1. Introduction
This manual provides detailed instructions for the safe and effective use, maintenance, and care of your Nasedal NT-116B Double Action Gravity Feed Spray Gun. This professional-grade airbrush kit is designed for a wide range of applications, offering precise control and versatility.
2. Package Contents
Please verify that all items listed below are included in your package:
- 1 x Dual-Action 0.5mm Airbrush
- 1 x 2cc Fluid Cup
- 1 x 5cc Fluid Cup
- 1 x 13cc Fluid Cup
- 1 x 0.3mm Needle, Nozzle, Nozzle Cap Set
- 1 x 0.8mm Needle, Nozzle, Nozzle Cap Set
- 1 x Air Hose (1.8m / 5.9ft)
- 1 x Mini Wrench
- 1 x Storage Case
- 1 x User Manual (this document)


3. Product Features
The Nasedal NT-116B airbrush is crafted from copper and features a pistol trigger design for comfortable and precise control. Key features include:
- Double Action Trigger: Allows independent control of both air and fluid for fine adjustments.
- Gravity Feed Design: Ensures consistent paint flow and is ideal for small amounts of paint.
- Interchangeable Needles & Nozzles: Includes 0.3mm, 0.5mm (pre-mounted), and 0.8mm sets for various spray patterns, from hairline to 2 inches wide.
- Multiple Fluid Cup Capacities: Comes with 2cc, 5cc, and 13cc screw-on cups to suit different project sizes.
- Precise Nozzle: Designed for accurate and detailed work.
- Stainless Steel Needles: Durable and resistant to corrosion.
- Atomization Size Control Knob: Located at the rear of the airbrush for adjusting the spray pattern.
- Adjustable Air Outlet Size: Provides further control over the air flow.
- Anti-slip Handle: Ergonomically designed for comfortable grip and reduced fatigue.


4. Setup Instructions
Before using your airbrush, ensure all components are clean and properly assembled.
4.1 Assembling the Airbrush
- Select Needle and Nozzle: Choose the appropriate needle, nozzle, and nozzle cap set (0.3mm, 0.5mm, or 0.8mm) for your desired spray pattern. The 0.5mm set is pre-mounted.
- Attach Fluid Cup: Screw the desired fluid cup (2cc, 5cc, or 13cc) onto the top of the airbrush body.
- Connect Air Hose: Attach one end of the air hose to the air inlet at the bottom of the airbrush handle.
- Connect to Air Compressor: Connect the other end of the air hose to your air compressor. Note: An air compressor is not included with this airbrush kit. Ensure your compressor is compatible and provides a working pressure of 15-50 PSI.

4.2 Initial Test
Before applying paint, perform a test spray with water to ensure proper function and familiarize yourself with the airbrush controls.
Video 1: Unboxing and Basic Functionality Demonstration (Note: Air compressor not included)
5. Operating Instructions
5.1 Preparing Paint
Thin your fluid (paint, ink, etc.) appropriately according to the manufacturer's recommendations for airbrush use. The consistency should be similar to milk for optimal atomization.
5.2 Spraying Technique
- Fill Fluid Cup: Carefully pour the appropriately thinned fluid into the attached fluid cup.
- Hold Airbrush: Hold the airbrush lightly and comfortably in your hand, maintaining a steady grip.
- Initiate Airflow: Press the main trigger lever down to release a stream of air.
- Control Fluid Flow: While maintaining airflow, gradually pull the trigger lever backward to atomize and release the color. The further back you pull, the more fluid will be released.
- Adjust Spray Pattern: The spray pattern's width and intensity are controlled by the distance between the airbrush and the work surface, as well as the atomization size control knob at the rear of the airbrush.
- Fine Line Spray: For very fine lines, remove the needle cover (if attached) and hold the airbrush very close to the work surface.

6. Maintenance and Cleaning
Regular cleaning is crucial for maintaining the performance and longevity of your airbrush. Clean immediately after each use, especially when changing colors or finishing a session.
- Empty Fluid Cup: Empty any remaining fluid from the cup.
- Initial Rinse: Fill the fluid cup with water or an appropriate solvent (depending on the paint type) and clean it thoroughly with a brush.
- Flush System: Refill the cup with water or solvent. Block the needle cover with your finger and spray. The air will flow backward into the nozzle, helping to clean any remaining paint. Repeat until the solvent sprays clear.
- Disassemble for Deep Cleaning: Periodically, or if clogging occurs, disassemble the airbrush components (needle, nozzle, nozzle cap, fluid cup) and clean them individually with appropriate cleaning solutions and brushes.
- Lubrication: Apply a small amount of airbrush lubricant to the needle and trigger mechanism as needed to ensure smooth operation.
7. Troubleshooting
Here are some common issues and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No paint flow | Clogged nozzle/needle, paint too thick, insufficient air pressure. | Clean nozzle/needle, thin paint, check air compressor pressure. |
| Splattering or inconsistent spray | Paint too thin, damaged needle/nozzle, air pressure too high/low. | Adjust paint consistency, inspect/replace parts, adjust air pressure. |
| Air bubbles in fluid cup | Loose nozzle, damaged nozzle, clogged air cap. | Tighten nozzle, replace nozzle, clean air cap. |
| Trigger sticking | Dried paint in mechanism, lack of lubrication. | Clean trigger area, apply airbrush lubricant. |
Note: An air compressor is required for operation and is not included with this airbrush. Ensure you have a compatible compressor that can provide the necessary working pressure (15-50 PSI).
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Nasedal |
| Model Number | NT-116B |
| Type | Mini Spray Gun (Double Action Gravity Feed Airbrush) |
| Material | Copper |
| Power Type | Pneumatic |
| Feed Type | Gravity |
| Nozzle Diameter | 0.3mm, 0.5mm, 0.8mm |
| Needle Diameter | 0.3mm, 0.5mm, 0.8mm |
| Fluid Cup Capacity | 2CC, 5CC, 13CC |
| Hose Length | 1.8m / 5.9ft |
| Working Pressure | 15-50 PSI |
| Airbrush Size | Approx. 16 * 2.2 * 10cm / 6.3 * 0.9 * 3.9in |
| Airbrush Weight | Approx. 153.1g / 5.4oz |
| Hose Weight | Approx. 103g / 3.6oz |
| Package Size | Approx. 23.5 * 17.5 * 4.5cm / 9.3 * 6.9 * 1.8in |
| Package Weight | Approx. 687g / 24.2oz |
| Battery Included | No |
| High-concerned chemical | None |
| Origin | Mainland China |
| Certification | NONE |
9. Applications
The Nasedal NT-116B airbrush is versatile and suitable for a wide range of creative and practical applications, including but not limited to:
- Illustration and Fine Commercial Art
- Photo Retouching
- Custom Automotive and Motorcycle Graphics
- T-Shirts & Textiles
- Nail Art & Cosmetics
- Temporary Tattoos
- Model Making (RC's, Trains, etc.)
- Hobbies & Crafts
- Cake Decorating
- Body Painting
- Wall Painting


10. User Tips
- Needle Identification: The airbrush comes with a 0.5mm needle pre-installed. Additional 0.3mm and 0.8mm needles and nozzles are included in the kit for different spray requirements.
- Compressor Compatibility: This airbrush requires an external air compressor. Ensure your compressor can deliver a stable pressure between 15-50 PSI for optimal performance.
- Paint Thinning: Always thin your paints to the correct consistency (typically like milk) to prevent clogging and ensure smooth atomization.
- Immediate Cleaning: Clean your airbrush immediately after each use and when changing colors to prevent paint from drying and clogging the delicate parts.
- Regular Maintenance: Perform regular deep cleaning and lubrication to keep the airbrush in top working condition.
11. Warranty and Support
For any issues or questions regarding your Nasedal NT-116B airbrush, please refer to the seller's support channels. Keep your purchase records for warranty claims, if applicable. Specific warranty terms may vary by region and seller.