Dahao SD201, SD301

Contents

Dahao Servo Driver Board User Manual

Models: P/N SD201 Series, P/N SD301 Series

1. Introduction

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of the Dahao Servo Driver Board, designed for use with Chinese embroidery machines utilizing the Dahao control system. This board functions as a motor control card, crucial for the precise operation of your embroidery machine.

The Dahao Servo Driver Board is available in various part numbers, including SD201F, SD201, SD201G, SD301B, SD301D, and SD301. Please ensure you have the correct model for your specific machine.

Overview of the Dahao Servo Driver Board, showing various electronic components and circuitry.
Figure 1: Overview of the Dahao Servo Driver Board, displaying its main electronic components and layout.

2. Setup and Installation

Proper installation is critical for the functionality and longevity of the servo driver board. Always ensure the embroidery machine is powered off and disconnected from the main power supply before beginning any installation or maintenance procedures.

2.1 Compatibility Check

Manufacturers sometimes use similar components across different machine series. It is crucial to carefully verify that this specific Dahao Servo Driver Board model is compatible with your embroidery machine's Dahao control system. Refer to your machine's original documentation or consult with a qualified technician if unsure.

2.2 Installation Steps (General Guidelines)

  1. Power Disconnection: Ensure the embroidery machine is completely powered off and unplugged from the electrical outlet.
  2. Access Panel: Locate and open the access panel on your embroidery machine that houses the existing servo driver board.
  3. Remove Old Board (if applicable): Carefully disconnect all wiring harnesses and mounting screws from the old board. Note the orientation and connection points for each cable.
  4. Install New Board: Position the new Dahao Servo Driver Board in the designated slot. Secure it with appropriate mounting screws.
  5. Connect Wiring: Reconnect all wiring harnesses to their corresponding ports on the new board. Double-check each connection for proper seating and polarity. Refer to the wiring diagrams provided with your embroidery machine for precise connections.
  6. Close Panel: Once all connections are secure, close the access panel.
  7. Power On: Reconnect the machine to the power supply and power it on. Observe for any error messages or unusual behavior.
Close-up view of the SD301 new model Dahao Servo Driver Board, highlighting specific components and labels.
Figure 2: Close-up of the SD301 new model board, showing detailed circuitry and component labels.
Close-up view of the SD201 used model Dahao Servo Driver Board, highlighting specific components and labels.
Figure 3: Close-up of the SD201 used model board, showing detailed circuitry and component labels.

3. Operating Instructions

The Dahao Servo Driver Board is a component within the larger Dahao control system of your embroidery machine. Its primary function is to receive commands from the machine's main controller and translate them into precise movements of the servo motors, which drive various machine functions like needle movement, frame movement, and color changes.

Operation of the servo driver board is integrated into the overall operation of your embroidery machine. There are no direct user controls on the board itself. All operational commands are issued through the embroidery machine's control panel and software. Refer to your embroidery machine's specific user manual for detailed operating instructions.

4. Maintenance

To ensure optimal performance and extend the lifespan of your Dahao Servo Driver Board, follow these general maintenance guidelines:

  • Keep Clean: Periodically inspect the board for dust, lint, or debris accumulation. Use compressed air or a soft, dry brush to gently clean the surface. Avoid using liquids or harsh chemicals.
  • Environment: Ensure the operating environment is free from excessive moisture, extreme temperatures, and corrosive substances.
  • Static Electricity: When handling the board, always take precautions against static electricity, such as using an anti-static wrist strap.
  • Connections: Regularly check all cable connections to the board to ensure they are secure and free from corrosion.

5. Troubleshooting

If you experience issues with your embroidery machine that you suspect are related to the servo driver board, consider the following general troubleshooting steps:

  • Check Power: Verify that the machine is receiving power and that the board itself is powered on (if indicated by an LED).
  • Inspect Connections: Ensure all cables connected to the servo driver board are firmly seated and not damaged.
  • Error Codes: Consult your embroidery machine's manual for any error codes displayed on the control panel. These codes can often pinpoint the source of the problem.
  • Motor Function: If a specific motor is not functioning, check its connection to the driver board and the motor itself.
  • Machine Manual: Always refer to your embroidery machine's comprehensive troubleshooting guide, as it will contain specific diagnostics for your model.
  • Professional Assistance: If the issue persists after basic troubleshooting, it is recommended to contact a qualified technician or the supplier for further assistance.

6. Specifications

FeatureDetail
Part NameServo Motor Driver Board
ModelsP/N SD301 (new), P/N SD201 (used)
MaterialPlastic and Metal
UseEmbroidery Machines
TypeElectronic Parts
Compatible Machine SystemChinese embroidery machine Dahao system
OriginMainland China
Approximate Package Dimensions (L x W x H)30 cm x 20 cm x 15 cm
Approximate Package Weight2.8 kg

7. User Tips

  • Always confirm compatibility with your specific embroidery machine model before purchasing or installing. If you have any questions regarding compatibility, contact the supplier.
  • If you are looking for a specific embroidery machine part that is not listed, reach out to the supplier as they may have additional inventory not publicly displayed.
  • For urgent needs, consider expedited shipping options.

8. Warranty and Support

Yiwu Prague Embroidery Machine Parts Co., LTD. provides technical support for their products. For any inquiries regarding product functionality, installation, or troubleshooting beyond the scope of this manual, please contact the supplier directly.

Information regarding specific warranty periods and terms should be obtained from the seller at the time of purchase. It is recommended to retain your purchase records for any warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.