GlintDeer USB 5V Low Voltage Small Water Pump

Contents

USB 5V Low Voltage Small Water Pump User Manual

Model: USB 5V Low Voltage Small Water Pump

Brand: GlintDeer

1. Safety & Warnings

  • General Safety: Read all instructions before use to ensure safety and prevent damage.
  • Compatibility: Do not use with incompatible devices or accessories to avoid affecting product performance or damaging related equipment.
  • Abnormal Conditions: If the product shows any abnormal conditions such as smoke, unusual noises, or odors, immediately stop using it and disconnect power.
  • Non-Food Use: This product is not food-related. Keep it away from children and avoid accidental ingestion or touching of sharp parts (if any). Do not use for pumping potable liquids or food-grade substances.
  • Water Immersion: The pump is designed for full immersion in water. However, for prolonged use, it is recommended to seal the cable entry point with waterproof glue to prevent water intrusion into the cable housing.

2. Product Overview

The GlintDeer USB 5V Low Voltage Small Water Pump is a compact and efficient submersible pump designed for various low-pressure water circulation applications. It is ideal for small fish tanks, bonsai fountains, DIY aquarium setups, and hydroponic systems.

Various USB mini water pumps

Figure 1: Assortment of USB mini water pumps

Diagram showing pump pressure and applications

Figure 2: Pump pressure and typical applications

3. Specifications

FeatureSpecification
Brand NameGlintDeer
Model NumberWater Pump
TheoryElectromagnetic Pump
StructureSubmersible Pump
Power SourceUSB 5V
Voltage & Current5V 1.0A
Head (Max Lift)Approximately 3 meters
Water Flow Rate3 Liters/Minute
PressureLow Pressure
UsageWater
MaterialEngineering Plastic (Reinforced ABS)
Driving ModeBrushless DC Design, Magnetic Driving
Noise LevelLess than 35dB
Continuous Working LifeApproximately 500 hours
Dimensions (Approx.)Length: 10cm, Width: 10cm, Height: 10cm
Weight (Approx.)0.055 kg
CertificationNONE
OriginChina Mainland

4. Setup & Operation

4.1 Unboxing and Initial Preparation

  1. Carefully remove the pump from its packaging.
  2. Remove any protective films or coverings from the device.
  3. Inspect the pump for any visible damage. If damage is found, do not proceed with setup and contact support.

4.2 Connecting Hoses (Not Included)

The pump typically does not include hoses. You will need to purchase suitable tubing separately. The recommended fitting size for the pump's outlet is approximately 7mm inner diameter.

Close-up of the pump outlet

Figure 3: Pump Outlet

Close-up of the pump inlet

Figure 4: Pump Inlet

4.3 Power Connection

The pump is powered via a standard USB 5V connection. Connect the USB cable to a compatible 5V USB power source (e.g., USB wall adapter, power bank, computer USB port).

Close-up of the USB interface

Figure 5: USB Interface

4.4 Operating the Pump

  1. Ensure the pump is fully submerged in the water before connecting power. The pump is not self-priming and requires immersion to function correctly.
  2. Connect the USB cable to a 5V power source. The pump will start operating immediately.
  3. To stop the pump, simply disconnect the USB power source.

Video 1: Unboxing and demonstration of pump operation in water.

Application example with water flowing from the pump

Figure 6: Example of pump in operation, creating water flow.

5. Maintenance

  • Cleaning: The pump is designed for easy external cleaning. Disconnect power before cleaning. Rinse the pump with clean water to remove any debris or buildup.
  • Impeller Access: The pump is a sealed unit, and the impeller is not designed for user disassembly or cleaning. Attempting to disassemble the pump may damage it and void any potential support.
  • Cable Integrity: Regularly check the USB cable for any signs of wear or damage. Replace if necessary.

6. Troubleshooting

  • Pump Not Starting:
    • Ensure the USB power source is active and providing 5V.
    • Check that the USB cable is securely connected to both the pump and the power source.
    • Verify the pump is fully submerged in water.
  • Weak Water Flow:
    • Check for blockages in the pump inlet or outlet, or in any connected tubing.
    • Ensure the water level is sufficient for the pump to operate effectively.
    • Confirm the power source is providing adequate current (1.0A recommended).
  • Excessive Noise:
    • While the pump is designed to be quiet (under 35dB), some operational noise is normal.
    • Ensure the pump is stable and not vibrating against hard surfaces.
    • Check for any foreign objects that might be causing obstruction or rattling inside the pump.
  • Short Lifespan / Pump Failure:
    • The pump has a rated continuous working life of approximately 500 hours. Continuous operation beyond this may lead to premature wear. Consider intermittent use for extended longevity.
    • Ensure the pump is always submerged in water during operation to prevent dry running, which can cause overheating and damage.

7. User Tips

  • For applications requiring long-term water immersion, consider applying a waterproof sealant (e.g., silicone glue) around the cable entry point to enhance water resistance and prevent potential leaks into the cable housing.
  • The pump operates simply by connecting to a 5V USB power source and stops when disconnected. No additional switches are typically present on the pump itself.
  • If using for a fountain or aquarium, ensure the water is clean to prevent debris from clogging the pump or reducing its efficiency.
  • While the pump is submersible, avoid operating it dry as this can lead to damage.

8. Warranty & Support

For any product inquiries, technical support, or warranty claims, please contact the seller or manufacturer directly.

Manufacturer Contact Information:

  • Country: China
  • Telephone: +86-13417026232
  • Email: xinhui0518@163.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.