HLTNC STB5100 MPG

Contents

HLTNC STB5100 Mach3 USB 5-Axis CNC Motion Controller Card and MPG Handwheel User Manual

Model: STB5100 MPG | Brand: HLTNC

1. Introduction

This manual provides detailed instructions for the installation, setup, operation, and maintenance of your HLTNC STB5100 Mach3 USB 5-Axis CNC Motion Controller Card and MPG Handwheel. Please read this manual thoroughly before using the product to ensure safe and efficient operation.

1.1 Safety Warnings

The motion control card is designed for machine control and requires professional expertise for proper use. Improper use may lead to accidents. Please strictly follow all instructions and warnings. If you are unsure about any aspect of this product, consult with engineers for assistance.

For first-time users or those unfamiliar with the product and Mach3 software features, always ensure the machine's power switch is within reach to quickly turn off power during testing. It is highly recommended to install an emergency stop button and verify its proper function. Failure to adhere to these instructions and warnings may result in direct or indirect personal injury, for which our company does not assume responsibility.

2. Package Contents

Please verify that all items listed below are included in your package:

  • 1 x 5-Axis USB Port Motion Controller Card
  • 1 x 6-Axis MPG Handwheel with Emergency Stop Button
  • 1 x USB Cable
HLTNC STB5100 Motion Controller Card and MPG Handwheel
Image 2.1: Package contents including the controller card, handwheel, and USB cable.

3. Features

  • Supports Windows XP, Windows 7 (32/64bit), Windows 8, and Windows 10 operating systems.
  • Compatible with all versions of Mach3 software.
  • Supports 5-Axis CNC control, capable of connecting five stepper motor drivers or servo drivers.
  • Maximum output pulse frequency of 100KHz, with automatic pulse width adjustment for closed-loop drivers.
  • Five optocoupler isolated input signal interfaces for limit switch, emergency stop switch, auto tool zero sensor, and home switch (NPN sensor switch compatible).
  • Inverter control signal interface with optocoupler isolation: Provides 0-10V speed control signal, PWM speed control signal, and spindle start control signal for Mach3 software to manage spindle speed, start, and stop.
  • Four universal output signal interfaces (maximum 500mA current) to drive relays, solenoid valves, mist, pumps, cylinders, and other equipment.
  • Supports external electronic handwheel connection via HDR15 interface for manual machine tool control.
  • Includes an enable signal interface for controlling the driver enable signal.
  • Control card power requirement: 12-24VDC, current greater than 500MA.

4. Specifications

4.1 General Specifications

AttributeValue
Brand NameHLTNC
Model NumberSTB5100 MPG
OriginMainland China
Motor TypeStepper Motor
CertificationCE, NONE
Controller CardMach3 USB 5 Axis
Pulse100
Voltage5V
Handwheel FeaturesWith Emergency Stop Button
Wireless FunctionalityNo
Battery IncludedNo
EU LVD VoltageLow voltage: Below 50Vac or 75Vdc
High-concerned chemicalNone

4.2 PCB Mark Description

MarkDescription
+5V+5V Driver signal common
XPX Axis Pulse signal
XDX Axis Direction signal
YPY Axis Pulse signal
YDY Axis Direction signal
ZPZ Axis Pulse signal
ZDZ Axis Direction signal
APA Axis Pulse signal
ADA Axis Direction signal
BPB Axis Pulse signal
BDB Axis Direction signal
ENAll Axis Enable signals
V+Positive power supply 12-24V
V-Negative power supply 0V
FWDInverter Control signal: Start/Forward
AVIInverter Control signal: 0-10V Speed control signal
GNDGND=V-=0V
PWMPWM Signal
COMCOM=V-=GND=0V
I1Input signal interface 1
I2Input signal interface 2
I3Input signal interface 3
I4Input signal interface 4
I5Input signal interface 5
O1Output signal interface 1
O2Output signal interface 2
O3Output signal interface 3
O4Output signal interface 4
12-24V LEDPower input indication LED
PWR LEDUSB power indication LED
MPGMPG Handwheel interface

4.3 Mechanical Dimensions

Mechanical dimensions of the controller card
Image 4.1: Mechanical dimensions of the STB5100 controller card (Dimensions in mm).

5. Setup & Installation

5.1 Mach3 Software Installation Procedure

Follow these steps to install the Mach3 software. A visual guide is also provided in the video below.

  1. Locate the Mach3 software folder and click on it.
  2. Find and execute the Mach3 installer (e.g., "Mach3VersionR3.041instal").
  3. Click "Next" on the welcome screen.
  4. Accept the End User License Agreement by clicking "Yes".
  5. Click "Next" on the Readme Information screen.
  6. Select the destination directory for Mach3 (default is usually fine).
  7. Click "Next" to confirm the program folder.
  8. Click "Next" to start copying files.
  9. If prompted with an "Unable to register component" error, click "OK" or the equivalent button to proceed.
  10. If prompted with another registration error, click "OK" or the equivalent button to proceed.
  11. Click "Finish" once the setup is complete.
  12. If a "DriverTest" window appears, click "OK" or the equivalent button.
  13. Navigate to the "Mach3Plugin" folder.
  14. Open the "Plugins" subfolder.
  15. Copy the files "BL-UsbMach.dll" and "RnRMotion.dll".
  16. Paste these two files into the "Plugins" folder within your Mach3 installation directory (e.g., C:\Mach3\Plugins).
  17. Open the Mach3Mill shortcut on your desktop to launch the software.
Video 5.1: Step-by-step guide for Mach3 software installation.

5.2 Hardware Connection Overview

The following diagram provides an overview of the basic connections for the STB5100 motion controller card. Ensure all connections are secure and correctly aligned.

Basic connection diagram for STB5100
Image 5.2: Basic connection diagram showing inputs, outputs, power, and USB connection points.

Key connection points:

  • Power Supply: Connect a 12-24VDC power source (current > 0.5A) to the designated terminals.
  • USB Connection: Connect the controller card to your computer via the USB port.
  • MPG Handwheel: Connect the MPG handwheel to the HDR15 interface.
  • Input Channels: 5 input channels for E-stop, limit switches, probe, home switches, etc.
  • Output Channels: 4 output channels for controlling mist/flood, relays, solenoid valves, etc.
  • Spindle Inverter: Connect for 0-10V/FWD/PWM signals to control spindle speed and direction.
  • Driver Signal Interfaces: Connect to your stepper or servo motor drivers.

5.3 MPG Handwheel Wiring

The electronic handwheel connects via an HDR15 interface. The pin definitions are crucial for correct wiring. You can either wire your own connector according to the table below or use a pre-wired handwheel.

Electronic handwheel wiring table
Image 5.3: Electronic handwheel wiring table for the HDR15 connector.

Note: The handwheel does not directly control motor operation; it sends signals to the software, which then controls the motors. Rotating the handwheel will change the software coordinates.

For a more detailed wiring diagram of the controller card, refer to the image below:

Detailed wiring diagram of the STB5100 controller card
Image 5.4: Detailed wiring diagram for the STB5100 controller card, showing input/output terminals and voltage outputs.

6. Operating Instructions

6.1 Verifying Connection to Software

Once the motion control card is successfully connected to your computer and Mach3 software, a prompt indicating "UsbMach connected" will appear in the Mach3 status bar.

Mach3 status bar showing UsbMach connected
Image 6.1: Mach3 status bar indicating a successful connection to the UsbMach controller.

6.2 Using the Mach3 "Reset" Button

If the "Reset" button in Mach3 is flashing, the software will not function. If you are unable to reset it, please check your motion control card's connection and software input settings. Click the "Reset" button to clear any active emergency stop or error states.

Mach3 interface with Reset button and MPG controls
Image 6.2: Mach3 interface showing the Reset button and MPG control panel.

6.3 Activating the MPG Interface

To bring up the MPG (Manual Pulse Generator) interface in Mach3, press the "Tab" button on your keyboard. Once the interface appears, you can click on the individual axis buttons (X, Y, Z, A, B, C) to manually control the motor movement.

7. Maintenance

  • Cleaning: Regularly clean the controller card and handwheel with a soft, dry cloth. Avoid using liquid cleaners or solvents.
  • Environment: Store and operate the device in a dry, dust-free environment. Avoid extreme temperatures and humidity.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.
  • Software Updates: Keep your Mach3 software updated to the latest stable version for optimal performance and compatibility.

8. Troubleshooting

  • "No UsbMachBoard, Please plug it in!" error: This indicates the controller card is not detected. Ensure the USB cable is securely connected to both the card and your computer. Try a different USB port or cable. Verify that the Mach3 plugin files are correctly copied to the Mach3 installation directory's "Plugins" folder.
  • Flashing "Reset" button in Mach3: This means the system is in an emergency stop or error state. Click the "Reset" button in Mach3. If it continues to flash, check all emergency stop switches, limit switches, and their wiring for proper function. Review your Mach3 input settings.
  • Motors not responding: Verify that the controller card is powered on (12-24VDC) and the PWR LED is illuminated. Check all wiring to the motor drivers and motors. Ensure the Mach3 software is connected and not in a "Reset" state.
  • Handwheel not controlling movement: Ensure the handwheel is correctly wired to the HDR15 interface as per the wiring diagram. Verify that the MPG interface is active in Mach3 (press "Tab") and the correct axis is selected.

For more detailed troubleshooting steps, please refer to the official user manual PDF available from the seller: User manual (PDF).

9. User Tips

  • Gradual Axis Connection: If you are new to Mach3 and motion control cards, it is advisable to connect and test one axis at a time. Once that axis functions correctly, proceed to connect and test the other axes.
  • Wiring Diagrams: Pay close attention to the provided wiring diagrams for the handwheel and controller card. While a basic sheet with color correspondence may be included, detailed connection diagrams for specific connectors (like DB15 or DB21) are essential for proper setup.
  • Manual Availability: Always check for the latest version of the user manual, especially if the included documentation is not in your preferred language. Online resources or contacting the seller may provide updated or translated versions.

10. Warranty & Support

For warranty information and technical support, please contact the seller directly. Keep your purchase records for any warranty claims. Additional resources, including a detailed user manual, may be available in PDF format from the seller.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.