1. Introduction
Thank you for choosing the PEAKMETER PM8248S Smart Digital Multimeter. This device is a professional, auto-ranging digital multimeter designed for measuring AC/DC voltage, AC/DC current, resistance, capacitance, frequency, and temperature. It also features Non-Contact Voltage (NCV) detection, Live Test, Transistor (hFE) test, continuity, data hold, work light, backlight, and an auto power-off function. Its compact design and robust construction make it ideal for both professional and DIY electrical tasks.
2. Safety Information
WARNING: To avoid possible electric shock or personal injury, and to avoid possible damage to the meter or to the equipment under test, follow these safety rules:
- Always ensure the meter is in the correct function and range for the measurement.
- Do not apply more than the rated voltage, as marked on the meter, between the terminals or between any terminal and earth ground.
- Use caution when working with voltages above 30V AC RMS, 42V peak, or 60V DC. Such voltages pose a shock hazard.
- Before making current measurements, ensure the meter's fuses are intact and the test leads are connected to the correct input jacks.
- Before rotating the function switch to change functions, disconnect the test leads from the circuit under test.
- Do not use the meter if it is damaged or if the test leads are damaged. Inspect the meter and test leads before use.
- Do not operate the meter around explosive gas, vapor, or dust.
- When servicing the meter, use only specified replacement parts.
- Always remove the test leads before opening the battery cover.
3. Package Contents
Upon opening the carrying case, you should find the following items:
- PEAKMETER PM8248S Smart Digital Multimeter
- Test Leads (Red and Black)
- K-Type Thermocouple
- User Manual
- Carrying Case
- Spare Fuses (typically 2)

4. Setup
4.1. Battery Installation
- Ensure the multimeter is turned off and disconnect any test leads.
- Locate the battery compartment cover on the back of the meter.
- Open the battery compartment cover (refer to the unboxing video for visual guidance).
- Insert three 1.5V AAA batteries, observing the correct polarity (+ and -).
- Close the battery compartment cover securely.

4.2. Connecting Test Leads
- For most measurements (voltage, resistance, continuity, capacitance, frequency, temperature), insert the red test lead into the "VΩHz" jack and the black test lead into the "COM" jack.
- For current measurements (mA), insert the red test lead into the "μA/mA" jack and the black test lead into the "COM" jack.
- Ensure connections are firm before taking measurements.
5. Operating Modes and Functions
The PM8248S features an Auto Range function, simplifying operation by automatically selecting the appropriate measurement range. Use the 'SEL/NCV' button to cycle through different functions within a mode (e.g., AC/DC voltage, resistance/continuity).
5.1. Power On/Off and Display
- Press the orange power button to turn the meter ON or OFF.
- The meter features a 6000-count digital display with a bargraph.
- The backlight can be activated for better visibility in low-light conditions.
- The meter will automatically power off after a period of inactivity to conserve battery life.
5.2. Measuring DC/AC Voltage
- Connect the test leads as described in Section 4.2 (red to "VΩHz", black to "COM").
- Turn on the meter. It will typically default to Auto Range Voltage mode.
- Touch the test probes to the circuit points where you want to measure voltage.
- The display will show the voltage reading. Use the 'SEL' button to switch between AC and DC voltage if needed.

5.3. Measuring DC/AC Current (mA)
- Turn off the circuit power.
- Connect the red test lead to the "μA/mA" jack and the black test lead to the "COM" jack.
- Break the circuit and connect the meter in series with the load.
- Turn on the circuit power. The display will show the current reading.
- Use the 'SEL' button to switch between AC and DC current if needed.
- Turn off the circuit power before disconnecting the meter.
5.4. Measuring Resistance and Continuity
- Connect the test leads (red to "VΩHz", black to "COM").
- Turn on the meter and select the Resistance/Continuity mode using the function switch or 'SEL' button.
- Touch the test probes across the component to measure resistance.
- For continuity, if the resistance is below a certain threshold (typically <30Ω), the buzzer will sound.
5.5. Measuring Capacitance
- Connect the test leads (red to "VΩHz", black to "COM").
- Turn on the meter and select the Capacitance mode.
- Ensure the capacitor is discharged before testing.
- Touch the test probes to the capacitor terminals. The display will show the capacitance value.
5.6. Measuring Frequency
- Connect the test leads (red to "VΩHz", black to "COM").
- Turn on the meter and select the Frequency mode.
- Touch the test probes to the signal source. The display will show the frequency in Hz.

5.7. Measuring Temperature
- Ensure the meter is off.
- Insert the K-Type thermocouple into the dedicated K-TYPE input jacks, observing polarity.
- Turn on the meter and select the Temperature mode.
- Place the thermocouple tip on or near the object whose temperature you wish to measure.
- The display will show the temperature in °C or °F.

5.8. Non-Contact Voltage (NCV) Detection
- Press the 'NCV' button to activate NCV mode.
- Move the top end of the meter close to a live AC voltage source.
- The meter will indicate the presence of AC voltage through an audible beep and visual LED indicators.

5.9. Live Test
This function helps identify live wires. Refer to the manual for specific instructions on using the Live Test feature safely.
5.10. Transistor (hFE) Test
The meter includes a dedicated socket for testing NPN and PNP transistors. Insert the transistor leads into the corresponding E, B, C holes to measure hFE.
5.11. Data Hold
Press the 'HOLD' button to freeze the current reading on the display. Press it again to release.
5.12. Work Light
The meter is equipped with a work light to illuminate the measurement area. Activate it as needed.
6. Specifications
Measurement Ranges and Accuracy
| SPECIFICATIONS | RANGE | ACCURACY |
|---|---|---|
| DC Voltage | 6V/60V/600V | ±(0.8%+3) |
| AC Voltage | 6V/60V/600V | ±(1.2%+3) |
| DC Current | 600mA | ±(1.0%+3) |
| AC Current | 600mA | ±(1.5%+3) |
| Resistance(Ω) | 6kΩ/60kΩ/600kΩ/6MΩ/10MΩ | ±(1.0%+3) |
| Capacitance(C) | 60nF/600nF/6μF/60μF/600μF/6mF | ±(4.0%+5) |
| Frequency | 30 ~ 1000Hz | ±(0.5%+2) |
| Temperature(°C/°F) | -20°C ~ 1300°C / -4°F ~ 2372°F | ±(1.0%+3) |
Features
| Feature | |
|---|---|
| Display | 6000counts |
| Auto Range | √ |
| Bargraph Display | √ |
| True RMS | √ |
| Transistor | √ |
| Continuity | √ |
| NCV | √ |
| Live Test | √ |
| Data Hold | √ |
| Work light | √ |
| Back Light | √ |
| Auto Power Off | √ |
General Characteristics
| Power supply | 3x1.5V AAA batteries |
| Weight | Approx. 250g (without batteries) |
| Size | 169mm x 83mm x 53mm |
| Safety Rating | EN61010-1,-2-030,EN61010-2-033, EN61326-1,CAT.III 600V |
7. Maintenance
7.1. Cleaning
- Wipe the meter with a soft, damp cloth. Do not use abrasives or solvents.
- Keep the display clean and free from dust.
7.2. Battery Replacement
When the battery indicator appears on the display, replace the batteries promptly to ensure accurate readings. Follow the steps in Section 4.1 for battery installation.
7.3. Fuse Replacement
If the current measurement function stops working, the fuse may be blown. Refer to the full user manual for instructions on how to safely replace the internal fuses. Always use fuses of the specified type and rating.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Meter does not power on | Dead or incorrectly installed batteries | Replace batteries, check polarity |
| No reading or 'OL' displayed | Incorrect range, open circuit, or overloaded input | Check connections, ensure circuit is closed, select appropriate function/range |
| Inaccurate readings | Low battery, damaged test leads, or external interference | Replace batteries, inspect/replace test leads, move away from strong electromagnetic fields |
| Current measurement not working | Blown fuse | Replace the fuse with the correct type and rating |
9. User Tips
- Many users find this multimeter to be very easy to use, making it suitable for beginners and experienced technicians alike.
- Always double-check your test lead connections and the selected function before taking any measurement to prevent damage to the meter or the circuit.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact information provided by your retailer or the manufacturer's official website. Keep your purchase receipt as proof of purchase.