1. Product Overview
The Retekess TD021 is a wireless repeater signal amplifier designed to extend the range of compatible Retekess restaurant pager and nurse calling systems. It amplifies wireless signals, effectively removing signal blind spots and ensuring reliable communication between transmitters (call buttons) and receivers (pagers).

Note:
- This amplifier is specifically designed for Retekess restaurant pager call systems, such as the T117.
- It is NOT suitable for other pager systems like TD157 or TD163.
2. Package Contents
- 1 x RF Wireless Repeater (Retekess TD021)
- 1 x Power Adaptor (EU/US/AU/UK optional, depending on region)

3. Setup Instructions
3.1 Placement
The TD021 amplifier should be strategically placed between the wireless transmitters (e.g., call buttons) and the receivers (e.g., watch pagers) to effectively extend the signal range. Optimal placement depends on the specific environment and potential signal obstructions.


3.2 Power Connection
- Connect the provided power adapter to the DC 12V 1A input port on the TD021 amplifier.
- Plug the power adapter into a standard AC 100-240V 50/60Hz electrical outlet.
- The red "POWER" indicator light on the front of the unit should illuminate, indicating that the device is receiving power.
3.3 DIP Switch Configuration
The TD021 features DIP switches on its rear panel for configuration, especially when multiple amplifiers are used in a stacked setup (up to 6 units). This configuration helps prevent interference and ensures proper signal routing.

To configure the DIP switches:
- For a single amplifier or the first unit in a stack: Set DIP switch '1' to the ON position.
- For the second amplifier in a stack: Set DIP switch '2' to the ON position.
- For the third amplifier in a stack: Set DIP switches '1' and '2' to the ON position.
- For the fourth amplifier in a stack: Set DIP switches '1' and '3' to the ON position.
- For the fifth amplifier in a stack: Set DIP switches '2' and '3' to the ON position.
- For the sixth amplifier in a stack: Set DIP switches '1', '2', and '3' to the ON position.
Important:
- Ensure the DIP switches are set correctly according to your setup to avoid signal conflicts.
- Only switches 1, 2, and 3 are used for stacking configuration. Other switches should remain OFF unless specified for advanced configurations (not covered in this manual).
4. Operating Instructions
Once properly set up and powered on, the TD021 amplifier operates automatically. It continuously monitors for incoming wireless signals from compatible transmitters.
- When a compatible transmitter (e.g., a call button) sends a signal, the TD021 receives it.
- The green "SEND" indicator light on the front of the unit will briefly illuminate, indicating that a signal is being processed and re-transmitted.
- The amplifier then re-transmits the amplified signal to extend its reach to the intended receivers.
The primary function is to enhance the signal and remove signal blind spots, ensuring that call signals reach receivers reliably across a wider area.

5. Maintenance
To ensure the longevity and optimal performance of your Retekess TD021 amplifier, follow these simple maintenance guidelines:
- Cleaning: Use a soft, dry cloth to wipe the exterior of the unit. Avoid using abrasive cleaners, solvents, or strong chemicals, as these can damage the casing.
- Environment: Keep the amplifier in a dry environment, away from direct sunlight, excessive heat, humidity, and dust.
- Ventilation: Ensure that the ventilation slots (if any) are not blocked to prevent overheating.
- Power: Disconnect the power adapter from the wall outlet if the device will not be used for an extended period.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power indicator (Red "POWER" LED is off) |
|
|
| Signals not being amplified or received by pagers |
|
|
| Green "SEND" LED does not light up when a call button is pressed |
|
|
7. Specifications
| Feature | Detail |
|---|---|
| Brand | Retekess |
| Model Number | TD021 |
| Product Type | Wireless Repeater Signal Amplifier (Nurse Calling System) |
| Working Frequency | 433MHz |
| Sensitivity | -108dBm |
| Standby Current | 30mA |
| Working Current | <255mA |
| Adapter Input | AC 100-240V 50/60Hz |
| Working Voltage | DC 12V 1A |
| Transmitting Power | 500mW |
| Transmitting Distance | Double the distance of the launch button (approx. 500m in open area) |
| Dimensions (L x W x H) | 100 x 70 x 25mm |
| Weight | 102g |
| Battery Included | No |
| Certification | CE, FCC |
| Origin | Mainland China |
8. User Tips
- DIP Switch Clarity: Many users find the DIP switch configuration challenging. Always refer to Section 3.3 and the provided diagram to ensure correct settings, especially when using multiple amplifiers.
- Optimal Placement: Experiment with different locations for the amplifier to find the best spot that minimizes signal blind spots and maximizes coverage in your specific environment. Consider mounting it higher if possible.
- Compatibility Check: Double-check that your existing pager system is compatible with the TD021. It is designed for specific Retekess systems like the T117 and will not work with all models or other brands.
- Purpose-Built: Remember this device is an RF wireless repeater for pager systems, not a cellular signal booster. It will not amplify mobile phone networks.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.