity display.
Heimerdinger LB169 Component Diagram
  1. Quick Chuck
  2. Four Function Switch
  3. Cooling Hole
  4. Forward/Reverse Switch
  5. On/Off Trigger
  6. Auxiliary Handle
  7. Battery
  8. Battery Capacity Display

5. Setup

5.1 Charging the Battery

  1. Ensure the charger is connected to a suitable power outlet.
  2. Insert the battery pack into the charger. The charger indicator light will show the charging status.
  3. Once fully charged, remove the battery from the charger.

5.2 Installing/Removing the Battery

  1. To install: Align the battery pack with the base of the tool and slide it in until it clicks securely into place.
  2. To remove: Press the battery release button (if present) and slide the battery pack out.

5.3 Attaching the Auxiliary Handle and Depth Rod

  1. Loosen the auxiliary handle clamp.
  2. Slide the handle onto the front of the tool body.
  3. Insert the depth rod into the hole on the handle.
  4. Adjust the handle to a comfortable position and tighten the clamp securely. Adjust the depth rod to the desired drilling depth.

5.4 Installing SDS Plus Drill Bits/Chisels

  1. Clean the shank of the SDS Plus accessory.
  2. Pull back the quick chuck (tool holder) sleeve.
  3. Insert the SDS Plus accessory into the chuck, rotating it slightly until it slides fully into place.
  4. Release the sleeve. Pull on the accessory to ensure it is securely locked. The SDS Plus system allows for slight axial movement of the bit, which is normal.
  5. To remove: Pull back the quick chuck sleeve and pull out the accessory.

6. Operating Instructions

6.1 Mode Selection

The tool features a four-function switch to select the desired operating mode:

Diagram showing the four function switch settings: Hammer Mode, Calibration Mode, Flat Drill Mode, Shovel Mode.
Four Function Switch Settings
  • Hammer Mode (Rotary Hammer): For drilling in concrete, masonry, and stone with hammer action.
  • Flat Drill Mode (Drill Only): For drilling in wood, metal, and plastics without hammer action.
  • Shovel Mode (Chiseling): For chiseling, chipping, and demolition work.
  • Calibration Mode (Chisel Position Adjustment): Allows rotation of the chisel to the desired working angle without hammer action.

To change modes, rotate the four-function switch to the desired icon. Ensure the tool is off before changing modes.

6.2 Forward/Reverse Switch

The forward/reverse switch is located above the on/off trigger. Push it left for forward rotation (drilling/hammering) and right for reverse rotation (e.g., removing stuck drill bits). Ensure the tool has come to a complete stop before changing direction.

6.3 On/Off Trigger

Press the on/off trigger to start the tool. The speed is variable depending on how far the trigger is pressed. Release the trigger to stop the tool.

6.4 Operation Tips

  • Always hold the tool firmly with both hands, using the auxiliary handle.
  • Apply steady, even pressure. Do not force the tool.
  • For drilling, start with a slow speed to create a pilot hole, then increase speed as needed.
  • When chiseling, allow the tool to do the work; do not lean heavily on it.
  • Monitor the battery capacity display and recharge as needed to avoid interruptions.

7. Maintenance

7.1 Cleaning

  • Regularly clean the ventilation slots on the tool to prevent overheating.
  • Wipe down the tool body with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
  • Keep the chuck free of dust and debris.

7.2 Lubrication

It is recommended to periodically check and lubricate the gearbox to ensure optimal performance and extend the tool's lifespan. Consult a qualified service technician if you are unsure how to perform this maintenance.

7.3 Battery Care and Storage

  • Store batteries in a cool, dry place away from direct sunlight and extreme temperatures.
  • Do not store batteries in a discharged state for extended periods. Recharge them periodically.
  • Avoid dropping or damaging battery packs.

8. Troubleshooting

Problem Possible Cause Solution
Tool does not start Battery not installed correctly or discharged. Ensure battery is fully charged and properly seated.
Loss of power during operation Battery low or tool overloaded. Recharge battery. Reduce pressure on the tool.
Excessive vibration or noise Loose accessory, worn parts, or lack of lubrication. Check accessory for secure fit. Inspect tool for damage. Consider gearbox lubrication.
Drill bit stuck Over-drilling or incorrect technique. Switch to reverse rotation to free the bit.

9. Specifications

Feature Specification
Brand Name Heimerdinger
Model Number LB169
Hammer Type Rotary Hammer
Power Source Battery (18V Lithium-ion)
Rated Voltage 18V
Rated Input Power 18V 4.0Ah battery pack (standard, other capacities available)
Wattage 800W-999W
No-Load Speed 1200rpm
Frequency 0-4500ipm (Impacts Per Minute)
Impact Energy 3.2J
Max. Drilling Diameter 26MM
Interface SDS Plus
Weight (only body) 2.65kg
Dimensions 33cm x 23cm x 24cm
Certification CE, RoHS, FCC, MSDS
Origin Mainland China

9.1 Certifications

The Heimerdinger LB169 rotary hammer drill is certified to meet various international standards:

CE Certificate for Heimerdinger Cordless Brushless Wrench
CE Certificate
RoHS Certificate for Heimerdinger Cordless Brushless Wrench
RoHS Certificate
FCC Certificate for Heimerdinger Cordless Brushless Wrench
FCC Certificate
MSDS Report for Power Tool Battery LB5C
MSDS Report (Battery)

10. User Tips

  • For extended use or lighter tasks, consider using 4.0Ah batteries. They are lighter and can provide sufficient power for a full day's work (e.g., drilling 6mm holes). Larger capacity batteries (e.g., 9.0Ah) can add significant weight, which might cause fatigue during prolonged use.
  • Ensure the gearbox is adequately lubricated. Some users recommend checking and lubricating it upon initial use to ensure long-term reliability.
  • This tool is designed for SDS Plus accessories. SDS Max accessories are not compatible. Standard round drills require an appropriate adapter (not included).
  • While some users report compatibility with Makita 18V batteries, this is not officially guaranteed and performance may vary. It is recommended to use original Heimerdinger batteries for optimal performance and safety.
  • When drilling concrete, a 4.0Ah battery can drill multiple 11cm thick holes. Battery life will vary based on material, drill bit size, and application.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.