FLIPSKY FSESC6.7 Plus

Contents

FLIPSKY Dual FSESC6.7 Plus Electric Skateboard ESC

User Instruction Manual

1. Product Overview

The FLIPSKY Dual FSESC6.7 Plus is an advanced Electric Speed Controller (ESC) designed for electric longboards and skateboards. Featuring a durable aluminum case and based on the VESC6 platform, this dual ESC provides robust power management for 3S to 12S LiPo battery setups, supporting continuous currents up to 200A (total) and instantaneous currents up to 800A (total). It includes a Pro switch for easy power control and a Can bus connector for convenient 4WD configurations.

Front view of the Dual FSESC6.7 Plus with aluminum case and connected wires.
Front view of the Dual FSESC6.7 Plus with aluminum case and connected wires.
Rear view of the Dual FSESC6.7 Plus.
Rear view of the Dual FSESC6.7 Plus.
Top view of the Dual FSESC6.7 Plus with button and multiple antenna ports.
Top view of the Dual FSESC6.7 Plus with button and multiple antenna ports.

2. Key Features

  • Pro Switch Version: Power on/off functionality by pressing the integrated button.
  • Can Bus Connector: Facilitates convenient setup for 4WD (four-wheel drive) configurations.
  • Enhanced Manufacturing: USB port utilizes SMT (Surface-Mount Technology) soldering for improved reliability.
  • Optimized Design: Features SMT mounting capacitors and additional MOSFETs on the bottom side for better performance and heat management.
  • Durable Construction: Housed in a robust aluminum case for protection and efficient heat dissipation.

3. Specifications

FeatureDetail
Hardware VersionV 6.6
Firmware VersionLatest firmware version
Voltage Range8V - 60V (Safe for 3S to 12S LiPo). Voltage spikes must not exceed 60V.
Continuous Current100A per single ESC, 200A total.
Instantaneous Current400A per single ESC, 800A total for the system. (Values depend on mounting and ambient temperature.)
5V Output1.5A for external electronics (per single ESC)
3.3V Output1A for external electronics (per single ESC)
Supported ModesDC, BLDC, FOC (sinusoidal)
Supported SensorsABI, HALL, AS5047
ERPM150,000
Dimensions (LWH)78 x 78 x 20mm (including heatsink)
Motor Wire Gauge12AWG
Power Cable Gauge8AWG
Recommended Connectors4MM Bullet Connector
Battery Voltage Tolerance+/-0.6V
Dimensional drawing of the Dual FSESC6.7 Plus, showing length, width, and height.
Dimensional drawing of the Dual FSESC6.7 Plus, showing length, width, and height.
Close-up view of the Dual FSESC6.7 Plus circuit board, highlighting capacitors and their specifications (100uF/63V, 150uF/80V).
Close-up view of the Dual FSESC6.7 Plus circuit board, highlighting capacitors and their specifications (100uF/63V, 150uF/80V).
Diagram showing wire sizes (8AWG for power, 12AWG for motor) and component layout on the Dual FSESC6.7 Plus.
Diagram showing wire sizes (8AWG for power, 12AWG for motor) and component layout on the Dual FSESC6.7 Plus.

4. Package Contents

The standard shipping package for the Dual FSESC6.7 Plus includes:

  • 1 x Dual FSESC6.7 Plus with Heatsink
  • 2 x VESC Sensor Wires
  • 1 x LED Button
  • 1 x Micro USB Cable
  • 1 x User Manual
Contents of the Dual FSESC6.7 Plus package, including the ESC, sensor wires, LED button, and USB cable.
Contents of the Dual FSESC6.7 Plus package.

5. Setup & Installation

Important Safety Note: Please do not remove the shrink wrap protecting the PCB electronic components. This prevents impurities or metals from causing short circuits or ESC damage.

5.1. General Wiring Diagram

Detailed wiring diagram for connecting two motors, battery, and power button to the Dual FSESC6.7 Plus.
Detailed wiring diagram for connecting two motors, battery, and power button.

This diagram illustrates the primary connections for your Dual FSESC6.7 Plus:

  • Battery Connection: Connect your battery pack to the main power input (red and black thick wires). Ensure correct polarity.
  • Motor Connections: Connect your two motors to the designated motor outputs (black wires). If your motors have hall sensors, connect the VESC Sensor Wires to the corresponding sensor ports on the ESC and motors.
  • Power Button: Connect the included LED button to the designated button port.
  • CAN Bus Connector: Use this port to connect multiple ESCs for 4WD setups.
  • PPM+UART: Connect your receiver for throttle control and communication.

5.2. ADC Throttle Wiring

Wiring diagram illustrating connection of an ADC throttle to the Dual FSESC6.7 Plus.
Wiring diagram for connecting an ADC throttle.

For ADC throttle control, connect the throttle to the ADC port on the ESC, ensuring the 3.3V, GND, and ADC signal lines are correctly aligned.

5.3. Pinout Diagram

Pinout diagram for the Dual FSESC6.7 Plus, detailing connections for button, USB, CAN, PPM+UART, Sense, and Comm ports.
Pinout diagram for the Dual FSESC6.7 Plus.

Refer to the pinout diagram for detailed identification of all connection points, including USB1, USB2, Sense1, Sense2, CAN, Comm1, Comm2, and PPM+UART ports.

6. Operating Instructions

  • Power On/Off: Press the integrated LED button to power the ESC on or off.
  • Configuration: Use the Micro USB cable to connect the ESC to a computer for configuration via VESC tool software. Ensure you are using the latest firmware version.
  • Motor Control: The ESC supports DC, BLDC, and FOC (sinusoidal) motor control modes. Select the appropriate mode for your motors during configuration.
  • 4WD Setup: For multi-motor setups, utilize the CAN bus connector to synchronize multiple ESCs.

7. Maintenance

  • Protection: Keep the original shrink wrap on the PCB to protect electronic components from impurities, dust, and metal particles that could cause short circuits.
  • Cleaning: Regularly inspect the ESC for dirt or debris. Clean gently with a dry, soft brush or compressed air. Avoid using liquids.
  • Environmental Conditions: Operate and store the ESC in a dry environment, away from moisture and extreme temperatures.
  • Connection Integrity: Periodically check all wire connections for tightness and signs of wear. Replace any damaged wires or connectors immediately.
  • Firmware Updates: Keep the ESC firmware updated to the latest version for optimal performance and bug fixes.
Overview of the Dual FSESC6.6 Plus, highlighting key components and specifications.

8. Troubleshooting

  • No Power: Ensure the battery is charged and correctly connected. Check the power button connection.
  • Motor Not Spinning: Verify motor connections and sensor wires (if used). Check VESC tool settings for motor detection and configuration.
  • Intermittent Operation: Inspect all wiring for loose connections or damage. Ensure the ESC is not overheating.
  • Connection Issues (USB/CAN): Confirm USB cable integrity and proper driver installation. For CAN bus, ensure all ESCs are correctly wired and configured.
  • Overheating: Ensure adequate airflow around the ESC. Reduce continuous current draw if possible. The aluminum case and internal heat transfer pads are designed for heat dissipation, but extreme conditions may require additional cooling.

If you encounter persistent issues, consult online VESC communities or contact FLIPSKY support for assistance.

9. User Tips

  • Durable Construction: The ESC features a robust aluminum case, providing excellent protection and heat dissipation.
  • 4WD Integration: For multi-motor setups, leverage the integrated Can bus connector for seamless communication between ESCs.
  • Connector Check: While the product is well-made, always ensure you have all necessary connectors for your specific setup, as some may need to be acquired separately.

10. Warranty & Support

10.1. Warranty Policy

The warranty period for consumable electronic products (e.g., VESC/Motor/Battery) is 2 months, starting from the 7th day after shipment (the shipping date is checked by logistic record). For non-electronic products, the warranty period is also 2 months from the 7th day after shipment.

Warranty will be voided under the following conditions:

  • Mechanical damage to electronic components or PCB.
  • PCB board has repair soldering iron traces (excluding soldering the cable bullet connectors).
  • Water damage or external impact damage.
  • Any abnormal applications beyond the product specifications.

Most products are tested and shipped as good products. If you have any questions regarding VESC/Motor settings or connections, please contact us before installation.

FLIPSKY's liability will not exceed the actual purchase price of the product.

10.2. Repair Service

FLIPSKY is willing to provide repair service for a reasonable charge if your product is out of warranty. This service includes both sides' shipping costs.

10.3. Contact Support

For any support inquiries, please contact FLIPSKY via email: flipskytech@outlook.com.

11. Safety Information

⚠️ Warning: Protective equipment should be worn. Not to be used in traffic.

  • Always wear appropriate safety gear, including a helmet, knee pads, and elbow pads, when operating an electric skateboard.
  • Ensure all electrical connections are secure and insulated to prevent short circuits.
  • Do not operate the electric skateboard in wet conditions or near water.
  • Regularly inspect your equipment for any signs of damage or wear before each use.
  • Keep hands and loose clothing away from moving parts.
  • Always be aware of your surroundings and ride responsibly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.