1. Introduction
This manual provides detailed instructions for the safe and effective use of the LD06AJSA/B DC 2.8V-6V LED Driver Module. This module is designed to provide a constant current output for driving 1 to 16 series/parallel connected LEDs, with current regulation capabilities via an adjustable resistor or PWM signal control. It features chip temperature regulation and over LED current protection to ensure reliable operation.
Product overview video demonstrating the LED Driver Module.
2. Specifications
| Feature | Specification |
|---|---|
| Working Voltage | DC 2.8V-6V (Ideal for 3V, 3.3V, 3.7V, 4.5V, 5V, 6V LED drivers) |
| Output Current | 30-1500mA (0.03-1.5A) |
| Maximum Output Power | 9W |
| Drivable LEDs | 1-16 pieces of 2.8-6V LEDs (maximum current not exceeding 1.5A) |
| Current Regulation | Adjustable resistance or PWM signal control |
| PWM Signal Frequency | Less than 2KHz |
| Features | Chip Temperature Regulation, Over LED Current Protection |
| Dimensions | 18mm x 10.3mm x 2.8mm |
| Weight | 0.01kg |
| Certification | CCC, CE, ROHS |
| Item Type | Lighting Transformers |
| Origin | Mainland China |

Front view of the LD06AJSA/B LED Driver Module, showing the main chip, adjustable resistor, and connection pads.

Back view of the LD06AJSA/B LED Driver Module, showing the heat dissipation pad.
3. Safety Information
- Ensure the input voltage is within the specified range (DC 2.8V-6V) to prevent damage to the module and connected LEDs.
- Observe correct polarity when connecting power and LEDs. Incorrect connections can cause permanent damage.
- Avoid short circuits on the output terminals.
- When adjusting the current via the adjustable resistor, use a suitable non-conductive screwdriver and rotate gently and slowly to prevent damage to the component.
- Do not exceed the maximum output power of 9W or the maximum current of 1.5A.
- The module may generate heat during operation. Ensure adequate ventilation and do not enclose it in a way that prevents heat dissipation.
4. Setup and Installation
4.1. Module Pinout
The module features several connection pads:
- V1: Input Voltage (DC 2.8V-6V)
- CE: Output Enable / PWM Control Port (Active High)
- G: Ground
- LED: LED Output (Connect to LED anode)

Diagram illustrating the output current regulation via the adjustable resistor and the function of the CE pin as an output enable/PWM control port.
4.2. Application 1: Adjustable Current via Potentiometer
This application allows you to set a constant output current using the onboard adjustable resistor (potentiometer).
- Connect the DC power source (2.8-6V) to the V1 (positive) and G (ground) pads.
- Connect your 1 to N LEDs in parallel to the LED (positive) and G (ground) pads. Ensure the total current draw does not exceed 1.5A.
- Ensure the CE pin is high (connected to V1 or a logic high signal) for the module to function.
- Using a suitable screwdriver, gently and slowly rotate the adjustable resistor (labeled ADJ) to increase or decrease the output current to your desired level.

Wiring diagram for setting output current using the adjustable resistor. Rotate the ADJ potentiometer to adjust the current.
4.3. Application 2: PWM Regulated Output Current
This application allows dynamic control of the LED output current using a Pulse Width Modulation (PWM) signal from a microcontroller (MCU).
- Connect the DC power source (2.8-6V) to the V1 (positive) and G (ground) pads.
- Connect your 1 to N LEDs in parallel to the LED (positive) and G (ground) pads.
- Adjust the onboard adjustable resistance (ADJ) to 0 ohms (or maximize the current according to Application 1). This sets the maximum current.
- Connect the MCU's PWM output pin to the CE pin of the module. The PWM signal frequency should be less than 2KHz.
- The MCU's PWM signal will now control the LED output current. The CE pin can be driven by TTL or COMS logic levels.

Wiring diagram for controlling output current using a PWM signal from an MCU. The adjustable resistor should be set to 0 ohms or maximum current.
5. Operating Instructions
5.1. Current Regulation
The LD06AJSA/B module is a current regulation integrated circuit. The constant output current can be set up to 1.5A with an external resistor (the adjustable resistor on the module). The module consists of a high precision reference voltage, amplifier, and current mirror. The on-chip power transistor and current sense block greatly reduce the external component count, making it ideal for LED driver applications.
5.2. Chip Enable (CE) Function
When the CE pin is high, and the input voltage is greater than 2.8V (and also larger than the LED forward voltage plus the required voltage drop), the LD06AJSA/B functions normally to deliver constant current from the LED pin. The CE pin also serves as the PWM control port, allowing external microcontrollers to modulate the output current.
5.3. Temperature Regulation
The LD06AJSA/B adopts temperature regulation instead of a simple temperature protection function. This allows the LED to remain continuously turned on even in cases of high ambient temperature or high voltage drop. When the module's junction temperature reaches approximately 135°C, the internal temperature regulation block automatically reduces the LED current. This prevents the junction temperature from rising further, maximizing the power handling capability of the chip without causing overheating or damage to the chip or external components.
5.4. Over Current Protection
The module includes an over current protection block. If the LED current approaches 1.9A (typical), this block activates to prevent the LED current from increasing further, safeguarding the LEDs and the module from excessive current.
6. User Tips
- The adjustable resistor (potentiometer) on the module is crucial for setting the output current. If you need to replace it or are curious about its range, it's typically a multi-turn trimmer potentiometer. While the exact resistance value isn't specified, its purpose is to provide a variable resistance for current adjustment.
- For precise current control, especially in PWM applications, ensure your microcontroller's PWM signal is stable and within the recommended frequency range (<2KHz).
- Consider using a multimeter to verify the output current to your LEDs after initial setup, especially when using the adjustable resistor for the first time.
7. Troubleshooting
- LEDs not lighting up: Check input voltage, ensure correct polarity for power and LEDs, verify CE pin is high (or receiving a PWM signal), and inspect all connections for continuity.
- LEDs too dim/bright: Adjust the onboard potentiometer (ADJ) or check your PWM signal if using Application 2. Ensure the LEDs are compatible with the module's voltage and current capabilities.
- Module overheating: Ensure the total LED current does not exceed 1.5A and the total power does not exceed 9W. Verify adequate ventilation around the module. The internal temperature regulation should prevent damage, but excessive heat can reduce efficiency and lifespan.
- Intermittent operation: Check for loose connections, cold solder joints, or unstable input power.
8. Maintenance
- Keep the module clean and free from dust and debris.
- Avoid exposing the module to moisture or extreme temperatures.
- Regularly inspect connections for any signs of wear or corrosion.
9. Warranty and Support
For detailed information regarding warranty, returns, or technical support, please refer to the official product page or contact the seller directly. A comprehensive user manual in PDF format is also available for download: