ElecDemo PE43702

Contents

ElecDemo PE43702 Digital RF Attenuator Module User Manual

Model: PE43702 | Brand: ElecDemo

1. Introduction

The ElecDemo PE43702 is a high-performance digital RF attenuator module designed for various applications, particularly in education and learning. This module integrates a PE43702 main chip and an LP5900 power chip, ensuring stable and reliable operation. It features a wide bandwidth, precise attenuation steps, and multiple control modes.

Highlights:

  • Utilizes numerous filter capacitors for power supply decoupling, designed for high-frequency circuits with excellent frequency characteristics.
  • Incorporates T company's special RF chip LP5900 for power supply, significantly reducing fluctuation and ripple interference compared to direct user input.

2. Specifications

FeatureDescription
Model NamePE43702 7 Bit RF Attenuator Module
Attenuator Type50Ω Digital RF Attenuator
Bandwidth9KHz ~ 4GHz
Attenuation Range0 to 31.75 dB
Attenuation Step0.25 dB
Maximum Gain31.75 dB
IIP3+57 dBm
Power Supply Range3V ~ 5V (Typical 5V)
Control ModesDirect Parallel, Latched Parallel, Serial
High Attenuation ModePUP configuration
Module Size50mm x 50mm
PE43702 module with dimensions 50mm by 50mm
Figure 2.1: Module Dimensions (50mm x 50mm)

3. Component Overview

The PE43702 module features several key components for its operation:

Labeled diagram of the PE43702 Digital RF Attenuator module showing power supply, DIP switches, signal input/output, and main chips.
Figure 3.1: PE43702 Module Labeled Components
  • Power Supply (GND, 5V): Input for the module's operating voltage. Designed with a foolproof function to prevent incorrect connections.
  • 7-digit Dialing Code (DIP Switch): Used for setting attenuation levels in direct parallel mode.
  • SP2 CNC: Likely a control or status indicator/port.
  • Signal Input (RF-IN): SMA connector for the RF signal to be attenuated.
  • Signal Output (RF-OUT): SMA connector for the attenuated RF signal.
  • LP5900 Power Chip: Dedicated power management chip for stable operation.
  • PE43702 Main Chip: The core digital RF attenuator IC.
  • DATA, CLK, LE Pins: Control pins for serial and latched parallel modes.

4. Setup Instructions

  1. Power Connection: Connect a stable 5V DC power supply to the 'GND' and '5V' pins on the module. Ensure correct polarity. The power input connector is designed with a foolproof function.
  2. RF Signal Input: Connect your RF signal source to the 'RF-IN' SMA connector.
  3. RF Signal Output: Connect your measurement device or next stage circuit to the 'RF-OUT' SMA connector.
  4. Control Mode Selection: Determine your desired control method (DIP switch for direct parallel, or external control via DATA, CLK, LE pins for latched parallel or serial mode).

5. Operating Instructions

5.1. Attenuation Setting via DIP Switch (Direct Parallel Mode)

The module features a 7-digit DIP switch for setting the attenuation. Each switch corresponds to a specific attenuation value, allowing for precise control in 0.25dB steps up to a maximum of 31.75dB.

  • The DIP switches are labeled P/S, 0.25, C0.5, C1, C2, C4, C8, C16. These labels likely correspond to attenuation values in dB.
  • To set a desired attenuation, switch the corresponding DIP switches to the 'ON' position. The total attenuation will be the sum of the values of the 'ON' switches.
  • For example, to achieve 1.25dB attenuation, you would turn ON the switches corresponding to 0.25dB, C0.5dB, and C0.5dB (if C0.5 is a single switch, then 0.25 + 1.00, or 0.25 + 0.5 + 0.5 if there are two 0.5 switches). Please refer to the specific attenuation values marked on your module's DIP switches for exact settings.

5.2. Advanced Control Modes (Latched Parallel, Serial)

The module supports Latched Parallel and Serial control modes via the DATA, CLK, and LE pins. Detailed programming instructions and timing diagrams for these modes are typically provided in the PE43702 datasheet or accompanying source code. Users interested in these modes should consult the relevant documentation.

6. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the module. Avoid using liquids or abrasive cleaners.
  • Storage: Store the module in a dry, dust-free environment when not in use.
  • Handling: Handle with care to avoid physical damage to the connectors or components.
  • Environmental Conditions: Operate the module within its specified temperature and humidity ranges to ensure optimal performance and longevity.

7. Troubleshooting

  • No RF Output or Incorrect Attenuation:
    • Verify that the 5V power supply is correctly connected and stable.
    • Check all RF-IN and RF-OUT cable connections for proper seating and integrity.
    • If using DIP switches, ensure they are set correctly for the desired attenuation.
    • If using serial/latched parallel control, verify your control signals (DATA, CLK, LE) and programming logic.
  • Module Not Responding:
    • Ensure the power supply is within the 3V-5V range.
    • Check for any visible damage to the module.
  • Need Technical Documentation (Schematic/Source Code):
    • A PDF schematic and STM32F103RCT6 Source Program are available. Please contact customer service after purchase to receive these documents.

8. User Tips

  • For precise attenuation, always double-check the DIP switch settings or your control code.
  • When experimenting with different attenuation levels, it's advisable to start with higher attenuation to protect sensitive downstream equipment.
  • Consider using shielded cables for RF connections to minimize external interference.

9. Warranty and Support

9.1. Warranty Information

ElecDemo provides a limited warranty on defective items for a specified period. This warranty typically covers manufacturing defects but excludes items damaged due to misuse or improper handling. Accessories are generally covered by a 3-month warranty.

Please note that the displayed images are for reference only; actual product appearance may vary slightly due to different production batches.

9.2. Customer Support

For any product-related inquiries, technical assistance, or to request the PDF schematic and STM32F103RCT6 Source Program, please contact ElecDemo customer service. We are committed to helping our customers and will strive to resolve any issues to your satisfaction.

10. Frequently Asked Questions

Q: What is the maximum attenuation I can achieve?
A: The module provides a maximum attenuation of 31.75 dB.
Q: What is the attenuation step size?
A: The attenuation can be adjusted in precise 0.25 dB steps.
Q: What power supply voltage is required?
A: The module operates with a power supply range of 3V to 5V, with a typical operating voltage of 5V.
Q: Can I get the schematic and source code?
A: Yes, a PDF schematic and STM32F103RCT6 Source Program are available upon request from customer service after purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.