Important Safety Information
WARNING:
- Always follow instructions provided in manuals when installing. Use only genuine SHIMANO parts. Incorrect assembly or adjustment can lead to component failure and loss of control.
- Wear approved eye protection during maintenance tasks.
- Clean the chain and QUICK-LINK regularly with an appropriate chain cleaner. Avoid alkali- or acid-based solvents, which can cause serious injury if the chain breaks.
- Check the chain for damage (deformation, cracking), skipping, or other abnormalities. Consult a professional if problems are found.
CAUTION:
- Do not allow the wheel to turn while securing the inner cable and installing the inner end cap to prevent injury.
NOTICE:
- For SHADOW RD+, ensure the plate unit cover and rubber cap are installed before riding.
- If gear shifting is not smooth, consult your place of purchase.
- Periodically wash and lubricate gears, chain, and QUICK-LINK with neutral detergent to extend life.
- Products are not guaranteed against natural wear and deterioration.
- SHIMANO lubricants and maintenance products are highly recommended.
- Ensure the rear derailleur does not interfere with the chainstay; adjust the B-screw if necessary.
- Grease the inner cable and sliding portions of the outer casing with SIS SP41 Grease (Y04180000) for smooth operation.
- Use an OT-SP41 outer casing and cable guide.
- Ensure outer casing has enough slack when handlebars are turned fully.
- Periodically clean the shifting unit and lubricate all moving parts.
- Note the installation direction of pulleys; some models have arrows indicating counterclockwise rotation.
- Replace pulleys if abnormal noise due to excess play occurs.
- Check compatibility information for LINKGLIDE products at https://productinfo.shimano.com/#/com.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | SHIMANO |
| Model Numbers | M4000/M3100 |
| Derailleur Groupset Type | Mechanical Derailleur system |
| Type | Rear Derailleur |
| Material | Alloy |
| Gears | 9 Speed |
| Total Capacity | 45T (Max), 11t (Pulley Teeth) |
| Max. Low Sprocket | 36T |
| Compatible Chain | HG 9-speed |
| Pulley Cage | SGS |
| Package Dimensions | 13 cm (Length) x 8 cm (Width) x 5 cm (Height) |
| Package Weight | 0.4 kg |
Product Images








Tools Required
The following tools are needed for installation, removal, adjustment, and maintenance:
- 2 mm hexagon wrench
- 3 mm hexagon wrench
- 4 mm hexagon wrench
- 5 mm hexagon wrench
- Cross head screwdriver [#2]
- Hexalobular [#27]
- TL-CT12 (Cable Cutter)
Setup: Installation and Removal
Installing the Rear Derailleur
Set the switch lever in the OFF position.
Locate the switch lever on the derailleur body and move it to the OFF position. This is typically indicated by an arrow pointing to 'OFF'.
Tighten the rear derailleur mounting screw.
Ensure the derailleur hanger is straight. Use a 5 mm hexagon wrench to tighten the mounting screw to 8-10 N·m. Install the rear derailleur so that the stopper plate contacts the B-tension stop without any gap. Periodically check for any gap between these parts, as it can affect gear shifting performance.
Installing the Chain
Refer to the dealer's manual for specific instructions on installing/removing the chain. Ensure the chain is passed through the main body of the rear derailleur from the side of the chain derailment prevention plate. Incorrect routing can cause damage.
Operating: Adjustment
Adjusting the Stroke on the High Limit
Adjust by turning the high limit screw.
Adjust the high limit screw (marked 'H' or '2' on some models) so that the center of the guide pulley is aligned with the outer face of the smallest sprocket when viewed from the rear side.
Checking the Chain Length
Mount the chain on the largest sprocket and the largest chainring.
To check the length, join the two ends of the chain at the rear of the cassette. The proper final chain length is determined by adding a certain amount of links to this length, depending on the bike type.
- Hardtail bikes: 4 to 5 links + a QUICK-LINK, or 5 to 6 links + a connecting pin.
- Full suspension bikes: Check chain length with suspension in its fully extended position. 5 to 6 links + a QUICK-LINK, or 6 to 7 links + a connecting pin.
If the chain length is too short, drivetrain components may be damaged due to excessive load.
Connection and Securing of the Inner Cable
Loosen the B-screw.
Loosen the B-screw until the stopper plate touches the bracket body without a gap.
Determine the length of the outer casing.
Attach a sealed outer cap to the end of the outer casing. Align the end of the outer cap to the bottom edge of the outer casing holder on the rear derailleur. Ensure enough slack in the outer casing, especially considering rear suspension travel. For extreme derailleur motion, an aluminum type sealed outer cap is recommended.
Cut off any excess outer casing.
Use a cable cutter (TL-CT12) to cut excess outer casing. After cutting, ensure the outside of the outer casing is a perfect circle and the inside of the hole has a uniform shape.
Install the sealed outer cap.
Route the inner cable through the outer casing and install the sealed outer cap to its end. If applicable, install the sealed outer cap with tongue and rubber shield onto the outer casing stopper of the frame.
Set the shift lever to its initial position.
Operate the release lever 9 or more times for a 10-speed system (or 10+ for 11-speed, 11+ for 12-speed).
Secure the inner cable to the rear derailleur.
For RD-M9100 / RD-M9120, replacing the cover with tongue is recommended when replacing the inner cable. Cables with polymer coating may appear fuzzy, but performance is not affected if installed correctly. Secure the inner cable to the rear derailleur, ensuring it is in the cable fixing groove. Tighten to 6-7 N·m.
Remove initial slack from the inner cable.
Hold the rear derailleur to prevent movement under load. Operate the shift lever several times to tension the cable assembly.
Re-secure the inner cable to the rear derailleur.
While pulling the inner cable, ensure it is securely in the cable fixing groove. Tighten to 6-7 N·m.
Cut the inner cable and install the inner end cap.
Cut the inner cable so the protruding length is approximately 20 mm. Install the inner end cap. Check that the inner cable does not interfere with the spokes of the wheel.
Adjusting the Stroke on the Low Limit
Adjust by turning the low limit screw.
Adjust the low limit screw (marked 'L' or '2' on some models) so that the center of the guide pulley is aligned with the center of the largest sprocket.
Adjusting the B-screw
Shift the chain to the smallest chainring and the largest sprocket.
Turn the crank arm and shift the gears.
Adjust the B-screw.
Adjust based on the product combination. For example, align the line on the inner side of the outer plate with the tip of the highest tooth on the largest sprocket (for RD-M9100-GS, RD-M8100-GS, RD-M5130-GS, RD-M5100-SGS). For other models, align the contour of the outer plate and the tip of the highest tooth on the largest sprocket between the arrows on the inner side of the outer plate.
SIS Adjustment
Set the switch lever in the OFF position.
Operate the shift lever to shift the chain.
Shift the chain to any gear that is five to seven steps from the largest sprocket. For bicycles with front double chainrings, shift to the largest chainring. If the chain rubs against the larger adjacent sprocket and makes noise, turn the cable adjustment barrel clockwise until the noise stops.
Turn the cable adjustment barrel counterclockwise.
While turning the crank, turn the cable adjustment barrel counterclockwise until you start to hear the chain rub on the larger sprocket.
Fine-tune the adjustment.
Turn the cable adjustment barrel five clicks in the clockwise direction from the point where rubbing started.
Check gear shifting.
Operate the shift lever to change gears while turning the crank. Ensure no noise occurs in any gear positions. If the rear derailleur does not shift properly, check if the derailleur hanger is straight using TL-RD11.
Set the switch lever to ON.
Check that gear shifting is smooth, consistent, and quiet in all gear positions while riding.
Maintenance
Replacing the Pulleys
Replace the guide pulley/tension pulley.
Check the arrow direction on the pulleys when installing them. Some models may not have a specified direction. Tighten guide pulley to 2.5-5 N·m and tension pulley to 2.5-5 N·m.
Replacing the B-axle
Remove the B-axle.
Push the B-axle from the inner side and use a slotted screwdriver to widen and remove the snap ring. Then, push the threaded portion of the B-axle against the stopper plate and use a hexagon wrench to unthread it.
Install a new B-axle.
Install the new B-axle in the reverse order of removal.
Replacing the Bumper
Note: There is no bumper on RD-M9120 / RD-M8120 / RD-M7120 / RD-M6100 / RD-M5100 / RD-M5130.
Remove the bumper.
Remove the bumper by flipping it forward.
Install a new bumper.
Slide the new bumper on from the side.
Applying Grease to the Chain Stabilizer
If friction changes or noise occurs, apply grease to the chain stabilizer.
Set the switch lever in the OFF position.
Remove the plate unit cover.
Use a 2 mm hexagon wrench to remove the plate unit cover screws.
Remove the cam unit and chain stabilizer.
Apply dedicated grease to the outer diameter of the roller clutch.
Use SHADOW RD+ Grease (Y04121000). Do not get grease inside the roller clutch, as it will cause malfunction.
Reassemble in reverse order.
Adjusting Friction
The friction level can be adjusted as desired or when it changes during use.
Set the switch lever in the ON position.
Remove the plate unit rubber cap or plate unit cover.
The rubber cap can be removed by hand. For models like RD-M7100/RD-M7120, remove the plate unit cover by unscrewing with a 2 mm hexagon wrench (1-1.5 N·m).
Turn the friction adjustment screw.
Use a hexagon wrench to turn the friction adjustment screw. Do not exceed 0.25 N·m to avoid damage.
Check the friction torque.
For RD-M9100/RD-M8100/RD-M8130/RD-M7100/RD-M6100/RD-M5100/RD-M5130, insert a hexalobular wrench into the outer plate and check the friction torque (4.4-5.4 N·m). For RD-M9120/RD-M8120/RD-M7120, remove the inner plate, guide pulley, and tension pulley, then insert a hexalobular wrench into the outer plate and check the friction torque (3.5-5.4 N·m).
Install the plate unit rubber cap or plate unit cover.
For models with a rubber cap, simply install it. For models with a cover, install the plate unit cover screws and tighten to 1-1.5 N·m.
Replacing the Plate, Plate Tension Spring, and Switch Lever
Set the switch lever in the OFF position.
If operating the switch lever while the plate unit cover is removed, hold the cam unit down with your finger to prevent it from sliding out.
Remove the plate stopper pin.
Use a cross head screwdriver to remove the plate stopper pin.
Turn the plate to loosen the plate tension spring.
Squeeze the outer casing holder and cable attachment portion together to move the link and turn the plate.
Remove the plate unit cover screws.
Use a 2 mm hexagon wrench to remove the screws.
Remove the plate unit cover.
Remove the chain stabilizer and cam unit.
Remove the plate axle.
Use a 4 mm hexagon wrench.
Remove the retaining clip and the switch lever.
Disassemble the unit as shown in the figure in the full manual.
Installation: Perform installation in the reverse order of removal.
- Apply Premium Grease (Y04110000) to the plate axle. Do not apply grease outside the indicated area.
- Insert the plate axle and fit the tip of the plate tension spring into the hole of the plate. Tighten to 7.8-9.8 N·m.
- Install the switch lever and engage the retaining clip. Set the switch lever in the OFF position.
- Set the chain stabilizer into the cam unit, ensuring the cam lobe is in the correct position. Do not install the plate unit cover if the plate unit is not fully seated against the cam unit.
- Apply dedicated grease to the plate unit cover gasket and install it along the groove.
- Install the plate stopper pin (tighten to 1 N·m).
- Install the plate unit cover screws (tighten to 1-1.5 N·m).
- Check friction and adjust as necessary.
Troubleshooting
- Gear shifting not smooth: Check derailleur hanger alignment (use TL-RD11), cable lubrication, and outer casing length.
- Chain rubbing or noise: Adjust the cable adjustment barrel. If noise persists, check for proper chain length and B-screw adjustment.
- Interference with chainstay: Adjust the B-screw to ensure the rear derailleur does not interfere with the chainstay.
- Abnormal pulley noise: Replace the pulleys if there is excessive play.
- Friction issues: If the roller clutch sticks or slides, check for grease contamination inside the clutch.
User Tips
- Cassette Compatibility: This derailleur is generally compatible with 9-speed cassettes. Some users have successfully used it with 11-40T and 11-42T cassettes without an extender, but proper adjustment is crucial. For 11-50T 9-speed cassettes, an extender might be necessary, especially for the M4000 model.
- Shifter Matching: Ensure your shifter matches the speed of the derailleur (e.g., a 9-speed derailleur requires a 9-speed shifter).
- Originality Check: When purchasing, verify the product's authenticity. Some users recommend filming the unboxing process.
- Smooth Operation: A good adjustment is key for quiet and efficient shifting. Take your time during the setup process.
Warranty and Support
For any issues not covered in this manual, or for professional assistance, please contact your place of purchase or a SHIMANO distributor.
You can find additional manuals and technical documents online at the official SHIMANO website: https://si.shimano.com.
A full user manual in PDF format is also available: User manual (PDF).