1. Introduction
This USB Programming Cable (Model: USB-AT5N) is designed to connect your compatible Citizen Band (CB) radio to a computer, allowing you to program and customize its settings using dedicated software. This manual provides essential information for setting up, operating, and maintaining your programming cable.
2. Setup Instructions
Before connecting the cable, ensure you have the appropriate programming software and USB drivers installed on your computer. These are typically provided by the radio manufacturer or can be found online.
- Install Drivers and Software: If not already installed, download and install the necessary USB drivers for the programming cable and the specific programming software for your CB radio model onto your computer.
-
Connect to Radio: Locate the programming port on your CB radio. This is typically a mini-USB port. Connect the mini-USB end of the programming cable to this port on your radio.
Figure 2: Connecting the mini-USB end to the radio's programming port. -
Connect to Computer: Connect the standard USB-A end of the programming cable to an available USB port on your computer.
Figure 3: The USB-A and mini-USB connectors of the cable. - Power On Radio: Ensure your CB radio is powered on after connecting the cable.
Watch the video below for a visual guide on connecting the programming cable to a CB radio:
3. Operating Instructions
Once the cable is connected and drivers/software are installed, you can proceed with programming your radio:
- Launch Software: Open the programming software on your computer.
- Select COM Port: In the software settings, select the correct COM port that corresponds to your USB programming cable. This is usually detected automatically or can be found in your computer's Device Manager.
- Read Radio Data: Use the software's 'Read from Radio' or 'Download' function to retrieve the current settings from your CB radio. This is a good practice to back up your existing configuration.
- Modify Settings: Adjust frequencies, channels, squelch levels, and other parameters as needed within the programming software interface.
- Write to Radio: After making your desired changes, use the software's 'Write to Radio' or 'Upload' function to transfer the new settings to your CB radio. Follow any on-screen prompts or radio-specific instructions.
- Verify: After writing, it's recommended to read the radio data again to confirm the new settings have been successfully applied.
This cable is confirmed to be compatible with the following radio models:
- AnyTone AT-5555N II
- AnyTone ARES II
- CRT 8900
- CRT 9900
- Lincoln 2+
- Voyager VR5555N2
- Dynascan 10-meter radio
4. Maintenance
- Storage: Store the cable in a cool, dry place, away from direct sunlight and extreme temperatures. Avoid tightly coiling or kinking the cable to prevent internal damage.
- Cleaning: If necessary, gently wipe the cable with a soft, dry cloth. Do not use harsh chemicals or abrasive materials.
- Handling: Always grasp the connector ends when plugging or unplugging the cable, rather than pulling on the cable itself.
5. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Cable not recognized by computer | Missing or incorrect USB drivers. Faulty USB port. |
|
| Programming software cannot connect to radio | Incorrect COM port selected. Radio not powered on. Incompatible software/firmware. |
|
| Programming errors or data corruption | Interrupted connection. Incorrect settings. |
|
6. Specifications
| Feature | Detail |
|---|---|
| Item Type | Programming Cable |
| Model Number | USB-AT5N |
| Brand Name | AnyTone |
| Compatibility | AnyTone AT-5555N II, ARES II, CRT 8900, CRT 9900, Lincoln 2+, Voyager VR5555N2, Dynascan 10-meter radio, and other compatible CB radios with a mini-USB programming port. |
| Connector Type (Radio) | Mini-USB |
| Connector Type (Computer) | USB-A |
| Package Dimensions (approx.) | 15 cm (Length) x 13 cm (Width) x 2 cm (Height) |
| Package Weight (approx.) | 0.03 kg |
7. User Tips
- Many users have confirmed successful programming with various radios including AnyTone Ares II, CRT 8900, CRT 9900, Lincoln 2+, and Voyager VR5555N2.
- The necessary programming software for your specific radio model is typically available online from the radio manufacturer or community forums.
- Always ensure you have the correct and latest drivers installed for the programming cable to avoid connectivity issues.
8. Support and Warranty
For technical assistance or support regarding this USB programming cable, please contact the seller or manufacturer. This cable, as an accessory, typically comes with a 6-month warranty from the date of receipt. Please retain your purchase records for warranty claims.
For issues related to your CB radio's programming software or specific radio functions, refer to your radio's user manual or contact the radio manufacturer's support.