GEYA GRV8-02

Contents

GEYA GRV8-02 Voltage Monitor Device

Over-voltage and Under-voltage Protection Relay Instruction Manual

1. General Information

The GEYA GRV8-02 is a voltage monitoring device designed to protect electrical equipment and motors from damage due to abnormal voltage conditions. It provides comprehensive protection against both over-voltage and under-voltage scenarios.

Applications:

  • Protection of electrical equipment and motors from over-voltage and under-voltage.
  • Normal/emergency power supply switching.

Function Features:

  • Controls its own supply voltage (True RMS measurement).
  • User may select operation mode through knob.
  • Voltage measurement accuracy <1%.
  • Relay status is indicated by LED.
  • 1-MODULE, DIN rail mounting.

Model GRV8-02:

This specific model, GRV8-02, offers combined over-voltage and under-voltage protection. For applications requiring separate over-voltage or under-voltage monitoring, please refer to the GRV8-01 model.

Technical Parameter Diagram showing GRV8-01 and GRV8-02 models with their respective control knobs and indicators.
Figure 1: GRV8-01 and GRV8-02 Technical Parameter Overview

2. Safety Information

Please read and understand all safety instructions before installation and operation to prevent injury or damage to the device and connected equipment.

  • Installation: This product must be installed by qualified electricians. All electrical connections must comply with the appropriate local and international safety standards.
  • Voltage: The device is designed for low voltage applications, typically below 50Vac or 75Vdc, as per EU LVD Voltage directives.
  • Disposal: All electrical waste should be disposed of in compliance with current WEEE (Waste Electrical and Electronic Equipment) regulations.

3. Setup

3.1. Mounting

The GEYA GRV8-02 is designed for easy installation on a standard DIN rail (EN/IEC 60715).

3.2. Wiring Diagram

Ensure correct wiring according to the diagram below. Incorrect wiring can lead to malfunction or damage.

Wiring Diagram, Panel Diagram, and Functions Diagram for GRV8-01 and GRV8-02 relays.
Figure 2: Wiring Diagram (Top Left)
  • Supply/Monitoring Terminals: A1 and A2
  • Output Contact Terminals (1SPDT): 11, 12, 14

3.3. Cable Connection

  • Max. Cable Size: Solid wire max. 1x2.5 mm² or 2x1.5 mm²; with sleeve max. 1x2.5 mm² (AWG 12).
  • Tightening Torque: Ensure terminal screws are tightened to 0.8 Nm.

3.4. Panel Controls

The front panel features several controls and indicators for configuration and status monitoring:

Top view of the GRV8-02 relay showing the A1 and A2 terminals.
Figure 3: GRV8-02 Top View with Terminals
Front view of the GEYA GRV8-02 Voltage Monitor Device showing control knobs and LED indicators.
Figure 4: GRV8-02 Front Panel Controls
  • Un (Green LED): Supply Indication. Illuminates when power is supplied to the device.
  • R (Red LED): Relay Status Indication. Illuminates when the output relay is active.
  • U> Knob: Overvoltage threshold setting. Adjust to set the upper voltage limit.
  • U< Knob: Undervoltage threshold setting. Adjust to set the lower voltage limit.
  • H Knob: Hysteresis setting. For GRV8-02, this is fixed at 3%.
  • T Knob: Adjustable Time Delay (0.1s-10s). Sets the delay before tripping or resetting.
  • AC/DC Switch: Selects between AC or DC operation mode.

4. Operation

4.1. Power On

Upon applying power to terminals A1-A2, the green 'Un' LED will illuminate, indicating the device is powered. There is a run-up delay of 0.5 seconds before monitoring begins.

4.2. Setting Protection Parameters

  1. Select Power Source: Use the AC/DC switch to match your supply voltage type.
  2. Set Over-voltage Threshold (U>): Rotate the 'U>' knob to the desired over-voltage trip level.
  3. Set Under-voltage Threshold (U<): Rotate the 'U<' knob to the desired under-voltage trip level.
  4. Set Time Delay (T): Adjust the 'T' knob to set the desired time delay (0.1s-10s). This delay prevents nuisance tripping from momentary voltage fluctuations.

4.3. Relay Response

  • Over-voltage Trip: If the monitored voltage exceeds the 'U>' threshold for the set time delay, the relay will trip, and the red 'R' LED will change state (e.g., turn off if normally on, or turn on if normally off).
  • Under-voltage Trip: If the monitored voltage drops below the 'U<' threshold for the set time delay, the relay will trip, and the red 'R' LED will change state.
  • Automatic Reset: The GRV8-02 features an automatic reset function with a reset time of 1000ms. Once the voltage returns to the safe operating range (considering the 3% fixed hysteresis), the relay will automatically reset after this delay.

4.4. Operation Demonstration Video

Watch this video for a visual demonstration of the over-voltage and under-voltage trip conditions and the relay's response.

Video 1: Single Phase Voltage Monitoring Relay Function Demonstration

5. Technical Specifications

The following table details the technical parameters for the GRV8-01 and GRV8-02 models.

Table of Technical Parameters for GRV8-01 and GRV8-02 models.
Figure 5: Technical Parameters Table
GRV8-02 Technical Parameters
ParameterSpecification (GRV8-02)
FunctionMonitoring voltage
Supply terminalsA1-A2
Rated supply voltageDC12V, AC/DC24-48V, AC/DC110-240V, AC220V
Rated supply frequency45Hz-65Hz, 0
Hysteresis3% fixed
Supply indicationGreen LED
Time delayAdjustable 0.1s-10s, 10%
Measurement error≤1%
Run up delay at power up0.5s time delay
Knob setting accuracy10% of scale value
Reset time1000ms
Temperature coefficient0.05% /℃, at=20℃ (0.05%℉, at=68℉)
Output1×SPDT
Current rating10A/AC1
Switching voltage250VAC/24VDC
Min. breaking capacity DC500mW
Output indicationRed LED
Mechanical life1×107
Electrical life (AC1)1×105
Operating temperature-20℃ to +55℃ (-4℉ to 131℉)
Storage temperature-35℃ to +75℃ (-22℉ to 158℉)
Mounting/DIN railDin rail EN/IEC 60715
Protection degreeIP40 for front panel/IP20 terminals
Operating positionAny
Overvoltage categoryIII.
Pollution degree2
Max. cable size (mm²)Solid wire max. 1x2.5 or 2x1.5 / with sleeve max. 1x2.5 (AWG 12)
Dimensions90×18×64mm
Weight59g
StandardsEN 60255-1, IEC60947-5-1

6. Troubleshooting

6.1. LEDs Flashing (Un and R simultaneously)

If both the green 'Un' LED and the red 'R' LED are flashing simultaneously, this indicates a setting error. For the GRV8-02, this typically occurs if the overvoltage threshold (U>) is set to be less than or equal to the undervoltage threshold (U<).

  • Solution: Correct the voltage threshold settings to ensure U> is always greater than U<. After adjusting, power cycle the device to resume normal operation. In this error state, the output relay will be disconnected.

6.2. Relay Not Tripping or Resetting as Expected

  • Check Threshold Settings: Verify that the 'U>' and 'U<' knobs are set to appropriate voltage levels for your application.
  • Verify Time Delay: Ensure the 'T' knob is set to the desired time delay. The relay will only trip or reset after this delay has elapsed.
  • Understand Hysteresis: Remember that the GRV8-02 has a fixed 3% hysteresis. The voltage must return to a level 3% within the safe operating range before the relay will reset.
  • Confirm Power Supply: Ensure the power supply connected to A1-A2 is stable and within the rated voltage range for your specific GRV8-02 model.

6.3. No Power Indication (Green Un LED off)

  • Check Connections: Verify that the power supply connections to terminals A1-A2 are secure and correct.
  • Power Source: Ensure the power source itself is active and providing the correct voltage.

7. User Tips

  • Coil Voltage Awareness: Depending on the specific model variant, the internal relay coil might be powered by 24V. Always double-check the rated supply voltage of your GRV8-02 unit before making any connections to avoid damage.
  • Automatic Recovery: The GRV8-02 is designed for automatic recovery. If a voltage anomaly (over or under) causes a trip, the relay will automatically reset after a 1000ms delay once the voltage returns to the safe operating range (considering the 3% hysteresis).
  • 220V Operation: The GRV8-02 is available in an AC220V variant, providing reliable over-voltage and under-voltage protection for 220V AC systems. Ensure you select the correct model for your specific supply voltage.
  • Detailed Manual: For more in-depth information, including detailed function diagrams and specific application examples, please refer to the official user manual PDF available from the manufacturer.

8. Warranty & Support

8.1. Certifications

The GEYA GRV8-02 Voltage Monitor Device is compliant with international safety and environmental standards, holding CE, RoHS, and CB certifications.

8.2. Manufacturer Information

GEYA ELECTRICAL CO.,LTD
Address: Wenzhou Bridge Industrial Zone, Beibaixiang Town, Yueqing, Zhejiang, China 325603
Mobile: 0086-13567770207
E-mail: sale@cngeya.com
Website: www.geya.net

GEYA company information including establishment year, annual turnover, headquarters, product categories, and certifications.
Figure 6: GEYA Company Information and Certifications

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.