1. Introduction
Congratulations on your new ANDELI product! This manual provides essential information for the safe and efficient operation, installation, maintenance, and troubleshooting of your MIG-135 PLUS 3-in-1 Inverter Welding Machine. Please read this manual thoroughly before using the equipment to ensure your safety and optimize performance.
The ANDELI MIG-135 PLUS is a versatile welding machine designed for various applications, offering MIG, MMA (Stick), and Lift TIG welding capabilities. It features a 4.1-inch precision LED display with a transparent protective cover, smart synergic control, and advanced protection systems.

Figure 1.1: ANDELI MIG-135 PLUS Welder
2. Safety Information
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights:
2.1. General Safety Precautions
- ELECTRIC SHOCK CAN KILL: Do not touch electrically live parts. Insulate yourself from the work and ground. Wear dry, insulating gloves.
- FUMES AND GASES CAN BE DANGEROUS: Avoid breathing fumes and gases. Use adequate ventilation or exhaust at the arc to keep fumes and gases away from your breathing zone.
- WELDING SPARKS CAN CAUSE FIRE OR EXPLOSION: Remove fire hazards from the welding area. Do not weld on closed containers. Have a fire extinguisher readily available.
- ARC RAYS CAN BURN: Use a shield with proper filter plates to protect your eyes. Wear suitable clothing to protect your skin from arc rays.
- CYLINDER MAY EXPLODE IF DAMAGED: Use only compressed gas cylinders containing the correct shielding gas. Secure cylinders to prevent falling.
- ELECTRIC AND MAGNETIC FIELDS (EMF) MAY BE DANGEROUS: Welding current creates EMF fields. Welders with pacemakers should consult their physician.
2.2. Specific Safety Warnings
- Always ensure all installation, operation, maintenance, and repair procedures are performed by qualified individuals.
- When feeding a new wire through the liner, ensure the wire is cut cleanly and straight to prevent damage to the liner.
- Do not bring your face near the gun or fingers close to the feeding mechanism when checking wire exit, as moving rolls may crush fingers.
- TIG torch is always live (electrically hot). Use caution and ensure it is not in contact with conductive or grounded material.
3. Product Overview
The ANDELI MIG-135 PLUS is a compact, portable, and versatile inverter welding machine. It supports three primary welding processes:
- Flux-Cored (FCAW) / MIG Welding: Ideal for various materials and outdoor use, especially with flux-cored wire which eliminates the need for external shielding gas.
- Stick Welding (SMAW): Portable and versatile for welding in various positions and on thicker materials.
- Lift TIG Welding (GTAW): Provides high-quality, precise welds on thin materials with excellent control.
3.1. Key Features
- 4.1-Inch Precision LED Display: Oversized display for crystal-clear visibility and real-time data.
- Reinforced Protective Cover: Safeguards the display from impacts, sparks, and debris.
- Smart Synergic Control Technology: Automatically optimizes voltage and wire feed speed based on amperage or wire diameter.
- Advanced Protection & Stability System: Includes automatic voltage compensation, over-current, overload, overheating, and over-voltage protection.
- 2T/4T Settings: Manual and automatic modes for different usage scenarios.

Figure 3.1: Large LED Display with Protective Cover

Figure 3.2: Smart Synergic Control Interface

Figure 3.3: 4-in-1 Multi-Process Capabilities

Figure 3.4: Material Suitability

Figure 3.5: Excellent Welding Effect Examples

Figure 3.6: Perfect for Daily Repair

Figure 3.7: 2LB Welding Wire Application

Figure 3.8: 2T/4T Settings
4. Technical Specifications
The following table details the technical specifications for the ANDELI MIG-135 PLUS Inverter DC Welding Machine:

Figure 4.1: Welder Dimensions and Weight
| Attribute | Value |
|---|---|
| Brand Name | ANDELI |
| Model Number | MIG-135 |
| Origin | Mainland China |
| Dimensions | 330*150*238mm (12.99*5.91*9.37 inches) |
| Weight | 4.1kg (9.1 LB) |
| Certification | CE |
| Use | Welding |
| Frequency | 50/60Hz |
| Current Range | 20-135A |
| Is Smart Device | No |
| High-concerned chemical | None |
| Mode | Duty Cycle | Current | Volts at Rated Current |
|---|---|---|---|
| GMAW (MIG) | 20% | 135A | 20.8V |
| 60% | 78A | 17.9V | |
| 100% | 60A | 17V | |
| GTAW (TIG) | 20% | 135A | 15.4V |
| 60% | 78A | 13.1V | |
| 100% | 60A | 12.4V | |
| SMAW (STICK) | 20% | 135A | 25.4V |
| 60% | 78A | 23.1V | |
| 100% | 60A | 22.4V |
| Attribute | Value |
|---|---|
| Open Circuit Voltage | 56V |
| Power Factor | 0.7 |
| Efficiency | ≥80% |
| Protection Class | IP21S |
| Insulation Class | F |
| Operating Temperature Range | -10°C ~ +40°C (14°F ~ 104°F) |
| Storage Temperature Range | -20°C ~ +55°C (-4°F ~ 131°F) |
5. Accessories
The following accessories are typically included with your ANDELI MIG-135 PLUS welder:
- Welding Wires
- Work Clamp
- Electrode Holder
- Contact Tips (2 Pcs)
- MIG Torch
- MIG 135 Plus Welder Unit

Figure 5.1: Welder and Accessories
6. Installation
ELECTRIC SHOCK CAN KILL! Only qualified personnel should perform this installation. The machine must be plugged into a grounded receptacle per national, local, or other applicable electrical codes. The MIG-135 power switch should be in the OFF position when installing the work cable and gun and connecting the power cord to input power.
6.1. Selecting a Suitable Location
Locate the MIG-135 in a dry place with free, clean air circulation to minimize the chance of dirt accumulation that can block air passages and cause overheating. The machine cannot be stacked. It should be placed on a secure, level surface or a recommended cart to prevent toppling.
6.2. Controls and Operational Features Overview

Figure 6.1: Front Panel Controls
- 1. Diameter Button / 2T 4T Button: For switching wire diameter (0.8/0.9/1.0mm) and selecting 2T/4T modes.
- 2. LED Digital Display: Shows real-time welding parameters.
- 3. Inching Button: For manual wire feeding.
- 4. Voltage / Inductance Adjustment Knob: Adjusts welding voltage and inductance.
- 5. Current Adjustment / Function Selection Knob: Selects welding mode (MMA/LIFT TIG/SYN) and adjusts current.
- 6. MIG Torch Socket: Connection point for the MIG torch.
- 7. Negative Output Terminal: Connects to the work clamp or electrode holder depending on polarity.
- 8. Control Switch Socket: For connecting the MIG torch control switch.
- 9. Positive Output Terminal: Connects to the work clamp or electrode holder depending on polarity.

Figure 6.2: Rear Panel Features
- 1. Power Switch: Turns the machine on/off.
- 2. Input Power Cable: Connects to AC power source.
- 3. Fan: Provides cooling for the machine.
- 4. Ground Screw: For grounding the machine.
- 10. Wire Spool Spindle and Brake: Holds the welding wire spool.
- 11. Wire Feeder & Components: Mechanism for feeding welding wire.
6.3. Installing the MIG Gun Assembly
Connect the standard gun to the Euro Torch Connector on the front of the welder. Ensure the gun connector is fully inserted into the wire drive system, then tighten the thumbscrew to secure it in place.
6.4. Gas Cylinder and Regulator Connection (for MIG welding)
For MIG welding, a separate gas cylinder and regulator are required. The gas hose connects from the machine's rear gas inlet to the regulator, which is then attached to the gas cylinder. Position the cylinder securely in a well-ventilated area.
WARNING: Cylinders are highly pressurized. Handle with care. Serious accidents can result from improper handling or misuse of compressed gas cylinders. Do not drop, knock over, or expose to excessive heat, flames, or sparks. Do not strike it against other cylinders or strike an arc on it.
6.5. Installing the Welding Wire
ENSURE GAS AND ELECTRICAL SUPPLIES ARE DISCONNECTED. Before proceeding, remove the nozzle and the contact tip from the gun.
WARNING: ELECTRIC SHOCK CAN KILL! Always turn the Power SWITCH OFF and unplug the welder's INPUT POWER CABLE from the AC power source before installing wire. When the gun trigger is depressed, the drive rolls, spool of wire, wire being fed, and electrode are all electrically live (hot).
- Open the access panel.
- Remove the nut, nut washer, spring, and spool spacer.
- Remove the outer wrapping from the wire spool.
- Place the spool on the WIRE SPOOL SPINDLE so that the wire unspools from the bottom and rotates counterclockwise.
- Replace the spool spacer, spring, nut washer, and nut.
- Adjust the nut to an appropriate degree so that the wire spool won't spin freely when released.
- Cut off the bent end of the wire, leaving a straight end.
- Release the drive roller pressure arm.
- Insert the wire into the inlet guide tube, across the drive roller, and into the torch assembly.
- Align the wire in the inner groove of the drive roller and drop the pressure arm. Tighten the pressure adjusting knob until sufficient force is applied to prevent slipping.
- Remove the nozzle and contact tip from the end of the torch assembly.
- Plug the welder's INPUT POWER CABLE into the AC power socket.
- Pull the trigger on the MIG torch to feed the wire through the torch assembly until at least 25.4MM of wire protrudes.
- Slide the contact tip over the wire and screw it firmly into the torch.
- Install the nozzle on the torch assembly.
- Cut off any excess wire.
7. Operation
7.1. Welding Preparation
Preparation is key to good welds. Ensure your work area is organized, safe, ergonomic, and well-lit. Remove all flammables and have a fire extinguisher and sand bucket available.
- Read safety precautions.
- Prepare an organized, well-lit work area.
- Protect eyes and skin of operator and bystanders.
- Attach the work clamp to clean, bare metal for good contact.
- Ensure wire-roller groove matches wire diameter and type.
- Plug machine into suitable power outlet.
- Completely open gas cylinder valve and adjust flow rate (if applicable).
EXPOSURE TO A WELDING ARC IS EXTREMELY HARMFUL TO THE EYES AND SKIN. WEAR FIRE RESISTANT WELDING GLOVES, HEAVY LONG SLEEVED SHIRT, CUFFLESS PANTS; HIGH TOPPED SHOES AND A WELDING HELMET.
7.2. Home Menu Setup
After powering on, the "Home Menu" will be lit. Here you can choose the welding mode and adjust basic settings. The machine will automatically return to the screen used prior to shut-down if restarted. To access the main menu, press the Menu button on the panel.

Figure 7.1: Two Control Modes
7.3. Flux-Cored (SYN) Welding Steps
- Torch Installation: Insert the MIG torch into the MIG torch socket and screw in clockwise. Install the torch control switch onto the panel switch socket.
- Ground Clamp Installation: Connect the work clamp cord to the positive (+) terminal.
- Welding Wire Installation: Install the welding wire (refer to Section 6.5 for details), and then turn on the power switch. The fan will start to work.
- Mode Selection: Press the D knob to select SYN.
- Operation Instructions: Press the B button on the panel; the wire will feed automatically. The longer you press the button, the faster the speed will be. Or you can press the torch trigger until the wire extends to the nozzle. (The nozzle may need to be removed from the torch to allow this function.)
- Wire Diameter Selection: Press the A button to select 0.8/0.9/1.0.
- Set the Welding Current: Set the welding current with the D knob.
- Welding Technique Selection: Press the A Button for 3s to enter and exit the 2T/4T interface, touch to select.
- Inductance Adjustment: Press the C Knob for 3s to enter, rotate the knob to adjust the inductance value (-9.9 to +9.9), and press it again to exit.
7.4. Flux-Cored (MAN) Welding Steps
The installation steps are consistent with the SYN mode.
- Wire Diameter Selection: Press the A button to select 0.8/0.9/1.0.
- Welding Current: Set the welding current with the D knob.
- Welding Voltage: Set the welding voltage with the C knob.
- Welding Technique Selection: Press the A Button for 3s to enter and exit the 2T/4T interface, touch to select.
- Inductance Adjustment: Press the C Knob for 3s to enter, rotate the knob to adjust the inductance value (-9.9 to +9.9), and press it again to exit.
7.5. Stick Welding (SMAW) Setup
- Remove the Wire Drive Polarity Lead from the Positive (+) Output and Negative (-) Output Terminal.
- Check electrode packaging for recommended polarity. Connect the electrode holder and work clamp accordingly.
- Place the electrode into the electrode holder firmly.
- Ensure the work clamp has good contact with the metal.
- Turn the power source on and select the Stick welding process (MMA) with the Function Knob.
- Set the amperage with the Value Adjustment Knob.
- Strike the electrode against the workpiece to create an arc and hold steady.
- To finish, break the arc by quickly snapping the electrode away.
7.5.1. Polarity Setup for Stick Welding (SMAW)
- DCEP (Direct Current Electrode Positive): Connect the electrode holder to the Positive (+) Output Terminal and the work clamp to the Negative (-) Output Terminal. Recommended for most stick welding applications, providing deeper penetration on thicker materials.
- DCEN (Direct Current Electrode Negative): Connect the electrode holder to the Negative (-) Output Terminal and the work clamp to the Positive (+) Output Terminal. Recommended for welding thin metals or when required by specific electrode types.
7.6. Lift Arc TIG Welding (GTAW) Setup
WARNING: TIG TORCH IS ALWAYS LIVE (ELECTRICALLY HOT). Use caution and ensure the TIG torch is not in contact or close to a conductive or grounded material.
- Remove the Wire Drive Polarity Lead from the Positive (+) Output and Negative (-) Output Terminals.
- Connect the TIG torch cable to the welder's Negative (-) Output Terminal.
- Connect the work cable connector to the welder's Positive (+) Output Terminal.
- Ensure the work clamp has good contact with the workpiece on a clean, bare metal surface.
- Connect the TIG torch gas line to the gas regulator (use 100% Argon gas only). Turn on the gas at the regulator, check for gas flow, and adjust the flow rate as needed.
- Set the tungsten electrode to extend approximately 6.35MM from the gas cup. Ensure you are using the correct size and type of tungsten electrode.
7.6.1. TIG Torch Assembly
Assemble the TIG torch correctly to ensure proper shielding, arc stability, and optimal welding performance.

Figure 7.2: TIG Torch Assembly Diagram
- Install the Collet Body into the Torch Head securely.
- Place the Collet inside the Collet Body.
- Insert the Tungsten Electrode through the Collet, leaving 3.2MM to 6.2MM extending from the gas nozzle.
- Screw the Back Cap onto the rear of the Torch Head to lock the tungsten electrode in place.
- Attach the Insulator Torch Body over the Torch Head to protect the assembly from heat.
- Thread the Ceramic Gas Nozzle onto the Collet Body for proper shielding gas coverage.
REMEMBER TO CLOSE THE VALVE ON THE GAS CYLINDER IMMEDIATELY AFTER ALL WELDING IS COMPLETED.
8. Maintenance & Servicing
8.1. General Maintenance
- Keep the cabinet cover closed unless changing wire or adjusting pressure.
- Keep all consumables (contact tips, nozzles, and liner) clean and replace when necessary.
- Replace INPUT POWER CABLE, ground cable, work clamp, or gun assembly when damaged or worn.
- Avoid directing grinding particles towards the welder.
- Periodically clean dust, dirt, grease, etc., from your welder. Remove side panels and use compressed air to blow out accumulated dust and dirt.
WARNING: DISCONNECT FROM POWER SOURCE WHEN CARRYING OUT THIS OPERATION. The ON/OFF SWITCH does not remove power from all internal circuitry. Always unplug the welder from its AC power source and wait several minutes for energy to discharge before removing side panels.
8.2. Consumable Maintenance
It is very important to maintain the consumables to avoid the need for premature replacement of the gun assembly.
- Contact Tip: Use a contact tip stamped with the same diameter as the wire. Clean or replace if wire burns back or the hole is worn.
- Gas Nozzle: Keep the gas nozzle clean. Periodically clean spatter and slag buildup. Replace if damaged or clogged to prevent erratic welds and overheating.
9. Troubleshooting
This guide helps locate and fix possible machine malfunctions. Follow these steps:
- Locate Problem (Symptom): Find the listing that best describes the symptom your machine is exhibiting.
- Possible Cause: Review the obvious external possibilities that may contribute to the symptom.
- Recommended Course of Action: Follow the suggested action. If you cannot perform the action safely, contact ANDELI support.
9.1. General Troubleshooting
| Problem | Possible Cause | Course of Action |
|---|---|---|
| OVER HOT | Welding current exceeds machine's capacity | Reduce welding current or contact support for assistance. |
| Machine is drawing too much amperage due to use of larger size electrode. | Use a smaller electrode. | |
| Frequent circuit breaker trips | Machine is not the only piece of electrical equipment on the circuit. | Make sure the welder is on a dedicated circuit or is the only equipment plugged into a circuit. |
| Circuit breaker is incorrect/insufficient for use with this machine. | Verify that the circuit breaker for the circuit is a 30A breaker for 120V and 20A for 240V. If not, have a qualified electrician install the proper breakers. | |
| Screen's OFF, No output power, Fan not operating | No input power. | Connect machine to proper input power source. Verify that circuit breaker has not been tripped in your main power panel. Reset if needed. |
| POWER SWITCH is OFF. | Ensure POWER SWITCH (rear) is in the ON position. | |
| Screen is OFF, but fan is operating | Power supply issue. | Check and secure power connections to display/control board. |
| Control board malfunction | Contact our support team for further assistance and repair. |
9.2. MIG Welding Issues
| Problem | Possible Cause | Course of Action |
|---|---|---|
| No arc or wire feed | Gun trigger is not being pulled or is not making contact. | Ensure the trigger is fully pulled. Inspect and replace the trigger switch if it is faulty. |
| Incorrect gun mode selected. | Check and adjust the gun mode settings to match the correct gun type. | |
| Exceeded duty cycle; thermal protection engaged. | Allow the machine to cool down. Stay within the machine's duty cycle to avoid overheating. | |
| Insufficient air flow causing machine to overheat. | Ensure proper ventilation and airflow around the machine. Check the fan for blockages or malfunctions. | |
| Feed motor operates but wire will not feed | Wire Feed Motor Fault. | Inspect the wire feed motor and connections. Replace if necessary. |
| Control Board Malfunction. | Inspect the control board for damage. Contact our support team for further assistance and repair. | |
| Blocked or Worn Contact Tip. | Clean or replace the contact tip. Ensure it's the right size for the wire. | |
| Insufficient feed drive roller pressure. | Adjust drive roller pressure. | |
| Burr on end of wire. | Re-cut wire so it is square with no burr. | |
| Liner blocked or damaged. | Clear with compressed air or replace liner. | |
| Wire feeds but no arc | Poor ground connection. | Ensure the ground clamp is securely attached to clean, bare metal. |
| No gas flow (if MIG welding with solid wire). | Check the gas flow and ensure the cylinder is not empty and the regulator is set properly. | |
| Settings may be incorrect, preventing arc formation. | Adjust the voltage, wire feed speed, and other arc settings to match the material and process. | |
| Control board malfunction. | Inspect the control board for issues. Contact our support team for further assistance and repair. | |
| Faulty or dirty nozzle. | Clean or replace the nozzle. | |
| Faulty contact tip. | Inspect and replace the contact tip if worn out or damaged. | |
| Trigger not pulled while wire is in contact with workpiece. | Pull the trigger while in contact with the workpiece. The machine does not arc unless the trigger is pulled. | |
| Internal connection issue in the welding machine. | Check internal machine connections or contact technical support. |
9.3. Error Codes and Solutions
- E01 (Overheating): Welding is forced to stop because the main circuit is overheated. Wait a few minutes until the indicator turns off and the error code disappears.
- E02 (Over-current): Indicates an over-current condition. Restart the machine.

Figure 9.1: Transparent Protective Cover
10. User Tips
- For Beginners: The automatic (SYN) mode is highly recommended as it simplifies current and voltage matching.
- Wire Compatibility: The machine works well with flux-cored wire, eliminating the need for external gas. It can handle 0.8mm and 1.0mm wire diameters.
- Welding Aluminum: This machine is not designed for welding aluminum as it requires AC current, which is not available.
- Minimum Current: The minimum effective welding current is around 30 amps, which might be too high for very thin materials, potentially causing burn-through.
- Wire Feed Rollers: The wire feed rollers are typically steel, but the overall mechanism might contain plastic parts. Ensure proper tension to avoid slipping or crushing the wire.
- TIG Welding: For Lift TIG, argon gas is needed. The machine does not have a built-in gas solenoid, so manual gas flow management is required.
11. Warranty & Support
ANDELI is committed to providing quality products and support. For further questions or assistance, please refer to the following:
- Official Website: www.andelitools.com
- After-sales Email: support@andeligroup.com
- After-sales Number (USA): +1 949 617 9002
- After-sales Number (Hong Kong): +852 8480 7265
- User Manual (PDF): A detailed user manual in PDF format is available for download. View User Manual (PDF)
We encourage you to join the ANDELI community for tips and discussions.
Video 11.1: ANDELI MIG-135 PLUS Product Demonstration