diymore MIDI Shield

Contents

diymore MIDI Shield for Arduino User Manual

Musical Instrument Digital Interface Adapter Plate for Arduino and Microcontrollers

Introduction

The MIDI Shield is designed to provide an easy interface for Arduino boards and other microcontrollers to communicate using the Musical Instrument Digital Interface (MIDI) protocol. This shield simplifies the integration of MIDI functionality into your electronic projects, enabling interaction with musical instruments and other MIDI-compatible devices.

The MIDI protocol shares many similarities with asynchronous serial communication, allowing microcontrollers to send and receive MIDI event information via their UART (Universal Asynchronous Receiver/Transmitter) pins.

Top view of the diymore MIDI Shield for Arduino, showing MIDI IN, OUT, and THRU ports, a RUN/PGM switch, and pin headers.
Figure 1: Top view of the MIDI Shield module.

Setup Instructions

  1. Physical Connection: The MIDI Shield is designed to be installed directly as a shield on top of an Arduino board. Carefully align the male header pins on the shield with the female header sockets on your Arduino board. Ensure proper alignment before gently pressing the shield into place.
  2. MIDI Port Connections:
    • Connect the MIDI IN/THRU pins of the shield to the hardware RX (Receive) pin of your Arduino board.
    • Connect the MIDI OUT pin of the shield to the hardware TX (Transmit) pin of your Arduino board.
    Refer to your specific Arduino board's documentation for the exact RX/TX pin assignments. The MIDI IN port features opto-isolation to prevent ground loops, ensuring clean signal transmission.
  3. MIDI Connectors: Note that the three-hole MIDI connectors are typically included with the product but may require soldering onto the adapter plate if not pre-assembled.
Detailed top view of the MIDI Shield showing MIDI IN, OUT, THRU labels, the RUN/PGM switch, and pin headers for Arduino connection.
Figure 2: Pin and port identification on the MIDI Shield.

Operating Instructions

Once connected, your Arduino board can send and receive MIDI messages. The MIDI IN port receives data from external MIDI devices, the MIDI OUT port transmits data from your Arduino to other MIDI devices, and the MIDI THRU port re-transmits data received at the MIDI IN port, allowing for daisy-chaining of multiple MIDI devices without signal degradation.

The RUN/PGM switch on the board allows for convenient programming of your Arduino. When uploading new code to your Arduino board, ensure this switch is set to 'PGM' (Program). After the code has been successfully uploaded, switch it to 'RUN' for normal operation of your MIDI application. This feature eliminates the need to physically remove the shield every time you program your Arduino.

The data and analog pins, as well as power and ground buses, are typically broken out on the shield, allowing for further expansion and connection of other components to your Arduino project.

Angled view of the MIDI Shield, highlighting the MIDI IN, OUT, and THRU ports and the compact design.
Figure 3: Angled view of the MIDI Shield, showing the MIDI ports.

Specifications

Feature Detail
Dimensions 57.4 x 53.1 mm
Interface Type MIDI (Musical Instrument Digital Interface)
Connections MIDI IN, MIDI OUT, MIDI THRU
Input Isolation Opto-isolated MIDI IN to prevent ground loops
Compatibility Designed for Arduino boards and other microcontrollers with UART
Programming Switch RUN/PGM switch for easy Arduino programming
Package Type SOP (Small Outline Package)
Application Computer/Microcontroller interfacing
Module Type Adapter Module
Origin Mainland China
Condition New
Operating Temperature -20°C to 65°C
Approximate Weight 0.038 kg
Bottom view of the diymore MIDI Shield, showing solder points and circuit traces.
Figure 4: Bottom view of the MIDI Shield.

Troubleshooting

  • No MIDI Communication:
    • Verify that the MIDI IN/THRU and MIDI OUT pins are correctly connected to the Arduino's RX and TX pins, respectively.
    • Ensure the RUN/PGM switch is set to 'RUN' during operation.
    • Check your Arduino code for correct MIDI library usage and serial communication settings (e.g., baud rate).
    • Confirm that external MIDI devices are properly connected and powered.
  • Programming Issues:
    • Ensure the RUN/PGM switch is set to 'PGM' when attempting to upload code to your Arduino.
  • Ground Loop Noise:
    • The MIDI IN port is opto-isolated to prevent ground loops. If you experience noise, ensure all ground connections are stable and correctly wired.

User Tips

No specific user tips were available from provided reviews or Q&A for this product.

Maintenance

The MIDI Shield is a robust electronic component and generally requires minimal maintenance. To ensure longevity and optimal performance:

  • Keep the board clean and free from dust, debris, and moisture.
  • Avoid exposing the module to extreme temperatures or sudden physical shock.
  • Periodically inspect solder joints for any signs of damage or corrosion, especially if the board is used in environments with high vibration or humidity.

Warranty and Support

For technical support, additional documentation, or software libraries, please refer to the official resources provided by the manufacturer or the Arduino community. A user manual in PDF format may be available at this link.

Warranty information is typically provided by the seller at the time of purchase. Please retain your proof of purchase for any warranty claims or support inquiries.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.