TECNR SF-HC30A3

Contents

STARFIRE SF-HC30A3 Automatic Torch Height Controller

User Manual

1. Introduction

The STARFIRE SF-HC30A3 is an advanced automatic torch height controller (THC) designed for CNC plasma and flame cutting machines. This model is an upgrade from previous versions (SF-HC30A0 and SF-HC30A1), offering enhanced performance and reliability with the same connection and functionality.

Key features of the SF-HC30A3 include:

  • Stepper Motor Control: Replaces conventional DC motors for rapid, smooth, and extended service life.
  • Integrated Design: Detector, controller, and actuator are integrated into a single unit, allowing for a 10cm adjustment range.
  • All-Digital Technology: Utilizes patch technology and full digital control for high reliability.
  • Robust Construction: Designed with a waterproof and interference-resistant aluminum shell, making it suitable for harsh environments with high temperatures and electromagnetic interference common in flame and plasma cutting.
  • Versatile Interfaces: Easy-to-use interfaces compatible with various CNC systems for flame and plasma cutting, and can also be operated independently.
SF-HC30A3 Torch Height Controller components
Figure 1: Overview of SF-HC30A3 Torch Height Controller and its components.

2. Specifications

Parameter Value
Power Requirement DC 24V ± 2V, 3A
Applicable Motor 17hs (42) series stepper motors
Manual Adjustment Range 0 ~ 100 mm
Automatic Height Control Range 3 ~ 30 mm
Automatic Adjustment Speed 3000 mm/min
Control Accuracy ± 0.5 mm
Box Size (Controller Unit) 155 x 87 x 71 mm
Working Environment Temperature -10 ~ 50 ℃
Detection System Capacitive detector, Arc pressure height detector
Package Dimensions (Approx.) Length: 30 cm, Width: 10 cm, Height: 13 cm
Package Weight (Approx.) 2.8 kg

3. Setup and Installation

Careful installation is crucial for the optimal performance of the SF-HC30A3. Ensure all power is disconnected before beginning installation.

3.1 Component Identification

  • Controller Unit: Main unit with display, buttons, and adjustment knobs.
  • Motor: Stepper motor for torch height adjustment.
  • Mounting Brackets: For securing the controller and torch.
  • Cables: For power, motor, and signal connections.
  • Circuit Board: Internal component for control logic.
Front panel of the SF-HC30A3 controller
Figure 2: Front panel of the SF-HC30A3 controller showing display and controls.
Rear view of the SF-HC30A3 controller with connection ports
Figure 3: Rear view of the SF-HC30A3 controller showing various connection ports.

3.2 Wiring Diagram

Refer to the following wiring diagram for proper connection of the SF-HC30A3 to your CNC system and power supply. Ensure all connections are secure and correctly polarized.

Wiring diagram for the SF-HC30A3 Torch Height Controller
Figure 4: Detailed wiring diagram for the SF-HC30A3 Torch Height Controller. Pay close attention to power input (DC 24V), motor connections, and signal inputs/outputs.

3.3 Mounting

  1. Mount the main controller unit in a location that is easily accessible for operation and away from excessive heat or direct cutting debris.
  2. Securely attach the torch lifting mechanism (actuator) to your cutting machine, ensuring it has a clear vertical path for movement.
  3. Connect the stepper motor to the lifting mechanism and the controller unit.
  4. Ensure all cables are routed safely, away from moving parts and heat sources, and secured to prevent accidental disconnections.

4. Operating Instructions

The SF-HC30A3 controller features a digital display and several knobs for precise control over torch height.

4.1 Front Panel Controls

  • Digital Display: Shows current torch height or other operational parameters.
  • Up/Down Buttons: For manual adjustment of torch height. The manual adjustment range is 0-100 mm.
  • HEIGHT Knob: Adjusts the target cutting height for automatic control. The automatic control range is 3-30 mm.
  • SENSITIVITY Knob: Controls the responsiveness of the automatic height adjustment. Adjust as needed for stable cutting.
  • IHS HEIGHT Knob: Initial Height Sensing adjustment. Sets the initial height before cutting begins.

4.2 Basic Operation

  1. Power On: Ensure all connections are correct, then power on the controller. The digital display should illuminate.
  2. Initial Height Setting (IHS): Use the IHS HEIGHT knob to set the desired initial height. This is the height at which the torch will start before piercing.
  3. Manual Adjustment: Use the Up/Down buttons to manually position the torch if needed.
  4. Automatic Height Control: During cutting, the controller will automatically adjust the torch height based on the arc voltage (for plasma) or capacitive sensing (for flame) to maintain the set HEIGHT.
  5. Sensitivity Adjustment: If the torch height is unstable or too slow to react, adjust the SENSITIVITY knob. A higher sensitivity means faster reaction but can lead to oscillations if too high.

5. Maintenance

The SF-HC30A3 is designed for durability in harsh environments, but regular maintenance will ensure its longevity and consistent performance.

  • Cleaning: Periodically clean the exterior of the controller unit and the torch height sensing components to remove dust, metal particles, and cutting debris. Use a soft, dry cloth. Avoid using harsh chemicals.
  • Connection Checks: Regularly inspect all electrical connections for tightness and signs of wear or corrosion. Loose connections can lead to intermittent operation or damage.
  • Cable Inspection: Check all cables for cuts, abrasions, or kinks. Replace damaged cables immediately.
  • Motor Inspection: Ensure the stepper motor operates smoothly and quietly. Listen for unusual noises that might indicate wear.
  • Environmental Protection: While the unit is robust, avoid exposing it to excessive moisture or extreme temperatures beyond its specified operating range (-10 ~ 50 ℃).

6. Troubleshooting

This section provides solutions to common issues you might encounter with your SF-HC30A3 controller.

Problem Possible Cause Solution
Controller does not power on No power supply; Incorrect wiring; Faulty power supply Check DC 24V power connection; Verify wiring against diagram; Test power supply output.
Torch height not adjusting automatically Sensing system issue; Motor not connected; Incorrect settings; Interference Clean sensing components; Check motor wiring; Adjust HEIGHT and SENSITIVITY knobs; Check for strong electromagnetic interference.
Torch height oscillates or is unstable Sensitivity too high; Mechanical binding; Excessive vibration Reduce SENSITIVITY; Inspect lifting mechanism for smooth movement; Reduce machine vibration.
Manual adjustment not working Motor not connected; Faulty buttons; Internal error Check motor wiring; Contact support if buttons are unresponsive.

If you encounter issues not listed here or if the suggested solutions do not resolve the problem, please contact technical support.

7. User Tips

No specific user tips were available from reviews or Q&A at this time. However, general best practices for torch height controllers include:

  • Always perform a dry run without cutting to verify torch movement and height sensing.
  • Start with lower sensitivity settings and gradually increase if faster response is needed, to avoid oscillations.
  • Ensure your cutting surface is clean and free of obstructions that could interfere with height sensing.
  • Regularly check the torch consumables (nozzle, electrode) as their wear can affect arc voltage and thus automatic height control.

8. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the TECNR Official Store or your authorized dealer. Provide your product model (SF-HC30A3) and any relevant purchase details when seeking assistance.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.